1968 Ford Mustang

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

We rarely have extras of these in stock but we like to show these items so you know what you are looking for or you can use it as a visual and fabricate your own kit. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice.Also available as a reproduction mounting kit. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them. ...

Reproduction booster to firewall installation kit for the 67 - 68 Cougar or Mustang with the Midland Booster.

Concours Correct low head carriage bolts and flange nut fastener kit for the 67 - 68 Cougar and MustangOne kit does both shock tower covers

Nut for attaching brake boosters in any 1967-73 Mercury Cougar or Ford anything, including Mustang. 3/8 - 16 zinc plated nut with serrations.

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads.  3/8-24 threaded nut, serrated washer head style. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Replaces Ford part # 55806-S

Reproduction pair of mounting nuts for any 68 - 70 Cougar or Mustang with power brakes.

Used mounting plate for the heater blower motor on the 67 - 68 Cougar or Mustang without A/C.

Spare tire, with styled steel wheel hold down disc. Fits all 1968-70 Mercury Cougar and Ford Mustang. Original Ford part number C8MY-1424-A. About 3 inches in diameter, this is the specified trunk hold down plate for the use with the factory mag wheels.

Sold individually. Phosphate & Oil (gray-black)

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

C5AZ-10A370-C Alternator mounting spacer, goes between the cylinder head and alternator housing. Fits 1968-70 390-2V, 390-4V, and 428CJ engines. Smog OK. There is no casting number but one is listed C5AE-10A370-C. Inside diameter 7/16". We measure them out at 1-5/8 inches long, supposed to be pink anodized or tinted.

Steel spacer between cylinder head and pump. Inside diameter 3/8", length approximately 1-13/16".

1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)

10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).

The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...

This gasket seals the fresh air tube in the cowl to the heater box inlet on 1967 through 1970 Cougars.

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

[No Description Provided]

Replaces Ford Part # 381985-S Sold individually

Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...

Special nut with large diameter spinning washer for the set screw for the door glass adjustment. Sets and holds your door glass angle to allow a proper seal. Three set screws work in conjunction for each door glass and vent window combination. See your shop manual for actual procedure.See also 378696-S for the vent window and front door channel set screws.Ford part number 33797-S.

Reproduction exhaust pipe to exhaust manifold nut for the Mercury Cougar or Ford Mustang and they are sold individually.Ford part # 376420-S.

Reproduction nut that replaces Ford part # 34033-S. This is the nut that secures the pitman arm to the steering box. Has correct 7/8"-14 threads. Split washer also needed, not included, nut only.

This is our reproduction quarter panel extension nut for the Mercury Cougar or Ford Mustang. Sold individually.Replaces Ford part # 373556-S.

Replaces Ford part # C2DZ-6A529 Sold Individually.

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

New 3/8-16 nut for the shock tower shock cap. Three nuts used on each cap, 6 total per car. Sold individually.Replaces Ford part number 377706-S7.

Perfect fit.

Correct nut that is designed not to come undone.

New torque converter nuts for connecting torque converters to flex plates on 1967-73 Mercury Cougar or 1967-73 Ford Mustang or other Ford Lincoln Mercury that is not metric. 3/8-24 threads, Grade 8 nut with a 9/16 inch hex. 0.79" OD and 0.39" thick. Torque converters use 4 nuts for attachment.Ford number 377704-S

34392-S7 5/16 inch nut for 1967-68 Mercury Cougar and Ford Mustang vent window pivot assembly. 1 per side.

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut/ one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube. New Old StockFord part number C8OZ-9B471-A.

Application is 1968 289-2V, 302-2V, and 302-4V all with manual transmissions. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut/ one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS service replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

Nut and ferrule assembly for thermactor smog tubes. Sold individually, 8 per car with V-8 engine. This is a NOS replacement nut and ferrule that is one piece. Fits thermactor equipped cars from 1967-71. Including 1967 cars with California emissions, 1968 manual transmission cars, 1968-71 Ford cars with factory Holley carburetors, etc. Several Ford part numbers for this item C7AZ-9B471-A, AND D5TZ-9B471-A, C6AZ-9B471-A,C8OZ-9B471-A.

380771-S100 Good original used nut and washer for mounting all pitman arms. Has correct 7/8"-14 threads. Ford master part number for the washer is 34814-S.

Set of 4 reproduction torque converter nuts for the Mercury Cougar or Ford Mustang.

Used set of four nuts and two locking washers used on the knob shafts of all radios 1967 - 1973 used on Cougars, Mustangs, Galaxie, Torino etc.

Nuts and washers for attaching the rear differential carrier or pumkin or third member to the rear axle housing.Correct for all 1967-68 Mercury Cougar and 1965-68 Ford Mustang. 8 inch or 9 inch third members, all the same.

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.