1968 Ford Mustang

Stud for attaching heat shield to passenger side exhaust manifold. Fits all 1968 Mercury Cougar or Ford Mustang and other Ford too. Sold individually. Phosphate & Oil (gray-black)

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the longer of the two stud bolts. See item 41350 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 382803-S

Exhaust manifold bolt / stud for mounting the heat shield on the passenger side. This is the shorter of the two stud bolts. See item 31171 for the short heat shield bolt. For all Mercury Cougar or Ford Mustang, Torino, Cyclone, etc. with Q or R code 428 cobra Jet engines with factory cast iron exhaust manifolds. We also sell the complete bolt kit for the CJ exhaust manifolds. 

Reproduction 15x7 chrome styled steel wheel for your Cougar or Mustang. Technically correct for Mustang because of the holes being placed in the center of the arms instead of in the inserts like the Cougar, but will fit both vehicles. Gorgeous reproduction of the original 1968 Mustang styled steel wheel. Correct in every way except that the outer band is welded on instead of riveted to the center section. This wheel has a total width of 7", backspacing is 4" and the center hole is...

This is the 1968 Cougar visor bracket. Not an exact match for 1971 - 1973, but will work. The hole spacing and distance from the windshield is identical to that on the 71-73, the bracket is just 1/8" longer on the side that actually holds the visor tip. This unit is only available in black or neutral. We have most other unfaded colors in used. This item works for 68 Cougar Coupe, 68 Mustang Coupe / Convertible and 71-73 Cougar Convertibles. Replaces Ford Part # C8ZZ-6204132, C8ZZ-17690 OR...

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

For the purists out there we have a very limited amount of used moon crater visors that have no impressions, seam separation and minimal rust on the clips if any.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually.

Reproduction Moon Crater Sun Visor for the 1967 and 1968 Mercury Cougar / Ford Mustang. Visors are fully padded and covered with the correct textured moon skin to match the headliner. Sold as a Pair. Nugget Gold is not available in Moon Skin Crater, it is only available in a smooth vinyl.

This decal was sometimes placed on the dash face pad near the middle or right side, and sometimes on the sun visor.

Used strap or support bracket for the foam air conditioning vent tube going to the driver side A/C vent. The electrical assembly manual indicates that this strap bracket behind the dash on the driver side. Our findings from the wrecking yard show that 1967 is typically rubber coated, 1968 is bare steel. Please specify is you have a preference. The rubber coated ones will show some deterioration, plan on re-dipping or use as-is. Not exactly the same as the support for the passenger side.Ford...

Reproduction brake pedal hanger for manual brakes. Can be modified to work for power brakes.

This used brake pedal support bracket is the correct hanger for a 1967-68 Mercury Cougar or Ford Mustang with manual drum front brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means the clutch bushings will be in mint, unused condition. Ford part # C7ZZ-6501508-C. *NOTE* Manual brake supports are different. Manual brake supports have four threaded...

This used brake pedal support bracket or brake pedal hanger is for the Mercury Cougar or Ford Mustang equipped with power disc or drum brakes. We have carefully shown the mounting position of the pedal so you can drill your existing manual brake pedal hanger when converting from manual to power brakes. If you have a manual transmission car with worn out clutch bushings, this is a great replacement part for you as it will have been removed from an automatic transmission equipped car. This means...

Radio support bracket for 1967-68 Mercury Cougar and Ford Mustangs without consoles. Used on AM, AM/FM, and AM/8Track factory radios.Replaces parts #s C7ZA-18888-A & C8ZA-18888-A, as found in the electrical assembly manuals.

Reproduction sway bar clamp and rubber bushing set for 1" sway bars on 1967 - 1973 big block Cougars and Mustangs. 

Reproduction sway bar clamp and bushing set for 3/4" sway bars on 1967 - 1973 Cougars and Mustangs.  These polyurethane bushings reduce deflection at the bar mounts to quicken the action of stock or aftermarket sway bars, and come with matching mount brackets. Includes lubrication groove to prevent squeaking. Replaces Ford Part #: C5ZZ-5486-H

DOES NOT FIT BIG BLOCK Reproduction 1 1/8" sway bar for 1967 - 1970 Cougars and Mustangs. End link and bushing kit is included.

Reproduction big block 1" sway bar for 1967 - 1970 Cougars and Mustangs. Keep in mind that this sway bar does not come with mounting brackets or the end link kit.  

C7ZZ-5482-C This is a factory used sway bar for the Special Handling Package as found on with the 1967 and 1968 GT option. This bar was factory identified with a single 'Green' paint stripe. This factory used front sway bar, does not include any mounting brackets or end link kits.

Now in black with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

Now in grey with no zipper, our comfy WCCC hoodie features bold new walking cat graphics on front and back. Perfect for staying warm in the garage, or out and about with your Cougar! This sweatshirt is made with soft, mid weight fleece and generous fit for comfort. Features a jersey lined hood, heavy gauge drawcord with metal eyelets and 1x1 ribbing at cuffs and waistband. 8.5 oz fleece80% cotton 20% polyester blend100% cotton 20 singles face yarnSplit stitch double needle sewing on all...

This sporty quarter-zip sweatshirt features a Mercury man on the front left chest, "Mercury" script down the right arm, and a Team Cougar logo on the back. A cool tribute to the winning 1967 Trans Am team, and a great way to represent the brand while staying warm. 8.0 oz., pre-shrunk 50/50 cotton/polyester1x1 athletic rib with spandexBrass zipper and dark grey trimSelf fabric lined collarSatin labelDouble needle stitching at waistband and cuffsQuarter-turned ...

