1968 Ford Mustang

NOS passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503136-B.

This is a core five piece set of front windshield mouldings for a 1967 - 1968 Mercury Cougar and Mustang (except fastback). These mouldings need restoration as they are dull, scratched and dinged. They would suffice to make a car complete if you were wanting to drive it but in our opinion they are a step below "good" driver quality. This set will not have any kinks, flattened out areas or holes, we discard mouldings of that description. We do not recommend the reproduction, "offshore"...

Used alternator bracket for any 1968-69 Mercury Cougar or Ford Mustang with 289 / 302 / 351W engine, but without factory smog pump.Replaces Ford part number C8OE-10156-A.*Trivia - the only difference between this bracket, and the C6OE-10156-A bracket is the thickness of the steel. Either one will work on 289/302/351W engines 1966-69.

Reproduction support brace to be used with 1967-70 Mercury Cougar and Ford Mustang export braces. Can be used with OEM, NOS or reproduction export braces. Contoured to match the curvature of the cowl.*Note - Will not fit early Shelby Mustangs.This part never came from the factory, but the idea was taken from the fact that Shelby cars had plates like these, though these are not interchangeable with Shelby export braces or export brace plates because of hole placement. The original Shelby part...

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang.  About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels. We won't always have the used in stock, but the reproduction version is very good.Replaces Ford part number C8MY-1424-A.

This is one of the best small block Ford V-8 books on the market. It covers 260-289-302 V8 engines. Carburetor numbers, distributor numbers, covers all engine brackets, pulleys, and parts of Ford small block engines. 100's of pages with pictures, casting numbers, and explanations by year. A must for concours detailing and year by year correctness. Author Bob Mannel, covers small block V8 engines and components 1962-69. References all Ford cars that these engines came in. Mustang, Cougar,...

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found in 1973 and newer Ford products, mostly F100 and Bronco.  These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: There are other versions of the Nodular iron third members. Non-"N", lazy "N", and square "N" this version. See related items.  Please have your desired date in mind when calling or place it in...

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found on cars with 427-4V, 428CJ, 429CJ, Boss 302, Boss 351, or Boss 429. These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available:There are other versions of the Nodular iron third members. Non-"N", lazy "N" like this one, and square "N". See related items.  Please have your desired date in mind when calling or place it in...

Used Nodular Iron 9 inch third member case, known as "N" - Case. typically found on 1968-69 Mercury Cougar and Ford Mustang with 427-4V, 428CJ, Boss 429, and Boss 302. These are the factory installed heavy duty third members typically with 31 splined axles. These are bare cases as shown. Current dates available: There are other versions of the Nodular iron third members. Non-"N" this version, lazy "N", and square "N". See related items.  Please have your desired date in...

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

OEM Style Transverse Resonator Exhaust Hanger 1967, 1968 and 1969 Mercury Cougar and Ford Mustang

Brightens the engine compartment and looks sharp. Fits our big block finned aluminum valve covers (item# 26018) and others with the round push-in style opening. Requires a rubber grommet to fit into the valve cover, which is usually included with new valve covers.Does NOT fit valve covers with the "stovepipe" fitting (like our small block finned aluminum units) or factory valve covers the tabs for twist-on oil caps. This cap is for after market valve covers.

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Oil filler cap elbow for hose that goes to the air cleaner elbow. Black plastic like original, fits 1968-70 Mercury Cougar and Ford and Mustang. See related items for grommet and other related parts.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

The oil filter made by the original Ford supplier.

New Old Stock oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Used oil screen pick up tube assembly from a FE or big  block 1966-70 Ford car, such as 352, 390, 410, 428, or 428CJ engine. This is for most front sump oil pans. Used item, should be degreased and cleaned inside and out prior to installation. Tube assemblies with damaged screens, damaged tubes or bends are thrown away or scrapped. We only save undamaged, used oil pick up tubes. Melling sells a quality reproduction of this item. Replaces Ford Part #: C6OZ-6622-A ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Replacement cork pan gasket for all 1965-73 C4 Ford transmissions. 

