1970 Ford Mustang

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518

Used sleeve for fixed steering wheel. Special molded rubber sleeve that holds the bearing in place.  Ford part # D1AZ-3518 or E2AZ-3518

Complete kit with shaft for one side. Includes grease seals and zerk fittings. Note! Often times the fine threads in the upper control arms will be worn to the point of being stripped. To keep this kit properly in place you may have to tack weld the threaded caps to the control arms in a couple of places.

Sold individually, two required per car. These are brand new, not rebuilds. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford Part #: C7DZ-3082-A. Fits 1967-70 Mercury Cougar and Ford Mustang. We have found that this economy version does not fit 1971-73. There just is not enough clearance for this unit to bolt into the shock tower. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Sold individually, two required per car. These are brand new, not rebuilds. Please click onto the listing of our NOS arms to see side by side comparison pictures. We do not have the 4 bolt upper ball joint version available at this time. Replaces Ford part # C7DZ-3082-A. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

New quality upper control arm shaft kit. Fits all 1967-73 Mercury Cougar and Ford Mustang, also Maverick/Comet 1970-77, Fairlane 1966-70, Torino/Cyclone 1968-71. Comes with all parts shown. This is a much better design than the original Ford design. The down fall is it does not look at all like the original Ford kit. Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654607-A and are marked L.H. for the passenger side.

This plastic cover was put in place to cover the void at the very top of the panel. They are side specific and the textured side is installed upwards, on the bottom side you will find the Ford engineering number C9ZB-7654606-A and are marked R.H. for the passenger side.

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Key stock for 1967-73 Ford V-8 engines 3/16" square straight keys. Ships in 4 inch lengths, cut to fit the different applications. Common sizes 289/302 1-13/32", 351 1-3/4", etc.

Used vacuum actuator for controlling the center A/C vent on certain 1969-70 Mercury Cougar or Ford Mustang. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. This is the unique valve with two separate vacuum ports. 2 ports for two different positions. Studs are on 1-1/4 inch centers. Common single port vacuum valve is on 2-1/4 inch centers. Ford part number C9ZZ-18A318-A. ...

Reproduction vacuum actuator for controlling dampers and levers on the different year A/C boxes. These came in several different anodized colors. This is the basic valve with a single vacuum port.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors, for 1967-68 the color was brown. This is the basic valve with a single vacuum port.

Used vacuum actuator for controlling dampers and levers on the different year A/C boxes. This is a bare vacuum valve, that does not have the screwed on extension which make the unique part numbers from the Ford MPC. Tested and holds vacuum. These came in several different anodized colors. Blue is the color found 1969 and 1970 and early 1971. Blue and Brown actuators are exactly the same. This is the basic valve with a single vacuum port. There are other versions with an extra vacuum port...

Used extension or rod for the vacuum actuator for controlling the fresh air door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the right hand end, of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting...

Used extension or rod for the vacuum actuator for controlling the air restrictor door on the 1969-73 Mercury Cougar or Ford Mustang factory integral A/C boxes. This gets screwed onto the tab on the vacuum actuator, which make the unique part numbers from the Ford MPC. About 6 inches long. For 1969-73 Cougar and Mustang, has a dog leg jog as shown. On the front of the A/C plenum. Vacuum actuator sold separately, see related items. Stamped with Ford casting number C9ZA-18...

Used ported vacuum switch with filter. Unique piece, unknown application, definitely found on a 1968. Current offering are dated 8-67, 6-68, 5-68, 7-69, 8-69. Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number C8AE-A casting.This casting number is...

Original distributor vacuum advance control valve, also called a ported vacuum switch (PVS) valve, that was installed on all Ford models including Mercury Cougar, Ford Mustang, and Torino starting in 1967. This is a used original pot metal and brass part. It has the FORD oval logo and part number D0AE-A casting.This casting number is correct for all 1970 1971 1972 and 1973 Fords and Mercury. It was used on all engine options including 302 351C 351W 429 and 429CJ models. Because of the heavy...

Over 100 total vacuum caps in 6 different sizes.

Reproduction vacuum fitting for Holley 4150 carburetors as found on 1967-70 Mercury Cougar and Ford Mustang. All brass fitting, goes into the passenger side of the carburetor for the vacuum advance. This should be ported vacuum.Ford part number 358165-S.

D0ZZ-9A474-A Vacuum fitting for the rear of the intake manifold on a 1970 Mercury Cougar or Ford Mustang with the M code 351 Cleveland 4 barrel engine. Has two vacuum nipples or ports. 1970 Mercury Cougar Ford Mustang Modulation System - Bleed Assembly - Used D0AZ-12A168-C Very small inline vacuum hose bleed valve assembly installed very close to the distributor modulator control box.

Concourse Correct Vacuum Hose Aluminum Tie, used to dress up the distributor vacuum hose. Replaces Part # 383313-SA

Concourse Correct Brass Vacuum Hose Tie, used to dress up the distributor vacuum hose. Replaces Ford Part # 383313-SB

Very nice reproduction of the ram air flapper vacuum motor. Application 1968-1/2 428CJ Cougar and Mustang, 1969-71 Mercury Cougar with ram air, and 1969 Ford Torino 428CJ ram air. Not for shaker ram air systems.NOTE: These are manufactured with an extra long shaft to allow you to trim for an exact fit.

Saves time and frustration! Shows schematic and diagrams that reveals the location and function of the many vacuum systems on the Cougar.

