Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
There are two or three manufacturers on many of the products in this section but many are only available from one source. We ALWAYS look for the BEST supplier, NOT the best price. Very few of these products are as good as what Ford supplied. Many people unknowingly discard every piece of rubber on a car when they tear it down for restoration thinking that new is better than old. In most cases this is correct thinking given the age of the parts being removed but not in all cases. Carefully inspect each of your OEM rubber parts before you decide to replace them with new. Many of the items here were available from FORD through the nineties and may have already been replaced on your car. Whereas we would like nothing better than for every customer to purchase every item in this section, our foremost goal is preservation of these classic cats.
Please click onto the individual items to obtain price and other details. You can click the image up to three times for a larger view. Need help? Call 503-463-1130
Buy Details
Rubber bumper / stop that sits atop the vertical center grille support on the 71 - 72 Cougar. Most times, these are very brittle and crumble when you handle them, but every once in awhile we have a bad support piece and we're able to salvage the rubber bumper.
Rubber bumper used on 69-70 taillight housings to cushion the closing of the fuel door, sold individually, two required per car. Replaces Ford Part #: 16758.
Sold individually, four required per car. Replaces Ford part #: C7AZ-5426528.
Four per car, mounts to fender. Sold individually. Replaces Ford part #: C7WY-16758.
Sold individually, four per car, mounts to fenders. Replaces Ford part #: C6OZ-16758.
Four per car, mounts to fenders. Replaces Ford part #: C7WY-16758.
Four per car, mounts to fenders. Replaces Ford part #C6OZ-16758.
Reproduction license plate / fuel door cover rubber bumpers for the Mercury Cougar or Ford Mustang. These will also work for the 1969-70 Mercury Cougar or Ford Mustang cowl cover to hood rubber bumpers. Sold as a pair with the mounting screws. *NOTE* These are not an exact replacement, rather a part from another year and application that has been found to be an adequate substitution. If you really need an exact replacement we sometimes can provide a used bumper. ...
These Radiator Hood Support Bumpers reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.
These stainless steel radiator hood support bumper reproductions are sold as a pair. They fit the 67, 68, 69, 70, 71, 72, and 73 Mercury Cougar. Replaces Ford part #: C5ZZ-16763.
This is the correct, original cover for your 1971-73 Mercury Cougar and 1971-73 Ford Mustang antenna. The Ford MPC calls this part a cap, it is the stainless steel rectangular piece of trim that goes on top of your factory antenna base. These are angled, so watch the orientation when installing. These snap into place on the OEM factory installed antenna base. Used gasket also available.Replaces Ford part number C5AA-18A927-A.
Partially dipped clip for attaching the fuel line harness or trunk wiring harness, or fuel line at fuel tank. Found in various places on 1967-70 Mercury Cougar and Ford Mustang.
Partially dipped clip for attaching the seal on top of the radiator core supports. Often times with air conditioning the seals were installed. The factory sometimes used staples, sometimes clips. You would have to investigate your core support for staple holes. 5 clips are typical for attaching the seal. Spread them apart to where it looks equal. Applications: 1967 - 1969 Cougars and Mustangs equipped with the 390 engine, and 1970 Cougars and Mustangs with the 428CJ engine. ...
Replaces Ford Part # : D0OZ-7583
These reproduction pads are high quality replacements for worn or missing original pads. Replaces Ford part number C9ZZ-7A624-A.
15 Piece kit that includes quarter panel drain plugs.
The picture above shows these bumpers installed in the 100% correct reproduction console that we sell. These are sold individually, 2 required per car. Replaces Ford part # 379919.
Reproduction pair of rear bumper corner fillers for the 67 - 68 Cougar. The Mercury MPC refers to these as "anti squeak pads." Replaces Ford part numbers: Driver side - C7WY-16304-C Passenger Side - C7WY-16304-D
Covers the metal, foot operated headlight dimmer on the driver side floor pan. Replaces ford part #: C5ZZ-13533-A.
Clear plastic cowl seals for all 1967-68 Mercury Cougar and Ford Mustang. These are supposed to prevent rain or water from entering your cowl vents in front of the windshield. These were created to help prevent water from dripping on your floor from leaking cowls. These fit fairly well, but you need to check all of the corners when installing. We feel that they are a little under sized to properly seal those cowls easily. Our first attempt left one of the corners with a gap, thereby allowing...
Four required per car. Replaces Ford Part #: C2AZ-6223030.
This A/C evaporator drain hose is molded flex hose similar to the original, but it will need to be cut to the proper length. It is correct for 67 - 68 but can be made to work on 69 - 73. Replaces Ford part #: C7ZZ-19858-C or C8TZ-19858-A.
Clutch Lever Dust Boot for the 289, 302 and 351. Replaces Ford Part #: C6OZ-7513-C.
