1970 Ford Mustang

Concours rear axle vent hose for any 1967-73 Mercury Cougar or 1965-73 Ford Mustang. Rubber hose that attaches to the metal nipple on the top of your rear axle housing. Fits 8 and 9 inch rear ends. Includes hardware as shown. Crimp clamp, screw clamp and bolt. Ribbed hose like original, and has yellow paint mark like from the factory. About 20 inches of hose is included, a little more than what was from the factory. Part number 4A001 in the chassis assembly manual.

Reproduction vinyl sleeve for the choke cable on the 1970 Cougar or Mustang equipped with a 390 or 428CJ. This sleeve protects the cable from rubbing on anything and prevent possible fraying.

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets. These were used on 1970 cars starting approximately 9/15/1969 on Non-Air cars, and some A/C cars. Some A/C cars came with one for the 68 A/C Voltage Regulator.Replaces Ford part number D0AF-10316-A (cover only)

Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.

New old stock NOS instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator until it is properly grounded, otherwise it...

New reproduction instrument panel voltage regulator or IVR for all 1969-73 Mercury Cougar and Ford Mustang. Additionally fits 1969-71 Torino/Cyclone without tachometer, 1969-70 Ford full size, and 1970 and newer Ford Maverick or Mercury Comet. Mounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Features Solid State electronic circuitry. Ford part number C9AZ-10804-A. Note: 12v constant input with a pulsed 5v output. DO NOT power up the voltage regulator...

Features the proper cover and original logos. I A S F stamped on cover. These were used on 1970 cars starting approximately 9/15/1969 on Non-Air cars, and some A/C cars. Some A/C cars came with the 68 A/C Voltage Regulator. Replaces Ford Part #: D0AF-10316-A. The voltage regulators listed in this section are poor quality. We suggest you buy a reliable, modern, solid state unit and just use the cover we sell as a stand alone product. We will not warranty the mechanical voltage regulators you...

Voltage regulator for the 1968, 1969, and 1970 manufactured before 9/15/1969 that is not equipped with factory AC. This regulator has "C8AF-10316-A" printed on to it, actual Ford Part number is C3SZ-10316-B or D4TZ-10316-A. This is Ford Regulator Number GR-341. These new voltage regulators are improved and more reliable than the units we've sold previously.

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets.Replaces Ford part number C8AF-10316-A (cover only)

Washer or spacer for heating and air conditioning box levers or shafts. Fits 3/16 inch studs or rods. In most cases you will also want to get a push on retainer to keep secure.

#373820-S Copper washer for attaching the 8 inch or 9 inch third members to the axle housings. Steel washers will leak, made from copper which is a soft metal and seals under the attaching nuts. Copper washers like the OEM Ford installed washers. Takes 10 washers total for both 8 and 9 inch rear ends. *Tip - It is a good idea to inspect or replace your old washers, many times they have tool marks from the housing or nuts that cause small troublesome leaks.

Almost identical to the original, tab is a bit longer. *NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

AMK seat belt washer B-13023. 0.46" ID x 1.25" OD zinc flat washer. Sized so that it rides on the shoulder of the seat belt bolts. It allows the retractor to rotate freely between this washer and the head of the seat belt bolt on 1969-73 cars. Two required per car, used only on the re-tractors.

This is the rubber spacer / washer that goes between the bolt head and the metal washer of your seat belt hardware. The purpose of the rubber washer is to dampen any vibrations caused by the movement of the seat belt.Sold individually# 354959-S

Often you will see minor irregularities in these washers. These would be considered "blems". Two required per car, used only on the re-tractors.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement.

These spacer / washers were used on the rear belts of 1968 - 1973 Cougars. 1968 used two per bolt for a total of eight, 69-71 used one per rear belt for a total of four and 72-73 used one per belt on the inner only as the outer belts had a re-tractor in the rear 72-73. They were red to guide the line workers on placement. Sized like the originals, but do not have the dimples all over. 0.53" ID x 0.88" OD.

OEM replacement water pump for the 351 Cleveland. Gasket included. Replaces Ford Part #: D0AZ-8501-E.

OEM replacement Water Pump for the 351 Windsor. Gasket included. Replaces Ford Part #: D0OZ-8501-A.

Light duty OEM Replacement cast iron water pump for any Ford FE 390 / 427 / or 428CJ. Gaskets included. No Core required Replaces Ford Part #: C8AZ-8501-A.

0D13  April 13, 1970 dated.  Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C9AE-8505-A. Found on many Ford 390 and 428CJ engines from 1969-70. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting...

Water pump gasket for all 289/302/351W/351C/429 engines. This gasket is used between the water pump and water pump plate.

Reproduction water bypass plate for all Ford 351C engines. This is an original style brass restrictor plate for 70-73 Cougar, Mustang, Torino etc.Must be used in conjunction with the correct 180 degree thermostat.For some helpful tips on upgrading your Cougar (or Mustang) cooling system, check out our video: ...

