1968 Ford Mustang

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Used wheel cylinder link pin. This pin protrudes from both ends of the wheel cylinder and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Fits all drum brake wheel cylinders, front or rear drum brake systems. Two needed per wheel cylinder. Sold individuallyFord part number B7A-2042-A.

Reproduction wheel cylinder link pin. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place. Sold individually. Ford part number B7A-2042-A.

Reproduction set of wheel cylinder link pins. These pins protrude from both ends of the wheel cylinders and are responsible for moving the brake shoe in and out when pressure is applied as well as keeping the brake shoe in place.Sold as a set of four.

Latch rod that links the door latch and the inside door handle, right or left side door. 1968 Mercury Cougar and Ford Mustang door latch rods are straight, and do not have a clip midway, compared to the 1967 version. Normally this rod was fabric covered. Used rod only, no retaining end clips. Replaces Ford part number C8ZZ-6521940-A. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click...

Manual control shift linkage assembly for a floor shift C-4 transmission in any 1967-68 Mercury Cougar or Ford Mustang.  Check out this video

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Linkage arm that attaches to the windshield wiper motor that is unique to the 67 - 68 Mercury Cougar and Ford Mustang. These are marked 7Z, among other things the slot is specifically indexed for the 67 - 68 Cougar and Mustang application. This is basically an installation kit that includes: linkage arm, flat bushing, wave washer, and nut. The order of installation is flat bushing, wave washer, linkage arm, and lastly the nut.

Includes two door lock cylinders, two door cylinder gaskets, two keys and one ignition lock cylinder.  Made by the original OEM supplier.  That being said, they do not make them like they used to. Replaces Ford part # C7AZ-6222050-A or C9AZ-6222050-A.

*NOTE - These knobs are NOT in the original Ford packaging, they were bought in bulk from a supplier who did not provide packaging. This style of knob was used on almost all Ford products starting in 1968 and continuing on through the late 1970's. The latest renditions in reproduction form are actually pretty good but for the purist these make a nice touch. Paste the part number into the Ebay search box and sometimes you can get lucky and get a pair for under $30. Limited supply, original...

Exact replacement inside door handle nut, trunk lock nut, and hood scoop nut. Same finish as originals. 10 of these are used to mount the 68-71 hood scoop found on the 68 428 CJ, 69-70 Eliminator, 69-70 428 Ram Air equipped Cougars and 71 GT and 429CJ. Two of these per door are used on the 69-70 inside door release. Two of of these nuts used to attach 1967-68 Cougar trunk locks.

Correct style nut with captured washer for attaching hood scoops, 1969-70 Mercury Cougar inside door handles, and 1967-68 trunk lock. Correct nuts would have been black phosphate, these are shiny gold as shown.

Used original driver side (left hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522135-A.

Used original passenger side (right hand) key lock to latch door lock rod for the Mercury Cougar or Ford Mustang.Ford part # C7ZZ-6522134-A.

[No Description Provided]

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This is a rebuild service in which we will replace the locking pawl and cable. We provide this service for Cougars, Mustangs and T Birds.Ford part number C9ZZ-3E520-A THIS SERVICE REQUIRES THAT YOU SEND IN YOUR CABLE IN ADVANCE.

New manufactured Tilt / Tilt-Away cable for any 1968-69 Mercury Cougar or Ford Mustang with factory tilt steering column. All new parts developed by our in house steering column expert DW. Not created from used parts. The cable sheathing will not split or crack over time like the originals.Replaces Ford part number C9ZZ-3E520-A*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way...

Keep in mind we can repair these for half or less of the price we charge to sell one outright. We can also install parts and or refurbish these columns. Ford part number C9ZZ-3E520-A *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory C code 289-2V V-8 engine. Rated at 195 Hp with 8.7:1 compression ratio in 1968. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, distributor, accessories, pulleys, and flex plate. Intake manifold and oil pan are included...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory F code 302-2V V-8 engine. Rated at 210 Hp with 9.0:1 compression ratio in 1968. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil pan are included but oil pan...

Short rubber valve stem and cap for Ford wheels or any steel wheel with a 0.453" hole. Snap in style, sticks up 2 inches from wheel surface. These will work with all of our aftermarket Ford wheels especially with trim rings. These have the Dill 627 caps. Same as the 1960's cars.

375897-S White plastic 5/16" washer for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 2 per side, sold individually.

This part is installed on all XR7 fuel sending units and Cougars and Mustangs with the optional Convenience Control Package. Low quality off shore part that requires soldering to your fuel sending unit. This is a temperature sensing device that activates when the fuel level drops enough to expose the unit at which point the circuit is closed and the low fuel light comes on. Commonly referred to as a Thermister / Thermistor / Low Fuel Sending Unit.

Fits the 1967, 1968, 1969, 1970 and 1971 Mercury Cougar with the 390, 428, 428CJ, 428SCJ, 429CJ or 429SCJ. Replaces Ford Part #:C8OZ-7B535-AR

Rebuildable Core grade lower control arm for any 1968-69 Mercury Cougar and Ford Mustang. These are wearable items, and we list this item for those folks who really wish to go 'Concours trailered'. These interchange from side to side, two per car. Fits other 1968-69 Ford cars such as Torino and Cyclone. Even though these are select parts, we recommend that the ball joints and bushings be replaced.  Anghel Restorations can rebuild 1964-73 Ford suspension components to...