Used anti rattler board - 1/8" panel board that prevents rattling noise. Installs on top of fuel tank on the side where the jack and spare tire mount.Measures 12" X 6"

Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.

C7AE-6A666-B is stamped on this used PCV valve. Absolutely correct for 1968 390GT, 427-4V GT-E, and 428CJ Mercury and Ford cars. Must be used with either of the 90° elbows available, reproduction or OEM Ford.. This is used, no guarantee that it functions like new. Ford MPC number C7OZ-6A666-A. There is a published procedure for refurbishing these valves. These positive crankcase ventilation valve can be disassembled. ...

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

This adapter is threaded on bottom for Boss 302 / 390-4V / 428CJ PCV valve and 6 degree nipple on side. Gold Cadmium plated, not painted originally. This only works with the OEM or reproduction threaded PCV valves.Replaces Ford Part Number C7OZ-6A706-A.

Used brake shoe guide plate, or anchor pin, that holds the top of the drum brake shoes together on your Mercury Cougar or Ford Mustang equipped with drum brakes. For the money our reproduction plate is a better value and cleaner, too. These have 1/2 inch holes in them.Replaces Ford part number C4UZ-2028-A.

Used pinion yoke for an 9 inch rear end on any 1967-73 Mercury Cougar or 1967-73 Ford Mustang. 1310 U-Joint. Part cleaned for pictures, used parts shipped the way they come off of the cars. Shipped bare, no hardware included.Ford part number C3AZ-4851-L.

This rubber plug is found on the bottom side of 68 and 69 Cougars without tilt column. It covers the access hole for the bolt that removes the column head / collar. We notice that most cars do not have them in place. This could be due to over site at the factory or them being lost over the years as the car has been serviced. We have also noted that Dearborn cars rarely if ever have them present and San Jose built cars often have them in place. If you have a Dearborn built car and have this...

C6AA-3D746-A Oil cooler used on all 1968 Shelby Mustangs with power steering. Both GT-350 and GT-500 models. www.thecoralsnake.com/TRIVIA.HTML 2-3 items down.

This item will have a refundable core charge added to your order. Multi-year power steering pump, 1967-69, and 1971-73, excludes 1970. When fully assembled you will notice that this year P/S pump has a centered fitting for the pressure hose on the back of the reservoir. Most factory 1970 Mercury Cougar and Ford Mustang have an offset fitting. The only 1970 exception is the R or Q code 428 Cobra Jet engines, they used this pump. Manufacurers note: In place of the paper gaskets, it is...

Cylindrical shaped brass valve, some times called the pressure control valve or 'cigar' valve. Starting in 1968, disc brake cars have it mounted almost directly on the Pressure Differential Valve on the driver side fender apron. The pressure differential valve is also commonly called the 'brake distribution block'. We also sell our brake distribution blocks complete with the proportioning valves. The C8OA numbered proportioning valve started way late for the 1968 model year. We almost...

This plate attaches the 3/8" steel fuel line under the driver's side rear torque box, as it makes its way from the rear frame rail out to the rocker area. It acts both as a mount and as a protector from road debris. These were used on late 1967 to 1968 Cougars and Mustang with the 3/8" fuel line. Early 1967 cars had smaller 5/16" fuel line, and different routing (through the transmission tunnel), and did not use this part. Mounting bolts included.

Good used double sheave alternator pulley.Ford Part #: C5AF-10A352-J.

Reproduction alternator pulley, two sheave. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang and most all other 1965-73 Ford vehicles.

Ford part number C8AZ-6A312-A. Application 390-2V, 390-4V engines, and 428 Cobra Jet with air conditioning. Power steering optional, with dual alternator belts. Ford casting number C8AE-6312-A. Triple sheave 68 crank pulley.

