1969 Ford Mustang

This is a mirror nut bezel tool used to remove the mirror nut on the 1967 - 1968 and 1970 - 1973 Cougar. No more scratches trying to remove with the wrong tools. These are made from HRS steel and are milled to fit the bezel nut. This tool pays for itself each time you use it. NOTE: This is an exact fit for ALL used mirror nuts (bezels) and the 1970 - 1973 reproduction mirror nuts (bezels). However, you will find it does not fit our 67-68 repro mirror nuts (bezels) and will need some...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch and wiper switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1969 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

Sold individually Zinc (dark silver)

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.

Nice quality hardware for attaching the shift rods to the bottom of the shifter mechanism. Won't work with the 1970-73 Hurst shifters, but does work with all of the others. Including 3 speeds, sorry, sold in packages of 3 though. Check out our video on rebuilding your shifter below: ...

Reproduction passenger side (left hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

This is a reproduction 3 piece non assembled torque box for the driver side on the 69 - 70 Cougar or Mustang Coupe. The benefit of getting a non assembled torque box is that you'll find installation much easier as compared to the pre-assembled boxes.  Included are inner and outer panels and gusset. Passenger side non-assembled torque boxes are not available.

Here is our reproduction SPI torque box for the driver side (left hand) of your Mercury Cougar coupe.

Here is our reproduction passenger side (right hand) SPI torque box for your Mercury Cougar coupe.

Reproduction torque box gusset for your 67 - 70 Cougar or Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box for extra strength. Sold as a pair.

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.

Rebuilt C4 24 spline torque converter for the 1967 - 68 Mercury Cougar or 1966 - 69 Ford Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. Ford part number C6AZ-7902-M. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of...

Rebuilt small block C6 Ford transmission torque converter for the 1971-73 Mercury Cougar and Ford and Mustang. 31 splines and 1.375" Pilot diameter. This item carries a $200 core charge, refundable when we receive your rebuildable core. Fits small block C6 transmissions, typical for 351C engines and others when equipped with "U" code transmission and H, or M code engines 1971-73. Has 11.5 inch circle diameter for the flex plate studs, Ford part number D1AZ-7902-A....

Rebuilt C6 FE Engine torque converter for the 1967 - 70 Mercury Cougar and 1966-70 Ford and Mustang. 31 splines and 1.848" Pilot diameter. This item carries a $200 core charge, refundable when we receive your rebuildable core. 1966-70 Ford FE engines include: 352, 360, 390, 427, 428, etc. Ford part number C8OZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It...

NOS Autolite 4300 training handbook. Filled with details pertaining to operation, adjustments, overhaul and servicing of the Autolite 4300 carburetor which was used starting in 1967.  Volume 67 S2 L2, 9503.1, 9503.2

Used Transition cover for the 68 - 69 Cougar or Mustang tilt steering column. This cover bolts to the outer cover tube.

This kit is an easy way to covert your 289 / 302 / 351W engine from a C4 or C6 transmission to an Automatic Overdrive Transmission. Kit includes: Cross memberTrans Mount InsulatorSlip YokeKick Down CableFlex Plate AOD Shift Linkage This is just the kit, and does not include the full transmission!

Core C6 transmission for a 1969 Mercury Cougar or Ford Mustang. Tag number PGA-Y or PGA-AE. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar S code with 390IP or 390-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core C6 transmission for a 1969 Mercury Cougar or Ford Mustang, with Q or R code 428CJ engine. Tag number PGB-AF1. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar with 428CJ engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core FMX transmission for a 1969 Mercury Cougar or Ford Mustang. Tag number PHB-E. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar with H code 351-2V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core FMX transmission for a 1969 Mercury Cougar or Ford Mustang. Tag number PHB-H. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1969 Mercury Cougar with M code 351-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Core FMX transmission for a 1970 Mercury Cougar or Ford Mustang. Tag number PHB-P. Floor shift FMX Transmission. Core transmission only, No bell housing, dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1970 Mercury Cougar with M code 351C-4V engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Used C-4 transmission 90 degree brass fitting for the rear oil cooler line. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.Not all of the transmissions had a 90° fitting. Compare with your cooling lines.

Fits all applications for both automatic and manual transmissions, big block and small block. Will also work with your Tremac / T-5. Replaces Ford part # C4DZ-6068-A.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

An exact copy with a beautiful chrome mirror finish.

An exact copy with a beautiful chrome mirror finish. 1 inch deeper than stock.

An Exact copy. Natural gray paint for correct look and rust prevention. 1 inch deeper than stock.

Flawless chrome plating, available in stock depth only. Includes drain plug.

An Exact copy. Natural gray paint for correct look and rust prevention.

Flawless chrome plating, available in stock depth only. Includes drain plug.

Reproduction transmission selector tube seal for the 69 - 70 Cougar or Mustang steering columns.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

New manufactured transmission yoke for a T-5 5 speed transmission.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX  cars.  *Excludes 351C-4v and 351CJ engines.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

New manufactured Tremec T-5z World Class Transmission. Same transmission as installed in Fox Body Mustangs. This is the common transmission for conversions that does not involve extensive modifications to 1967-73 Mercury Cougar or Ford Mustang. Small block Ford V-8 engines only, 289 / 302 / 351W and 351C. Brand new transmission, no core required. 1 year warranty, with recommended synthetic ATF. Flush and fill after first 500 miles, 30,000 miles there after. Bare transmission as shown, no...

Slightly wider than the 1967 version. Customer feedback at mercurycougar.net: I did a drum to disc conversion on my '68 a few months ago. WCCC sold me 2 orig. cougar brake setups from spindle to caliper to brake lines with the P. valve , you know complete.. These freaking brakes looked like they were a year old, no sh**. I had my Friend Perry from "Perry's Pony Express" a Classic Mustang restorer here on Long Island help me install them & he told me they were the cleanest 1968 used brakes...

Reproduction emergency / parking brake pedal pad trim piece for the Mercury Cougar or Ford Mustang. This great little reproduction looks good and is one of the little detail pieces that can separate a nice car from a mint car.Replaces Ford part # C9ZZ-2A487-C.

Used emergency / parking brake pedal pad that features all stainless steel construction. This unit cleans up very well with fine steel wool, has reusable folding tabs, and is easy to install. A great piece to finish off your interior!Replaces Ford part # C9ZZ-2A487-C.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Reproduction trunk wheel house seam cover for the Ford Mustang. I have actually never seen an original pair of these on a car, but they do serve a purpose if you are in the habit of cramming your trunk full of items you do not want scratched. These attach to the protruding seam where the inner and outer wheelhouse bond together and measure about 14" in length. You will have to modify these to fit your Cougar. Only sold in black. Replaces Ford part # C5ZZ-6531466-A.

Used inner steering column tube for the tilt / tilt away for the Mercury Cougar or Ford Mustang. This unit fits within the outer steering column and is specific to 1969. Ford part # C9AZ-7212-F. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction oil pressure remote sending unit tube assembly. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge.The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell shaped oil...