Body

Reproduction "A" pillar repair panels for your 69 - 70 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.

Hex head screw for attaching floor drain hole covers. Several different screws were used over the years and at different plants. All seem to be a #8 sheet metal screw of varying lengths. This is a #8 hex washer head tapping screw with 5/8" length. Two screws per drain cover, 2 or 4? per car, not sure. We also have the drain covers. 

Reproduction inner "A" pillar panel and fresh air vent vent panel set for the driver side (left hand) of the Mercury Cougar or Ford Mustang. This item features weld through primer and is ready to install. Unfortunately both Cougars and Mustangs alike are prone to rust in these areas, so finding a nice original piece can be difficult. We're delighted to have this high quality panel set to offer you the perfect pieces to replace those rusty units you have now!

Reproduction inner "A" pillar and fresh air vent panel set for the passenger side (right hand) of the Mercury Cougar or Ford Mustang. This item features weld through primer and is ready to install. Unfortunately both Cougars and Mustangs alike are prone to rust in these areas, so finding a nice original piece can be difficult. We're delighted to have this high quality panel set to offer you the perfect pieces to replace those rusty units you have now!

Ford called this small door latch part an adjuster. It threads onto the bottom of the door latch rod inside the door. Common to most Ford products 1965-1970. Ford part number C5AZ-62218106-A.

This plate is what is located on the backside of your door jam where your striker threads in one. Two threaded holes for attaching the striker plates on any 1967-70 Mercury Cougar or Ford Mustang. Right and left are the same. 

Reproduction Concours correct door lock rod anti rattle sleeve. This will come in a 33" length, and is cut-to-fit.

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

Reproduction pair of front apron assemblies without shock towers, perfect for someone doing a resto-mod or IFS conversion.  When installed this removes the shock towers and adds an additional 14 inches of width to the engine bay.  These full front apron assemblies are manufactured to have all the correct cutouts so you can run the wiring harness and the brake lines in the factory location. Sold as a pair.

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do.  No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although many would disagree, these are in my opinion average quality. "BUT" they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. We also have used in most colors available. Thank You Don and WCCC, Copy Cat's almost done! Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product. Without their patience and understanding along with a...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. The white color on these has an almost grey tint, these are a good neutral color to paint to whatever color you need. No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost...

Although some would disagree, these are in our opinion average at best quality. However, they are the best reproductions currently available. The inner portion where your fingers go have too sharp of edges and they do not hold up nearly as well as the originals do. The white color on these has an almost grey tint, these are a good neutral color to paint to whatever color you need. No return on these as we insure you up front you will not be impressed. Thank You Don and WCCC, Copy Cat's almost...

Good used group 24 tray for 1968-70 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray, for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting).

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

57084-S Attaching bolt with 7/16" hex head and captured washer. Among other things, it is used to attach the door run, window stops (all 3), both window stabilizers, and the window regulator. Same bolts for manual and power window regulators. Bolt sold individually, there are a good handful in each door. This bolt is used for bolting in the bolt-in glass on 1970, lower "L" bracket for rear quarter windows on 1971-73 Cougar and Mustangs.

Not a concours correct head pattern, but it looks good. Bright cadmium finish. 5/16-18 x 7/8 long.

Ford part # for the nut is 33772-S4, for the bolt 370301-S8, and the flat washer 358994-S.Slight changes in the hardware between the start of 1969 and the end of 1970. We see a slight difference in the height of the nut. Hard to tell unless side by side.

Reproduction bolts for the deck/trunk lid latch for the Mercury Cougar or Ford Mustang. This is a set of five bolts and will fit both the standard and XR7. Total of 5 bolts used 1969-73, 1967-68 Cougars will only use 2. We think that Mustangs use 5 on all years 1967-73. AMK F-227 Check out this video

Reproduction bolts and U nuts for mounting the front valances on either a Mercury Cougar or Ford Mustang.

Used to cushion and protect top vinyl from excessive wear from side rails. Unfortunately none of the reproductions that we have found resemble the OEM pads. OEM pads looked canvas on the under side that goes against the convertible top rails, and what looked like the soft side of a velcro strip on the upper side that makes contact with the convertible top itself. These are still highly recommended as they keep the convertible top rails from rubbing thorough the convertible top. "I found WCCC...

Sold as pair on exchange or outright. Only cores with minimal corrosion can be considered for exchange. Ford part number C7AZ-6204144-A, casting number as seen on the backside reads C8AB-6204122-B.  Does not include smaller rod for the sun visor tips.  Sold as a pair.

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

These brackets weld in the trunk to reinforce the rear structure for mounting the rear bumper. Fits all 1969-70 Mercury Cougar and Ford Mustang. Sold as a pair and are not side specific. 

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969 or early 1970 Mercury Cougar and Ford Mustang with glue-in door glass. This bumper will not work if your door glass is the 1970 bolt-in glass. We also sell the version for the 67-68 and late 1970 bolt in glass.Ford part # C9ZZ-6521762-A. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for...

This is the rubber that goes into the bracket of the bottom of the center of the door, for 1969-1970 Mercury Cougar and Ford Mustang glued-in door glass.  Note that this bumper is substantially shorter than the 70  bolt-in door glass version.   See D0ZZ-6521762-A for the 1970 bolt-in door glass version.  If you are swapping out a door on a 69 or a 70 don't forget that the door glass is different between the years and, if you have to swap out the glass, you will...

Sold individually, four required per car. Replaces Ford part #: C7AZ-5426528.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per car for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

Two or three of these clips were needed per door to mount the padded armrest. Three were used per armrest for a total of six, on 1969-70 Cougar and Mustangs. Two used in 1971-73 on standard Cougars. Sold individually.Replaces Ford part # C6AZ-6224146-B.

These are the plastic brackets that screw to you roof and then slide the vinyl colored piece over. Sold individually, four are required per car. Replaces Ford part # C8AZ-6229232.

Sold individually, black only. We have an array of colors in good used condition used. We also have the hard plastic bracket that this slips over. Four are required per car. Replaces Ford Part #: C8AZ-6229024-A.

Used driver side coil spring cover, taken from a parts car. Ford part # C7ZZ-3383-A.

Complete floor pan for the 1969-70* Ford Mustang or 1969-70* Mercury Cougar. This item ships direct from the manufacturer for most orders. This item must ship via truck freight. Shipping to business addresses tends to be less than residential addresses, sometimes substantially.This item ships direct from the manufacturer for most orders and must be shipped via truck freight, and CANNOT ship via UPS. Shipping to business addresses tends to be less than residential addresses, sometimes...

Replaces Ford part #C1SZ-13783. Replaces burnt, cracked or missing original lenses located above the rear package tray.  Two required per car, sold individually.

This is the chromed correct die cast construction for your 1969 Cougar, 1970-73 used plastic but these will fit fine and look better than the plastic units. Great Quality. Sold individually, two required per car. Part of the XR7 package. Available on other hardtop models, part of the Courtesy Light group option. Option included, engine compartment light, trunk light, map light and these rear quarter panel lights for the back seat. Replaces Ford Part #: C4SZ-13776-B.*Trivia Dearborn built...

This plastic socket is very brittle and almost always breaks when installing a new door jamb switches. Does not fit cars with Warning Group with door ajar option. Simply install by carefully breaking the old brittle plastic socket apart with pliers to free up the wire leads and plug wire leads into the new socket.

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!

These were never offered originally but are a popular accessory and more cost efficient than buying a replacement for that unsightly old wheel and tire you took from a Granada in the bone yard!