Plunger switch that mounts to the air distribution manifold behind the center A/C vent. A mechanical lever operates the switch when the air damper is in the proper location to distribute air through the center air conditioning vent of the dash. This switch controls the clutch on the A/C compressor. 1967-68 Mercury Cougar and 1966-67 B Body Ford, Fairlane, Ranchero, and C Body Mercury Comet and other variations Cyclone etc. Tested and working switch. On Cougar and Mustang it attaches to the...

Used air conditioning thermostat switch for any 1967-68 Mercury Cougar or Ford Mustang with integral or factory A/C. Attaches to the side of the fiberglass box under the dash, the wire probe gets inserted into the evaporator. Tested and working switch. These were originally manufactured by Ranco for Ford. Ford part numbers C7ZA-19618-C or C7ZZ-19618-A.

C7ZZ-15520-C Backup lamp switch that mounts to the factory 3 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-573.*Note - 3 speed switches are different than the 4 speed switches.

Reproduction backup lamp switch that mounts to the factory 4 speed shifter linkage. 67 - 68 Mercury Cougar and Ford Mustang applications. Autolite or Motorcraft switch number SW-561. Replaces Ford part number C7ZZ-15520-A.*Note - 4 speed switches are different than the 3 speed switches.

Reproduction brake light switch for Mercury Cougars and Ford Mustangs equipped with manual brakes. Ford originally called these stop lamp switches.Replaces Ford Part #: C9ZZ-13480-A.

Reproduction brake light switch for the Mercury Cougar and Ford Mustang equipped with power disc brakes. This is a high quality replacement part, but the appearance is not original. Ford originally called this unit the stop lamp switch. Replaces Ford Part #: C9VY-13480-A.

Reproduction brake light switch for the Mercury Cougar or Ford Mustang equipped with both power drum or disc brakes. This switch fits the 1967-68 for power drum or disc brake applications, and 1969-70, this switch fits power disc brake applications. Ford called this unit the stop lamp switch. Replaces Ford Part #: C7ZZ-13480-B or C9ZZ-13480-B.Fits: 1967 Mercury Cougar (power drum or disc)1968 Mercury Cougar (power drum or disc)1969 Mercury Cougar (power disc)1970 Mercury Cougar...

This switch mounts on the brake junction block to warn the driver of potential brake failure through a warning light on the dash. Replaces Ford Part #: C8AZ-2B264-A.

Used brake light warning switch for Mercury Cougar or Ford Mustang and Torino and is identified by the two pin connector. Screws into the brake distribution block. On a dual reservoir master cylinder this switch is supposed to light up if one side or the other loses pressure. For both disc and drum brake systems. Fits most if not all 1968-69 Ford and Mercury cars.Ford part # C8AZ-2B264-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Passenger side switch courtesy light switch, for use on 1968 - 1973Mercury Cougar and Ford Mustang. Replaces Ford Part #: C8OZ-13713-A.

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

C8ZZ-14018 Left side door ajar switch found on all 68 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-10B997-A switch assembly left hand. The engineering number cast...

C8WB-14018-B Right side door ajar switch found on all 68 Mercury Cougar XR7's and part of the Safety Convenience Package found optionally on Mercury Cougar or Ford Mustang. The safety convenience package or "convenience control" option included 4 warning lights either mounted on the dash (without air conditioning) or on the console. Switch assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 69, C7ZB-14018-A switch assembly right hand side. The engineering...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. OEM style door jamb switch to release tilt/tilt-away columns on a 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the steering...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang, and most 1965-69 Ford and Mercury full sized cars such as Galaxie, Monterey, Parklane, Montclair, etc.Fits 67 CougarFits 68 CougarFits 65 Mustang Fits 66 MustangFits 67 MustangFits 68 Mustang

NOS new old stock headlight dimmer switch. This is a Motorcraft service replacement switch.  Replaces Ford part number C0TZ-13A024-A

This quality reproduction is made from the original tooling and should give you the same reliability of the original that lasted 30-40 years. Replaces Ford part number C0TZ-13A024-A

Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. New Old Stock switch and wiring pigtail with plug. Ford part # C8ZZ-18578-B

Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Switch and wiring pigtail with plug.Replaces part # C8ZZ-18578-B.

Mounts to the rear of the factory installed heater control ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Ford part # C8ZZ-18578-B

New Old Stock NOS Fan switch for use with air conditioning on any 1968 Mercury Cougar or Ford Mustang. Mounts to the rear of the factory installed air conditioning ventilation control panel on Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing our 1968 selector button kit. Ford part # C8ZZ-19986-A. ...

This used A/C fan switch mounts to the rear of the factory installed air conditioning ventilation control panel on 1968 Mercury Cougar and Ford Mustang. Good working switch and wiring pigtail with plug. Save your knob or consider purchasing our 1968 selector button kit.Ford part # C8ZZ-19986-A.

Tested and inspected neutral safety switch for the C-4 and C-6 transmissions installed in 1967-69 Mercury Cougar and 1967-69 Ford Mustangs. Look for a transmission code of W or U on your door data plate. If your car has a code X, your original transmission was an FMX and uses a different neutral safety switch.Replaces Ford Part #: C7DP-7A247-A, C8ZP-7A247, C9ZZ-7A247-C, SW 887.Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969...

High quality alternative to the expensive OEM switch. If you have an early 67 the plug may be the dual type which is also listed on this site. This will work with your C-4 or C-6 automatic transmission. The only real difference is that this switch does not come with the FoMoCo logo or part number on it. Replaces Ford Part #: C9ZZ-7A247-B, SW 877