Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Used plastic clip for the Mercury Cougar or Ford Mustang.
Used plastic clip for the Mercury Cougar or Ford Mustang
Used plastic clip for the Mercury Cougar or Ford Mustang. Cougar owner Mike B. shares that this clip was also used on 1970 Cobra Jets with Drag Pak option. Used to hold the wiring harness behind the factory oil cooler on the radiator core support.
Used wire loom plastic clip for the Mercury Cougar or Ford Mustang
Partially dipped clip for attaching the seal on top of the radiator core supports. Often times with air conditioning the seals were installed. The factory sometimes used staples, sometimes clips. You would have to investigate your core support for staple holes. 5 clips are typical for attaching the seal. Spread them apart to where it looks equal. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. ...
This is the speedometer cable clip that connects to the firewall and transmission tunnel. Replaces Ford Part # : 373829
New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually. Replaces Ford part number 382929-S.
Found on the lower radiator core support. 4 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 382350-S.
Windshield washer hose clip that holds the hose up under the cowl. Concours quality, made right here in the USA.
This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.
This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.
Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S
Clips that attach to the dash for mounting the defrost nozzles. Package of 4 clips and 4 nuts, enough for non air conditioned cars, same clips used for air conditioned cars. Cars with A/C only need 3 clips installed though. Nuts are different than OEM, but work fine, we suggest adding a flat washer though.
Clips or clamps for attaching the 3/8" hard fuel lines to the body of any 1968-73 Mercury Cougar or Ford Mustang. Clips only, save your attaching body bolts. Sold in packages of 4 clips as shown. Will work on 1967 cars if you change to 3/8 lines. 1971-73 Cougar owners can use item 27565 attaching bolts, they are the same as the fuel tank mounting bolts. See related items. Replaces Ford 354663-S8
Set includes ten rectangular clips with pop rivets and two incorrect, irregular shaped end clips (Mustang Part). These clips will fit the 68 Cougar, but are actually replicas of the clips for the 67-68 Mustang. Rather than the plastic end clips in this kit, we recommend the metal version that we sell separately. NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to...
Fits 1967 and 1968 Standard or XR7
Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.
Prepare to be disappointed... This is a reproduction 1967 - 1968 Ford Mustang clock knob and set screw (replaces Ford part # C7ZZ-15032-A) that can be cut down to work on your 67-68 standard Mercury Cougar (barely). The pictures below will guide you on this "adequate at best" solution for those of you missing this hard to find knob and set screw.Click on images to enlarge. The above picture is a good used original Cougar knob mounted on a 68 clock. We do not have these original Cougar...
Reproduction thermal fan clutch that fits 1967 - 68 289 engines, 1968 302/390/427/428CJ engines, and 1969 351W engines, all with original Ford thermal cooling fans. Slightly larger in overall diameter, (still fits fine), and retains the correct spacing from radiator. We know that these will fit Mercury Cougar and Ford Mustangs 1967-69. Closest reproduction fan clutch on the market that fits the original and reproduction C8OE-B 7 blade power fan. Hayden fan clutch with an overall height of 2.98...
C8OE-8A616-B 1968 Thermal Fan Clutch - Used C8OE-8A616-B For all 1968 - 289/302 engines with air conditioning (Fan marked C6OE-G), and all 1968 - 390/427-4V/428CJ engines without air conditioning (Fan marked C8OE-B). This fan clutch can be marked C8OE-B or C8OE-C, on the hub. Ford part number C8OZ-8A616-B. Good used unit, we are unable to warranty these units. We will try to list the exact markings as they come in.
(7521) The attaches to the bottom leg of your equalizer bar and the pointed end fits into the recess of your clutch fork. Replaces Ford Part #: C7ZZ-7521-L.
Economy version of the clutch adjusting rod that fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.
Reproduction premium adjusting rod which includes: 2 Lock Nuts 1 Spacer 1 Retaining Clip Fits the 1968, 1969, and 1970 Mercury Cougar with the 390GT, 428CJ or the 428SCJ. Replaces Ford Part #: C8ZZ-7521-BR. Can be used on 1967 3 or 4 speed cars with 390 engine, but must use the 1968 clutch fork, see item 13882.
New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A
This set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling. Replaces Ford part #: C5ZZ-2979.
