1968 Ford Mustang

1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D. Click on images to enlarge. Check out our video on rebuilding your shifter below: ...

Fragile black plastic channel selection button that often gets broken. Requires advanced skills to remove and replace.

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

NOS new old stock Motorcraft water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Used Autolite water temperature sending unit, fits Ford 289, 302, 390, 427, 428CJ. 260° stamped, for Mercury Cougar 1967-69, and Ford Mustang 1966-69.  Ford number C6DZ-10884-B. *Note - these are specifically NOT for 1969 351W. Ford had a unique part number for that one engine.... and we don't stock that one. Sorry. Check out the video below on our new gauge tester: Check out our video on replacing the fuel system on a '68 Cougar! ...

Reproduction A/C suction service valves for Mercury Cougars and Ford Mustangs equipped with factory A/C.

Used Servo Assembly for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Servo is the rubber bellows. Ford part number C7ZZ-9C735-A.

Used servo cover from a 1968-69 Ford C-6 transmission. This cover has the big D cast into it, which designates it as an "D" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, for 1968 Mercury Cougar and Ford Mustangs with X code 390-2V engines. Additionally, 1969 Mercury Cougar and Ford Mustang with the S code 390-4V or 390IP engine. Cover only, marked C6AP-7D027-A.

Used servo cover from a 1967-68 Ford C-6 transmission. This cover has the big H cast into it, which designates it as an "H" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, with Mercury Cougar and Ford Mustangs with S code 390-4V engines. Cover only, marked C6AP-7D027-D.

Used servo cover from a 1969-71 Ford C-6 transmission. This cover has the big R cast into it, which designates it as an "R" Intermediate Servo Band Cover. Typically, this cover would be found on U code C6's, from 1968-70 Mercury Cougar and Ford Mustangs with Q or R code 428CJ engines. Additionally 1971 Mercury Cougar or Ford Mustang with J or C code 429CJ engines. 1968-71 Ford and Mercury mid sized cars also with 428CJ or 429CJ. Cover only, marked C8OP-7D027-A.

Used Shaft for the bell crank on the 1967-68 Mercury Cougar and Ford Mustang with speed control. The Shaft attaches to the Servo Bracket. It Bell Crank pivots on the Shaft. Ford part number C7ZZ-9D768-A.

C8ZZ-7400-D4Assembly 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang. Small block 289 and 302 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. May be either large or small trunion. Subject to availability. Check out our video on rebuilding your shifter below: ...

You will not need to make any modifications to run this leather unit in place of your original rubber boot used on three and four speed manual transmissions.

Clean no nonsense look. 12MM Threads. Check out our video on rebuilding your shifter below:

For those who want to want a correct looking interior in conjunction with their modern transmission. Check out our video on rebuilding your shifter below: ...

Set of reproduction Ford Top Loader 4 speed shift rods for 1967-68 Mercury Cougar or Ford Mustang with 289 or 302 engines only. 

C7ZZ-7400-C4Assembly 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Big block 390 engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. Check out our video on rebuilding your shifter below: ...

C8ZZ-7400-C4Assembly 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang after 1-2-1968. Big block 390 and 428CJ engines only. Includes shifter mechanism, shift rods, and shift lever. All in used condition. Check out our video on rebuilding your shifter below: ...

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

C8ZZ-7210-A 4 Speed shift lever with round reverse lockout provision. For any 1968 Mercury Cougar and Ford Mustang until 1-2-1968. The early lever can be identified by measuring the distance between bolt holes. 1-13/16" spacing between the holes is the C8ZZ-7210-A lever. *Note - Must be used with Trunion C5ZZ-7210-D, sold separately.

C8ZZ-7210-C Shift lever for all Mercury Cougar and Ford Mustangs after 1-2-1968. This 1968 lever can be identified by measuring the distance between bolt holes. 2" spacing between the holes is the C8ZZ-7210-C lever. *Note - Must be used with Trunion C8ZZ-7210-D, sold separately.

C8ZZ-7210-B 4 Speed shift lever with round reverse lockout provision. For any 1968 Mercury Cougar and Ford Mustang after 1-2-1968. The early lever can be identified by measuring the distance between bolt holes. 2" spacing between the holes is the C8ZZ-7210-B lever. *Note - Must be used with Trunion C8ZZ-7210-D, sold separately.

1967 - 1968 Manual 3 Speed Shifter Mechanism - Used C5ZZ-7400-C 3 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Check out our video on rebuilding your shifter below: ...

C8ZZ-7400-B 3 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang after 1-2-1968. Check out our video on rebuilding your shifter below: ...

C8ZZ-7400-A 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang after 1-2-1968. Check out our video on rebuilding your shifter below: ...

C7ZZ-7400-C 4 Speed manual transmission shift control assembly for any 1967 Mercury Cougar and Ford Mustang and 1968's up until 1-2-1968. Big block 390 engines only. Check out our video on rebuilding your shifter below: ...