1968 390-4V all with factory manual transmissions and factory air conditioning. Pulley diameter 5.89" inches. Ford part number casting # C8AE-9B480-B. Mounting bolts sold separate.

C8OZ-8509-C 1968 427 / 390-4V without air conditioning and 1968-1970 428CJ without air conditioning. Thermactor on all applications, power steering optional. 3 sheave pulley with two different diameters. The MPC lists it as 6 inches on the dual sheave portion and 5-1/16 inches on the outer but we find the actual outer most measurements to be 6 1/8" wide on the dual pulley and 5 3/16" wide on the single sheave pulley. When laid on a flat surface the height is 2 3/8" tall. Ford casting number...

Used FoMoCo 20 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and automatic transmission (code w). Used core radiator for recoring and restoration. Typical Dearborn installed assembly line radiator. Factory installed automatic transmission radiators came with the fittings in the bottom tank for transmission cooling. Current listing is dated 8FD or 4th week of June 1968. Very late production date.Replaces Ford part number C8ZE-8005-H1 ...

Used Western Modine (W/Mo) 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V or 302-4V engines and (automatic code W) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. This is the typical radiator installed at the San Jose, California assembly plant. W/Mo embossed on the top of the tank with a date. Dated 67-10 or October...

Used WMo or Western Modine 24 inch small block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 289-2V, 302-2V, or 302-4V and 3 or 4 speed manual transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Factory installed manual transmission radiators did not come with the fittings in the bottom tank for transmission cooling.Replaces Ford part number C8ZE-8005

Used 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical Dearborn radiator, only FoMoCo on the top tank. 1968 Mercury Cougar or Ford Mustang. Replaces Ford part number C8ZE-8005

Used WMo or Western Modine 24 inch big block radiator. This is for a 1968 Mercury Cougar or Ford Mustang with 390-2V or 390-4V and C-6 (automatic code U) transmission. Used core radiator for recoring and restoration. Typical San Jose installed assembly line radiator. Dated 67 12. Replaces Ford part number C8ZE-8005

These concours quality Chrome caps are made in America and bear all the original markings. O.E.M. details include original letter style, "S.M.C.O." and "Autolite". Pound rating is stamped on cap. Replaces Ford Part #: C7ZZ-8100-A.

New old stock Zinc radiator cap. Motorcraft stamped, with RS 12A, and 13# Pound rating is stamped on cap. Replaces Ford Part #: C9AZ-8100-A.

1968 Mercury Cougar AM-8 track Motorola manufactured radio. These will work and all wiring plugs will be present. Good working and tested radio, fresh installed 8 track belt, may have minor cosmetic issues from a past life. NOTE* The one radio we have in stock at the moment has working AM, all buttons work, but the 8 track tape will not stay in position and needs fiddling - Call for advice. *NOTE* Does not include brackets or knobs. Ford master part # C7WA-18806-A, Chassis and Escutcheon...

F8TBZ Mercury Cougar and Ford Mustang AM/FM stereo radio. Grade "A" condition guaranteed to work well. When you adjust for inflation these radios are actually less expensive now than in the day! 1968 was the first year for a AM-FM true "Stereo". 1967 was mono-stereo. Bendix was the original manufacturer of AM/FM radios in 1968. *HELPFUL HINT* 1968 and 1969 AM/FM radios are virtually the same except for the shaft lengths. Installing a 1969 AM/FM radio in your 1968 Cougar or Mustang with factory...

F8TBZ Mercury Cougar and Ford Mustang AM/FM stereo radio. This is a non-working unit that has a good crystal and knobs. All knobs seem to move freely. When you look inside the cooling holes on the top of the case you can see mouse droppings. Good unit to use for a modern upgrade core or good for restoration. Are you going to install this unit yourself? The first issue of Legendary Cougar Magazine has a great how to article that will help you in your journey to musical bliss. You can get...