Equalizer bar or "Z" bar for small block engines with a manual transmission. Both 3 and 4 speed manual transmissions. Replaces Ford part number C7ZZ-7528-G.
Nice reproduction of the original. Street name is Z-Bar. For all 1967 - 1970 FE engines 390 and 428CJ. Replaces Ford part #: C7ZZ-7528-B.
Clutch equalizer pivot mount, engine side. Zinc plated. Replaces Ford part #: C7ZZ-7A572-BR.
Mounts on frame for equalizer bar to ride on. Replaces Ford Part #: C5ZZ-7507-A.
Replaces Ford Part # : C7ZZ-7507-B
Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C8OZ-8600-A. This fan will also work on many small block applications. We hope...
C5OZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long. Specifically used with a 157 tooth flywheel, as opposed to the 164 tooth fly wheel used after Feb 1968.Replaces ford Part # C5OZ-7515-B. Cougar before 2-15-1968, 289/302 Engines. Mustang before 2-15-1968, 289/302 Engines. *Note - This style of clutch fork uses the 'wire' for the holder, not the clip. ...
C5OZ-7515-B Manual transmission clutch fork for small block V8 engines - 3 and 4 speed, stick shift transmissions. Fork measures 9-1/4 inches long from the divot where the rod rides to the tip of the forked end. Specifically for the C5DA-6394-A bellhousing that used a 157 tooth flywheel. Cougar 1967 through 2-15-1968. XR7, XR7-G. Mustang 1965 through 2-15-1968. 2+2, GT. Fairlane 1965 through 2-15-1968. 500, XL, Custom. Torino / Ranchero 1968 through 2-15-1968. 500, XL Comet 1965 through...
C8OZ-7515-A Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 10-1/2 inches long. Specifically used with a 164 tooth flywheel, as opposed to the 157 tooth fly wheel used before Feb 1968.Replaces ford Part # C8OZ-7515-A, alternate number C8OA-7541-A. Cougar after 2-15-1968 - 1969, 289/302 Engines. Cougar 1969, 351 Engines. Mustang after 2-15-1968, 289/302 Engines. Mustang 1969, 250/302/351 Engines. Fairlane after 2-15-1968,...
C8OZ-7515-A Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 10-1/2 inches long from the divot where the rod rides to the tip of the forked end. Specifically used with a 164 tooth flywheel, as opposed to the 157 tooth fly wheel used before Feb 1968. Replaces Ford part number C8OA-7541-A. Ford casting number C8OZ-7515-A. New reproduction small block fork also available here. Cougar after 2-15-1968 - 1969, 289/302 Engines. Cougar 1969, 351...
C8OZ-7515-B Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number C8OA-7541-B. Cougar after 2-15-1968 - 1969, 390 Engines. 390IP. Mustang after 2-15-1968 - 1969, 390 Engines. 390IP. Fairlane after 2-15-1968, 390 Engines. Torino / Ranchero after 2-15-1968 - 1969, 390 Engines. Comet after 2-15-1968 - 1969, 390 Engines. Montego after 2-15-1968 - 1969, 390 Engines. ...
Replaces Ford part number C8OZ-7515-D. Manual transmission clutch fork - 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number C8OA-7541-D.
C8OZ-7515-D Manual transmission clutch fork - 4 speed, stick shift transmissions. Fork measures 12 inches long. Alternate number C8OA-7541-D. Cougar 1968 - 1969, 428 Cobra Jet engines. Mustang 1968 - 1969, 428 Cobra Jet engines. Fairlane 1968 - 1969, 428 Cobra Jet engines. Torino / Ranchero 1968, 428 Cobra Jet engines. Montego / Cyclone 1968 - 1969, 428 Cobra Jet engines. *Trivia - This fork originally had a blue paint mark for identification purposes. This model clutch fork...
Used until early (prior to 2/15/1968) on manual transmission cars. Comes with rivets. Replaces Ford part #: B9AZ-7522-B.This style uses the early clutch fork with the anti rattle wire.
Clutch Fork Pivot for Cougars manufactured after 2/16/1968. Replaces Ford Part #: C8AZ-7522-A.
Manual transmission clutch kit for all 1967-73 Mercury Cougar or Ford Mustang with 3 or 4 speed transmissions and 289, 302, or 351 engines. This is a 10 inch disk, pressure plate, throw out bearing, pilot bearing, and alignment tool. The clutch disc is asbestos free.