1968 Ford Mustang

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Stainless steel throttle pedal surround trim. Self attaching to part number C5ZZ-9735-E. This used part may have some wear, but will not have broken tabs. Fine steel wool really shines these up.Fits 1967-68 Mercury Cougar and 1965-68 Ford Mustang.

Restored drive side upper windshield moulding, fits all 1967-68 Mercury Cougar and 1965-68 Ford Mustang coupes.Ford part number C5ZZ-6503145-B.

The trim at the top of the windshield on the left hand side.Ford part number C5ZZ-6503145-B

NOS driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503137-B.

Your original decades old trim will look fine... Until you place it next to a quality paint job.Ford part number C5ZZ-6503137-B.

Used driver side (left hand) vertical windshield moulding / trim for the Mercury Cougar or Ford Mustang. These are suitable for restoration and for use your daily driver.Ford part # C5ZZ-6503137-B.

This restored OEM stainless steel lower windshield moulding / trim has been restored to a level far beyond NOS. It has been polished to a mirror like finish that is brilliant and gleaming. The term "over restored" could be applied to this part because back in the day FORD never spent the time we invested into polishing this piece. Original parts like this one always fit and look superior to "offshore" reproductions.Ford part # C5ZZ-6503148-B.

This good used original lower windshield moulding / trim has been carefully inspected to be free of small dings and heavy scratches. It will have very light scratches consistent with a classic of this age but nothing a do it yourself type could not bring to show quality on his own. This trim piece is perfect for someone wanting a trim part ready to install on their very nice driver or occasional show car. Much better fit than "offshore" reproductions. Ford part # C5ZZ-6503148-B. *NOTE* Keep in...

NOS passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. Ford part # C5ZZ-6503144-B. 

Restored passenger side (right had) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will look right at home gleaming in the sun on your mint condition Cat or Pony and will definitely make your ride POP!Ford part # C5ZZ-6503144-B.

Used passenger side (right hand) upper windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece is suitable for your lower quality daily driver or a great piece for a high quality restoration.Ford part # C5ZZ-6503144-B. 

Restored passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece is considered over restored because of the high luster and will make your Cat or Pony absolutely POP!Ford part # C5ZZ-6503136-B.

Used passenger side (right hand) vertical windshield moulding / trim for your Mercury Cougar or Ford Mustang. This piece will fit right in on your daily driver or is an excellent candidate for those of who like to restore your own parts.Ford part # C5ZZ-6503136-B.

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

Restored five piece windshield trim set has been restored beyond the original luster. Keep in mind only cores with minor dings, dullness and scratches can be accepted. Kinked, gouged, and flattened cores will not be credited. This windshield moulding set fits the 1967-1968 Mercury Cougar as well as the 1964 1/2 - 1968 Mustang Coupe and Fastback. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* If...

Good used five piece windshield moulding / trim set as taken from a parts car. Finish will be dull and some pieces may have minor scratches, but overall, this set is ready to install and will look decent as is. Ford part numbers for these pieces include: C5ZZ-6503136-B, C5ZZ-6503137-B, C5ZZ-6503144-B, C5ZZ-6503145-B, and C5ZZ-6503148-D. *NOTE* Keep in mind we will buy most moulding / trim found on the Mercury Cougar. ...

Reproduction sway bar mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Original driver side sway bar mount for your 1967- early 1968 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions of this bracket were used starting in 1968. This version has a straight cut edge on the front section, later versions were curved. Straight and curved mixed during 1968 on same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as:...

Original driver side sway bar mount for your LATE 1968-70 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions available in 1968. Both curved and straight cut, even on the same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, this is the driver side only. See related...

Reproduction sway bar clamp mount for your 67 - 70 Cougar or Mustang. Close to original design, but misses by a mile. Does not share the correct contour as originals. Welds to the front frame rail.

Original passenger side sway bar mount for your 1967- early 1968 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions of this bracket were used starting in 1968. This version has a straight cut edge on the front section, later versions were curved. Straight and curved mixed during 1968 on same car. Original part number is 5A483. The MPC and other manuals refer to this...

Original passenger side sway bar mount for your LATE 1968-70 Mercury Cougar or Ford Mustang. Nice original, removed from our better cars. Metal cleanup needed, we cut these a little generously to protect the bracket. Two versions available in 1968. Both curved and straight cut, even on the same car. Original part number is 5A483. The MPC and other manuals refer to this bracket as: reinforcement and mounting bracket for front stabilizer bar. One per side, this is the passenger side only....

For all 1968 Cougar trunks to mount the spare tire. Total length according to the MPC is 9.75 inches, with 4 inches of threads on the end. We have found that the overall length is 8 inches with 3-1/4 inches of threads. Basically the same J- bolt as found on 1967 Mercury Cougars but with the thicker, 1/2-13 threads. As we research more we will post our results here. Would love to get specs on J-bolts from those of you with low mile and very original cars.

Three required per car, held in place by Allen head bolt, fits in the three slots at the top of the column tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.Fits: 1968 Mercury Cougar1969 Mercury Cougar 1968 Ford Mustang1969 Ford Mustang ...