This unit mounts on the main air chamber, it opens and closes the air vent. Made of nylon with a steel and brass plunger just like original. This unit is easy to test and can be seen by removing the glove box. Often it is the internal spring that fails on these and if your Cougar or Mustang will not easily change between blowing through the defrost ducts and the floor duct, this unit may be the culprit. Switch assembly, servo control. Replaces Ford part # C6OZ-18C311-A. *NOTE* You will need to...

Used vacuum switching manifold and electrical micro switch assembly from a 1969 to early mid 1972 Mercury Cougar and Ford Mustang. This is the all metal version vacuum distribution block. 1972 owners, please check your A/C controller to verify if you have or need the plastic version of this switch. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts...

Used vacuum tree for any 1970 Mercury Cougar, Ford Mustang, or 1970-71 Ford Torino. This manifold assembly mounts to the firewall in the engine compartment, and is unique to the above applications, as it has 6 different vacuum outlets or sources. These connect to the brake booster, heater / air conditioning vacuum parts, and other accessory items that use vacuum. Replaces Ford part number D0OZ-9C490-A or D0OA-9C490-A.

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 1/2/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 10/12/1967. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 2/21/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 3/19/1968. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Reproduction Carter 4491S smog canister valve with any supplied stamped date. Special order item, allow several weeks for delivery, and it will ship separately. Nice and detailed with correct stamping on the cover with your supplied date. Fits 289 / 302 / 390-4V / 427-4V/ 428CJ in 1968. Fits 428 Cobra Jet and 428 Super Cobra Jet for 1969-70. All 1968 Ford cars and light duty pickups received thermactor smog if they had a manual transmission and / or Holley 4V carburetor. Thermactor smog pumps...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 4/23/1968. This valve has the date stamped so that it is visible when looking at the...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 8/16/1967. Could also have a casting number of C8OE-9B289-B, the covers on the valves do...

Wide range of applications, which also include: 289-2V (C code engine), 302-2V (F code engine), 302-4V (J code engine) - Only 1968, and only with manual transmissions either 3 speed or 4 speed. 1968 390-4V, with any transmission. 1968 427-4V GT-E, and 1968 - 1970 428 Cobra Jet and Super Cobra Jet. Typical core valve, will not function. Basically selling a non functional smog part with a desirable date of 9/5/1967. This valve has the date stamped so that it is visible when looking at the...

C8TE-B-SR Correct service replacement 4490-S Carter anti backfire valve, but without the outer cover having the concours correct stampings. These units are used, not tested and one should assume they are non-functional.

Used shutoff valve for the headlight vacuum system of all 1969-70 Mercury Cougars. Also found on 1969-70 Ford and Mercury full sized cars with hidden headlights. Additionally these were also used on 1969-70 midsized Ford and Mercury such as Torino, Cyclone, also with hide away headlamps. This is a black plastic shutoff switch or connector, 1969 cars used a white valve that crumbled from the under hood heat. Note that the indicator tabs perpendicular to the lines means 'open'. Turning the valve...

Molded "S" shaped vacuum hose. Feed hose from the smog pump to the Carter anti-backfire distribution valve.

Core C-6 Transmission valve body for any 1970-71 Mercury Cougar or 1970-71 Ford Mustang with code "U" transmission code on the door tag. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as well. This is the special valve body for 1970 428CJ and 1971 429CJ engines. Ford...

Core FMX Transmission valve body for any 1970-71 Mercury Cougar or 1970-71 Ford Mustang with code "X" transmission code on the door tag. This is only for 1970 or 1971 transmissions with P-R-N-D-2-1 shift pattern. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket, we offer one as...

For 351 Cleveland or Windsor when equipped with the "Flame Arrestor" PCV Valve. Also fits multiple applications with 1" hole in steel valve covers in which the PCV valve presses into. Inside diameter is 23/32". Replaces Ford Part #: C8SZ-6892, C8SZ-6A892-A or 381898S.

Reproduction Ford blue painted valve covers for 289 - 302- 351W engines. These have 6 bolts to attach the valve covers. Excludes 351 Cleveland engines, they have 8 bolts for attaching.

SBVALVCOVER Ford engine blue painted valve cover with "Powered by Ford" embossed in the metal. Correct on 1968-1971 Mercury Cougar and 1968-73 Ford Mustang with 289/302/351W engines. Ford master parts catalog shows a right and left version of this cover those Service Replacement numbers are D2OZ-6582-C & D2OZ-6582-D. *Note - This cover will not work on a 351 Cleveland engine.

Reproduction pair of aluminum 428CJ valve covers. Correct on 1969-1970 Mercury Cougar and Ford Mustang with 428CJ engines. This is the plain finned aluminum valve cover. Sometimes called 1969 Shelby valve covers. Ford master part number C9ZZ-6582-B. Casting number can also be C9ZE-6583-B. *Note - Some 1969-70 428 Super Cobra Jet engines came with a different style of  "Snake" finned aluminum valve covers.

These "Cal Custom" style Valve Covers look great and really compliment the Finned Oil Pan and Air Cleaner. These covers offer a true "old school" look. * Requires one of each of the following (sold separately): PVC grommet, oil cap grommet, and push on style oil cap.

Finned aluminum Ford cast valve covers for any 1970-71 Ford or Mercury with 429CJ engine. Almost correct on 1971 Mercury Cougar and Ford Mustang with N or C code 429CJ engines. D0OE-6583-A is the part number cast on both. These both have the same opening for the oil filler cap on both sides. Technically, for 1971, the passenger side cover would have a round hole for the PCV grommet and have a D1OE-6583-CA casting number.