C8ZZ-7400-C 4 Speed manual transmission shift control assembly for any 1968 Mercury Cougar and Ford Mustang after 1-2-1968. Big block 390 and 428CJ engines only. Check out our video on rebuilding your shifter below: ...

Adapter plate for mounting the 3 or 4 speed shifter control assembly to the Top Loader transmission.Ford part # C7ZZ-7E046-A. Check out our video on rebuilding your shifter below: ...

C5ZZ-7210-D "U" shaped bracket that attaches the 3 speed shift lever to the shifter control assembly. For use on all 1967 Mercury Cougar and Ford Mustangs with the 3 or 4 speed shift lever, and 1968 shift levers through 1-2-1968. Bottom bracket only, called a Trunion (see illustration). Measurement of hole spacing is 1-13/16 inches on center. *Note - Must be used with 3 speed shift lever C5ZZ-7210-C, or 4 speed shift lever C5ZZ-7210-M. Check out our video on rebuilding your shifter below: ...

C8ZZ-7210-D "U" shaped bracket that attaches the 3 speed shift lever to the shifter control assembly. For use on all 1968 Mercury Cougar and Ford Mustangs after 1-2-1968, with the 3 & 4 speed shift levers. Bottom bracket only, called a Trunion (see illustration). Measurement of hole spacing is 2 inches on center. *Note - Must be used with 3 speed shift lever C8ZZ-7210-C, or 4 speed shift lever C8ZZ-7210-B. Check out our video on rebuilding your shifter below: ...

This tower is identical to every other 1967-70 tower in every way except the reinforcement plate.The reinforced shock towers came out in late March 1968 and were used on all big block Cougars and Mustangs. 390-2V / 390-4V / 427 / 428CJ. No specific part number exists for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...

This tower is identical to every other 1967-70 tower in every way except the reinforcement plate. In late 1968 390-427-428 Mercury Cougar and Ford Mustang came with this reinforced tower due to a problem they were having with structural cracking. No specific part number for this structural front suspension section with or without wrap around bracing. This example was actually taken from a very early 1969 San Jose built Cougar and is identical to the late 68 Big Block Tower. The only reason you...

Passenger side (right hand) front seat floor pan. This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market.   1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up....

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This surround or "U" plate was originally attached with heat to pin connectors. To reattach we suggest using glue. This U part attaches to the bottom of the console shifter bezel and shrouds the light. Check out our video on rebuilding your shifter below: ...

Fine scratches but great for the guy who wants original. The Reproduction does not have the II-DMI-6 lettering at the bottom like this original. You will have to carefully peel (roll back) the aluminum backing that is glued in place before gluing it in your mirror. If you use needle nose pliers and take your time it usually works fine. Note that the pictures of our 67-68 mirrors and lens can be deceiving. This is a tapered mirror, the narrow end faces upward on a Cougar, it is reversed when...

Left side Thermactor smog tube with the jog and bracket around the coil. Bare tube, installation hardware is not included. Not always available, hard to keep on the shelf, look for our reproduction tube set (right and left) available soon. Must have the correct cylinder heads with the drilled and tapped holes for these tubes. Also called air manifold, this unit is part of the air manifold assembly.

Right side Thermactor smog tube. Installation hardware is included as shown. Not always available, hard to keep on the shelf, we always have the reproduction tube set (right and left) in stock. Must have the correct cylinder heads with the drilled and tapped holes for these tubes.

Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. Tube dimensions 5/16" O.D. x 1.560" long. C6AZ-9A484-B

This tube is embedded into the cylinder head making it rather difficult to remove intact. Note that the nut and ferrule assembly is made of two pieces, with the ferrule being a compression fitting used to secure the smog tubes to a series of ports on the cylinder head. Sold individually, 8 total needed for smog installation. Application is 1967 - 1970 390, 427. 428CJ engines. In 1975 Ford started making these out of stainless steel. Tube dimensions 5/16" O.D. x 1.960" long. C6AZ-9A484-C

For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.

This is a 1968 only part that is correct for Cougars equipped with the 390 GT "S" code motor. Whether your Cougar has the GT package or not, as long as it has a 4V 390 motor, this is the correct snorkel for your Cougar. The internal dimensions of the opening at the air cleaner base end measure 4 1/8" X 2 3/16", the flange mounting holes measure 5 1/2" on center. The opening for the S tube is 2 3/4". Please keep in mind that our hard to find parts like this are not always competitively priced...

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Application small block 289/302/B302 all years 1967 - 1969 with factory Thermactor smog. Spacer for mounting cast iron air pump mounting bracket. Sized .75" O.D. x .73" long. *Note - On Cougars with factory air conditioning 1 spacer is used. On Cougars without air conditioning 2 spacers are used together.

C7SZ-3D600-A  Power steering pump adjusting spacer for use without air conditioning. For most 1967 - 1969 Mercury Cougar or Ford Mustang with 289, 302, 390, 428CJ engines, excludes 1969 351W and 1969 Boss 302 engines. Spacer dimensions: 7/16" I.D. x 1" O.D. and 1/2" thick. Same thickness as the pedestal bracket for air conditioning.

Used spacer for the lower windshield moulding