Reproduction reinforcement plate designed to weld onto the lower control arms. Sold individually, we are not sure that you would want to even buy one of these. They don't fit very well, and are not contoured to any lower control arm on the market. You will be bending these to fit, prior to welding. *Note - This is a non-returnable item. 

This is an economy version of the lower control arm assembly, with a spot welded on "heavy duty" reinforcing plate. Yes, this is the same "heavy duty reinforced" lower control arm assembly carried by the other parts vendors. We are sorry, but we just cannot recommend this part. The Scott Drake premium version (Part #:26709) of this lower control arm is far superior and basically the same costs. In the picture, you can tell that it is lacking a rolled lip on the outer edge that...

You can use 1968 up to 1973 lower control arms on a 1967 only if you change the strut rod to the 1968 - 1970 style. We have the strut rods available in both new and used form. Replaces Ford part #: C8OZ-3078-A. Sold individually, right is the same as left. *NOTE* The Cougar only, 1967 only, lower control arm is not available in reproduction form but you can rebuild the originals so do not throw away your cores as they may prove to be valuable one day. Mustang never used the articulated strut...

Sold individually, right is the same as left.  NOTE* You can use the 1968 - 1973 lower control arms on a 1967 ONLY if you change the strut rods to the 1968 - 1970 style. We have the strut rods available in both new and used form. Find them here. Replaces Ford part # C8OZ-3078-A. Check out this video ...

Reproduction adjustment cam / bolt for the lower control arms of the Mercury Cougar or Ford Mustang. We also offer this used version as well. These units are sold individually.Ford part # C6OA-3B236-A.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 9/16 across the leading inside edge, and 1 5/8 across the outer rim.Note: These larger diameter bushings were used on Ford service replacement lower control arms. Typically found on Ford supplied lower control arms without the welded on jacking tabs.

Set of two polyurethane bushings that insert into the rear side of the lower control arm. This set contains two bushings that measure 1 7/16 across the leading inside edge, and 1 5/8 across the outer rim. Typically these bushings fit Ford factory installed lower control arms with the welded on jacking tabs. Note: These smaller diameter bushings were used on factory installed control arms. Service replacement control arms utilized 1-9/16 inch bushings.

Reproduction Lower Headlight Bucket Loom Clip for the 1967 - 1968 Mercury Cougar - 1967 - 1968 Ford Mustang 

Used only in 1968 on non xr7 models and Mustang. Very hard to come by with no splits, burns or cracks. We rarely can supply the color you desire but please let us know your desired color and we will try. Grade A will not have UV ray damage and will look right at home in a low mile car. Satisfaction guaranteed.  

Used only in 1968 on non xr7 models and Mustang. Very hard to come by with no splits, burns or cracks. We often can supply the color you desire, please let us know your desired color and we will try. Grade B will need to be repainted and will not be as soft and straight as grade A. The simulated stitching embossed in the vinyl may show areas of slight separation.

This pad is in poor condition. You can actually modify a automatic pad to work with your manual transmission chrome bezel. *NOTE* If you have a clean example of this pad for sale we would like to hear from you!

Found on the lower radiator core support. 2 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 377359-S.

Found on the lower radiator core support. 2 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 377359-S.

4 oz. tube of non-melting, water resistant grease for disc and drum brake hardware, hood hinges, window regulators, quarter windows, vent window hinges, pretty much whatever needs lubing. A little dab will do ya!Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

Reproduction BLACK lug nut fits all Legendary Series wheels. 14mm x 1.5 threadSold individually. 

Chrome tapered acorn lug nut for use with the new Legendary wheels. This 13/16" nut really only fits the Magstar style - the others have tighter clearances and you'll want to use the 3/4" nuts made for these wheels. Sold individually here, or in a complete set with valve stems. Replaces Ford Part #: C9ZZ-1012-B.Check out our video on Legendary Wheels below: ...

Correct 3/4" tapered chrome acorn lug nut for the new Legendary Wheels. These are what we recommend you use with these wheels, since the clearances are too tight for regular 13/16" lug nuts. Sold individually here, or as a complete set with valve stems.Check out our video on Legendary Wheels below: ...

Reproduction lug nut for the Legendary GT7 Series wheel. Sold Individually. You can find the complete lug nut installation kit here.Check out our video on Legendary Wheels below: ...

Chrome acorn lug nut for most any Ford steel wheel including styled steel, Magnum 500,  new or reproductions.Replaces Ford Part #: C9ZZ-1012-B.

Standard stamped steel wheel lug nuts in good used condition. 1/2"-20. Need to replace missing, cross threaded, or otherwise damaged lug nuts? Do you have after-market chrome wheels with the flat washers and closed round head lugs? Fits the following models with stamped steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar Should have a set of 5 in the trunk for use with your stock steel spare...