1968 Ford Mustang

Used passenger side (right hand) spring from a door latch assembly fits many Ford and Mercury cars. This will fit all years 1967-70. 

C-4 transmission 90 degree brass fitting for the rear oil cooler line. New reproduction with jamb nut and "O"-ring. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.

Application; 390, 427, 351CJ, 428CJ, and 429CJ all with C6 transmission. 428CJ and 429CJ 4 speed transmissions. 1970 351C-4v with FMX.U-joint size 1330, overall length 8-3/4 inches.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used Trunnion for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Trunnion is the white plastic bone looking thing with a hole in it. Attaches the Link and Rod from Servo Bell Crank. Ford part number C7ZZ-9D766-A.

Reproduction machined tube seat set, for ram cylinder and control valve on early 1967 Mercury Cougar and Ford Mustang with the 1/4" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that starting in mid to late 1967, the control valves had 5/16" fittings all the way to 1970.

Cancelling cam for the 67-69 Cougars and Mustangs with fixed columns. This cam is what returns your turn signal switch to the off position. This is not the same cam which comes inside tilt columns.

This is a stock photo, the actual lever we have will most likely be worn and will not be as nice as the one pictured. Grade A speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we may price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G This icon means that we're looking to buy...

Grade B speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln. We won't always have this item in stock, and we price them based on conditiion of the plastic chrome.The 1968 Electrical manual shows this part to be from Lincoln. C7VA-9D752-G

One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

1968 Mercury Cougar / Ford Mustang complete ashtray assembly with lighter.The manufacturer claims that it will fit a 1967, but this one is about 1/4 inch shorter over all compared to the 1967 unit. *NOTE* Will only fit the 1968 dashes.Click on images to enlarge. ...

Special zerk fittings with extra long extensions. Allows easy access to hard to reach zerk fittings. Helps solve squeaky upper control arms.

Reproduction vacuum hose with green and white stripes. Every effort has been made to make this hose set as close to the originals as possible. The correct thickness and rubber type means it won't kink or lose vacuum when exposed to the hot temperatures under the hood.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

This unit mounts on the main air chamber, it opens and closes the air vent. NOS or new old stock.  This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Tested and working, Ford box.Replaces Ford part # C6OZ-18C311-A. ...

C8OE-C-SR WCCC Carter service replacement anti backfire valve, but without the outer cover having the concours correct stampings.These units are used, not tested and one should assume they are non-functional.

This valve is used on Mercury Cougars and Ford Mustangs equipped with factory A/C to stop the flow of warm coolant when A/C is on.This valve is functionally the same as the OEM, but has obvious cosmetic differences from the factory valve.Replaces Ford Part #: C7ZZ-18495-A.

Vacuum tested working hot water valve for Mercury Cougars and Ford Mustangs equipped with factory A/C. This valve stops the flow of warm coolant when the A/C is on and has the original cast brass valve with bracket and vacuum pod. We are unable to guarantee that the water seal is good. Ford part # C7ZZ-18495-A, casting number on vacuum valve C7ZA-18C310-A.

Core C-4 Transmission valve body for any 1967-68 Mercury Cougar or 1967-69 Ford Mustang with code "W" transmission code on the door tag. This is only for 1967 through 1969 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in...

Core C-4 Transmission valve body for any 1968 Mercury Cougar or 1968 Ford Mustang with code "W" transmission code on the door tag. This is only for 1968 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket,...

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

New old stock driver side vent window handle for any 1968 Mercury Cougar or Ford Mustang.  Drive pins and washers included.Ford part number C8OZ-5422917-B

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

Used grade "A" driver side (left hand) vent window frame as it comes out of the door and is just the bare window frame. This is not a perfect part but it will look good on a low mile car that shows a little patina. The weatherstrip track that continues down into the door can be had with this part for no extra charge, please mention it in the comments section when you order online. Ford part # C7ZZ-6522205-A. Casting # C7ZB-6522223-A Check out our video below for helpful tips on disassembling...

Used grade A stainless steel vent window glass frame for the left side or driver side door on a 68 Mercury Cougar or Ford Mustang. Similar frame as the 1967

New old stock instrument panel voltage regulator or IVR for all 1967-68 Mercury Cougar and Ford Mustang. Additionally fits 1967-68 Ford full size, 1966-68 Torino,CycloneMounts to the rear of the instrument clusters, voltage regulator for dash gauges power.  Ford part number C6DZ-10804-A. Check out the video below on our new gauge tester: ...

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

This is a plastic cushion, washer and/or spring between the lower knuckle and inner tube on a 1968 - 1973 tilt-away steering column. These have a larger diameter than the 1967 plastic cushion.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C6OE-A. Found on many Ford 289 engines from 1966-67. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other casting...

Dated 7G3, July 3, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-8505-H. Found on many Ford 390, 427, and 428CJ engines from 1968. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers....

Dated 7M9, December 9, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-8505-H. Found on many Ford 390, 427, and 428CJ engines from 1968. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Dated 8F4, June 4, 1968. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C8AE-8505-H. Found on many Ford 390, 427, and 428CJ engines from 1968. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers....

Original NOS part, new in box. Ford part # C5ZZ-6503110-A

Used on the optional 68 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1969 Eliminator, 68-69 Torino and Mustang. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. WCCC is the only retailer offering these at present. Sold individually. Replaces Ford part number C8ZZ-1210-A. ...

Used on the optional 1968 Mercury Cougar styled steel wheel in the 14x6" size as well as the 1968 Torino and Mustang. Also used on the 1969 Eliminator 12 hole wheel so as to match the brushed center cap. Master Parts Catalog description: 15-3/8" O.D., 12" I.D, 2" wide, brushed finish, sold individually. These are easy to identify from the 1967 or 1969 - 1970 as they are the only ring with a brushed finish used on the SS wheels 1967-1970. These are getting very hard to come by, and most...

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction concours weave black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown...

Reproduction dark red headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Restored pair of show-quality passenger and driver side quarter window frames for the 67 - 68 Mustang. Good for both Coupe and Convertible. The only weatherstripping we carry for these frames are the vertical seals, we currently do not carry the Mustang glass to frame seals. These look awesome when restored, better than new. Mirror finish. We take your tired original window frames and have them professionally rechromed. Send your cores in advance to avoid the core charge, or wait...

NOS window crank knob, color is Aqua Blue, 1968 and 1969 only color. Fits 1968-69 Mercury Cougar and 1968 Ford Mustang and other Fords. Ford part number C8SZ-6523352-A1K.

Easy to install quality reproduction. Includes crescent spring and correct aluminum pin that features shoulder and locking knurls. Does not look or feel much like the original. Not really a stock color, fits 1968-71 cars and about 1 month into 1972. Please see the window crank handles to see the difference between 1968-71 handles and 1972-73 window crank handles. Replaces Ford Part # C8AZ-6223352 *TIP* To install remove your window crank and place knob and crank in the jaws. To protect the...

Good used

Good used

This is a good used fitting with large and small nipples for use with the foot actuated washer pumps found on 1967-68 Mercury Cougar and Ford Mustang. Good used part that we verify the check valve is working. These screw into of the rubber covered pumps.

Used wiring cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Unique to the 1968 and 1969 tilt column, fixed column version will not fit on a tilt without modification. Ford part number C8ZZ-13376-A or C8ZZ-13376-B.

Factory used and tested under dash wiring harness for all 1968 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This harness plugs into the speaker plug of the radio, and connects the kick panel speakers in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door wiring harness that has the speaker plug for the door mounted speakers in 1969-70 cars. White speaker wire goes to the passenger side speaker, and the orange colored wire...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...