New water restrictor plate for the Mercury or Ford equipped with the 351 Cleveland engine. It has been an accepted fact for decades now that the 351C bypass system was not the greatest idea Ford ever came up with. The unique 351C thermostat "hat" never seals well, causing a certain portion of coolant to just circulate through the block and never make it to the radiator. Years ago, Pantera enthusiasts (all Panteras had cooling issues from the factory BTW) found that if they soldiered a penny...

Wave locking washers for the door hinges on the 67 - 70 Cougar or Mustang. These washers have teeth that will dig in and hold tight, making sure your door hinges never come loose.

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

This concours correct reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This Daniel Carpenter manufactured unit is made of slightly less dense material than the Midland unit, .75lb as compared to .85lb. If correctness is not an issue for you, you can get the Midland unit here. We have included a few comparison pictures so...

This offshore reproduction weatherstrip is for the perimeter of the doors on the Mercury Cougar or Ford Mustang. This set has the door to back of door glass seal bonded to the end of the strips and will need to be glued in place. This overseas reproduction sold by Daniel Carpenter is simply another option to the US made version, and has been known to fit better than the US made weatherstrips. If correctness is not an issue for you, you can get the Midland unit...

Reproduction door glass to roof weatherstripping for the Mercury Cougar and Ford mustang. These units are sold as a pair and are also known as the roof rail weatherstrip. Replaces Ford part # C9ZZ-6551222. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Reproduction driver side (left hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium piece made with the original Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Good fit and quality. This will fit your 70-73 coupe or convertible. Unlike the 1969 strip this vertical strip slides into the 1/4 window stainless steel moulding that attaches to the leading edge of the rear 1/4 windows. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Reproduction passenger side (right hand) vertical quarter window weatherstrip for the Mercury Cougar or Ford Mustang. This is a premium unit that made made with orginal Ford tooling. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

This kit is easier to install than you may think! Five piece kit, comes with installation instructions. Be aware, the seals at the top of the glass do not line up perfectly leaving a gap on the quarter glass top seal. We are working on a solution.  Replaces Ford part # C9ZZ-7653986. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! ...

Sold individually, phosphate & Oil (gray-black).

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems for installation of the new Legendary aluminum wheels. These really only fit the Magstar style wheels; we recommend the 3/4" lug nuts for all the other Legendary wheels for clearance reasons. Conical Head: 13/16" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome tapered 13/16" lug nuts and 4 chrome valve stems. Specifically for installation of the new Legendary GT7 and 1966 Shelby wheels. Thread Size: 1/2" Bolt Pattern Check out our video on Legendary Wheels below: ...

5-Lug Kit includes 20 chrome lug nuts and 4 chrome valve stems for installation of the new aluminum Legendary Series wheels. Tapered for correct fit. This 3/4" size is what we recommend you use with the Legendary wheels, since the clearances are too tight for 13/16" nuts. Conical Head: 3/4" Hex Thread Size: 1/2" Bolt Pattern Also available individually.Check out our video on Legendary Wheels below: ...

This hard to find cast aluminum spacer may be all you need to provide that little bit of extra clearance for calipers, control arms, frame rails, etc. At only 1/8" thick, it does not require longer wheel studs like many thicker spacers you find on the market.

New wheel stud replacement for all Mercury Cougars equipped with front drum brakes. Pretty much fits most other front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only, serrated 2" stud with correct 1/2 x 20 threads. These are slightly longer in length than the stock ones, this will allow the alloy wheels to fit the Classic Cougars.Replaces Ford part # C30Z-1107-A.*NOTE* You should use a press to remove and/or install the new studs.

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide.This ring will have one or two small scratches or dings that will be noticeable. Replaces Ford part number D0DZ-1210-A.Fits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972 Ford...

Used on 1970 - 1973 Kelsey Hayes, style steel wheels, 14 x 6". Master Parts Catalog description: 15-1/4" O.D., 11-3/16 I.D., 2-1/4" wide. No dings and only the slightest scratches.The part number is D0DZ-1210-A and the engineering number is D0DA-1210-B. Sold individuallyFits the following models with styled steel wheels: 1970 Ford Mustang1971 Ford Mustang1972 Ford Mustang1973 Ford Mustang 1970 Ford Torino1971 Ford Torino1972 Ford Torino1973 Ford Torino 1970 Ford Maverick1971 Ford Maverick1972...

This trim ring will fit any 14" 67 - 70 Cougar Styled Steel wheel even though the width originally varied from 1.75" in 67, to 2" in 68 - 70. This ring measures exactly 2" high and has the correct bevel like original. The hue is as bright as original and it is the polished version, not brushed like the 68 used. Good tight fit, best of the 4 different makes you will see advertised around the country. Unlike the originals, these do not self center very well. You can however adjust them into...

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have slight blemishes that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

1969 and 1970 Cougar five spoke styled steel wheel trim ring. Master Part Catalog description: 15-7/8" Outer diameter, 11-15/16" Inner Diameter and 2" deep. This beauty ring will have one or two very small scratches or dings that will not be very noticeable.  Note that the 1969 Eliminator was the exception and used the 1968 brushed finish trim ring. Ford part number C7ZZ-1210-A.

Reproduction aqua headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Reproduction black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...