Reproduction clutch lever dust boot for the Mercury Cougar or Ford Mustang. This unit is used with the 429 in 1971 and in all Cougars and Mustangs in 1972 and 1973 equipped with manual transmissions and the 351 engine.Replaces Ford part #C5AZ-7513-A.
This reproduction is made from the original Ford tooling and is new to the market. Well worth the few extra dollars over the previous ones offered. Replaces Ford Part #: C6OZ-7513-A.
This Lower Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73. Replaces Ford part # C7OZ-3105-A.Just and FYI, in order to install this boot, the entire lower ball joint must be removed from the lower control arm. That means grinding or drilling out the rivets, or removing bolts is so equipped.
This Upper Ball Joint Dust Seal reproduction fits the 67, 68, 69, 70, 71, 72, and 73.Replaces Ford part #: C7OZ-3105-B.*Installation tip - The inside diameter of the grommet is just a hair too small to properly fit on the stud. Restoration expert and MCA Judge Marcus Anghel, suggests using a slightly larger round punch to open the hole slightly. If the boot isn't seated low enough, the boot will tear and fail in short order.
Reproduction rubber dust seal or boot for front suspension upper and lower tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. *Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #C6OA-3332-A or C6OZ-3332 ...
Reproduction rubber dust seal or boot with steel reinforcing ring for front suspension inner and outer tie rod ends. 1967-69 Mercury Cougar, Ford Mustang, and many other Ford cars. This is the concours version with Ford casting number C6OA-3332-A.*Note - This fits the early tie rod ends. If you have changed to later model disc brake spindles or the Granada conversion, we don't have an option for that.*Note - Excludes 1969 Boss 302 cars and some 1969 Shelby GT500 Mustangs.Replaces Ford part #...
Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...
Replaces Ford part # C5ZZ-9673. Fits 1967 289 and 68 -70 390 - 428 cars without Ram Air (C8ZZ-9673).
This 67 and 68 Firewall To Hood Seal Reproduction has attached rubber studs for mounting. Replaces Ford Part #: C7ZZ-16740.
Rubber plugs for sealing the holes in the firewall of any 1967-68 Mercury Cougar or Ford Mustang. These plug the firewall holes if you don't have air conditioning or if you have deleted your heater core. Fits 1" body panel holes for all years.Sold as a pair.Original Ford part 377678-S2
Sold in a set of three, includes attaching screws. Replaces part # 380478-S3
Reproduction firewall to hood seal or cowl seal for the Mercury Cougar or Ford Mustang. Comes with attaching clips. Replaces Ford part # D1ZZ-16740.Customer feedback from mercurycougar.net: Don and WCCC were always one of the service quality benchmarks for my business. Despite the many pressures faced by any small business owner, Don always treated me and my car as if we were his only customer. And, he NEVER let me down - parts always as advertised, and delivered timely.That impressed me then,...
Replaces Ford Part # : D1ZZ-3513-A. For use only with 3 and 4 speed manual transmission cars.
Sold individually. Replaces Ford Part #: C7ZZ-3513.
Seal the steering column flange to the firewall. Used on cars with automatic transmission. Replaces Ford part # D1ZZ-3513
Windshield Washer Pump Pedal Pad for 1967-1968 Mustang & Cougar. Keep your foot from sliding off the pedal with this Injection-molded rubber pad with vertical grooves just like original. This pad was used on models with a floor mounted washer pump pedal. (7664A) This is almost always missing off of the end of your foot operated washer pump. Replaces Ford part number C7ZZ-17664-A. We also have good used pumps in stock. Thanks for the plug Mark!: My first deal with Don was clear back in the...
Front Parking Light To Valance Pads are sold as a pair. Fits the 67 and 68 Cougar or 65 and 66 Mustang. Replaces Ford part #: C5ZZ-13217.
Reproduction fuel line to side apron grommet for the Mercury Cougar or Ford Mustang. 3 needed per car.Replaces Ford part # D1ZZ-9288.
For use with 1967 390 and all 1968-73 air cleaner lids except Ram Air which uses no gasket. Replaces Ford part #C8ZZ-9673.
Reproduction antenna base gasket.Replaces Ford part # C5ZZ-18A813-A
Replaces Ford part #D1AZ-6522428. Sold individually.
Made from fuel resistant cork like original. Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...
Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.
Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.
This gasket is found behind the trunk lock housing, which the lock itself sits in behind the trunk lock cover plate, and forms a seal between the trunk lock housing and the trunk itself. Made of soft rubber much like the original. Replaces Ford part #: C7WY-6543625.Check out our video below showing how to easily remove and reinstall your 67-68 trunk latch, lock, and cover plate, and some info on getting a new key made. ...