Used cast iron pedestal mount for the A/C compressor for Cougars and Mustangs produced after 1/3/1967. This bracket was utilized throughout the entire 1968 model year and is also listed as the service replacement part for the early mounting bracket.  Ford part # C7AA-2882-L, MPC # C7AZ-2882-G.

Cast iron pedestal mount for the air conditioning compressor on all 1967 and 1968 cars with 390-2V, 390-4V, or 428CJ FE engines. Mercury and Ford master part number C7ZZ-2882-A, we suspect that this is an error in our 1975 editions of the MPC's. C7SZ-2882-A is what we suspect is the correct number. In any case, C7SA-2882-A is the factory casting number on these brackets.Below are some pictures of a 390 with AC and smog. This motor was pulled from a 1967 Thunderbird, so there are a few minor...

Used alternator mounting bracket for any 390 / 428CJ engine without smog. This is the correct bracket and was found on 1968 390-2V or X-code Mercury Cougar and Ford Mustangs. 1969 390-4V or 390IP engines in any Mercury Cougar or Ford Mustang. If you aren't a concours person or care about correctness, this alternator installation style is the cheap way to go if you aren't planning on installing the thermactor smog components. Look in the related items list for the adjusting bracket and...

Cast iron construction similar to the 1967 bracket but made to fit the 1968-1970 style smog pump with 3 bolt pulleys. Ford part number C8AZ-9B450-B, casting number C8OE-9B450-A. Mounting hardware sold separate.

Driver side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog. Ford Part Number C8OZ-2B293-A Check out this video Check out our caliper tips and tricks video below: ...

Passenger side caliper mounting bracket, also called a caliper anchor bracket in the Ford Master Catalog. Ford part # C8OZ-2B292-A Check out this video Check out our caliper tips and tricks video below: ...

This is a much higher quality bracket than other reproductions. Correct texture and fit. The bracket offered by most companies is just pot metal sprayed gray. Replaces Ford Part #: C7SZ-3A732-B or C7ZZ-3A732-B.

Original FoMoCo used part in good condition. Casting number is C7AA-3A772-B. Fits both small and big block. This is really the way to go... Original OEM FoMoCo with all the right markings and about half the price or repro. Ford Part #: C7ZZ-3A732-B.

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Available in correct OEM Black. customers looking for a little more flash under the hood might be interested in the highly-polished stainless steel version of this bracket! Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

These Brackets are made from stamped steel just like the original, and built to Ford specifications for an exact fit. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on Radiator and Fan upgrades below: ...

When you compare the originals to the reproductions you will see minor differences. This is one of the first things you look at when you open the hood of your car. For those that are looking to keep their car original, investing a little elbow grease in clean up on these used brackets is the way to go. Consider adding the upper rubber pieces to your order, see related items.Not for use on 17-20" wide standard cooling radiators. Replaces Ford Part #: C7ZZ-8A193-A. Check out our video on...

This special bracket gets glued to the windshield. Rear view mirror bracket gets mounted to it. Glass bead blast it or just use a wire brush and it is ready to go!

Reproduction thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Painted Ford engine blue a shown. Nice reproduction, made in the USAFord part # C8AE-9C486-A.

Thermactor smog anti-backfire valve canister mounting bracket. For all 1968 390GT engines, GT-E 427-4V engines, and 1968-70 428 Cobra Jet engines. Ford part # C8AE-9C486-A. *RESTORATION TIP* This bracket was painted Ford Engine blue from the factory.

Metal-stamped 1968 - 1970 Lower Radiator Mounting Brackets feature exact detail and proper fit. Painted dull black. Sold in Pairs. Rubber insulators not included. Replaces Ford part # C8ZZ-8052-A. Check out our video on Radiator and Fan upgrades below: ...

Our used lower cradle brackets for the 24" wide radiator will always have some amount of damage as shown. We will not send you mangled junk that is heavily rusted but they will require some amount of straightening due to their vulnerable location. These also work with the 67 small block and big block when putting in a 68-70 24" radiator but keep in mind the 1967 cars are not pre-drilled as are the 1968-1970 Mustang and Cougar.We are out of the 1970 style of brackets. We only have the two...

Concours correct reproduction of the front sway bar clamps used on all 67 - 70 Cougars and Mustangs with the competition suspension option, or 15/16th" sway bar. Never available until now. Exactly like the originals in every detail. Standard for all Shelbys, Boss 302s, and Cobra Jets. Stamped and formed just like the originals.

Repro fuel pump gasket for 1967 - 1970 Cougars or Mustangs with 289/302/351W/390/428CJ engines.

Used on the lower mounts on the 67 - 70 big block and small block 24" wide radiator. A 1967 390 with the original radiator uses a different lower mount system which uses a different sized insulator. If you are updating your 67 with a 68 radiator you will need these. Sold as a pair. Replaces Ford part #: C8ZZ-8125. Check out our video on Radiator and Fan upgrades below: ...

Sold as a pair, fits well into your upper radiator bracket used on 24" radiators 1967 - 1970. Replaces Ford part #: C7OZ-8124Check out our video on Radiator and Fan upgrades below: ...

This kit includes the 4 fine threaded "T" shaped studs (with nuts) that mount the backing plate to the spindle and the plate that goes on the inside of the backing plate. These are used parts that are not damaged or corroded, taken from a Western parts car.