Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 241-288 of 369
$0.85 Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 32158 -

8-32 x 1 inch long screws for attaching automatic shift bezels on 1969-73 Mercury Cougar or Ford Mustang with added Mass Backed Carpeting. Shiny zinc screws as shown, set of 4. Replaces Ford Part #: 381571-S

$0 Price: $11.85

Buy Details

Availability: In-Stock Item
Item #: 25866 -

When it's time to replace your old decaying foam seal, go with our reproduction weatherstrip retainer foam roll with peel off adhesive. Goes between the roof and door / window channel.  These are not technically manufactured to fit the Cougar / Mustang, however these are very close to the originals and come from the manufacturer in a roll that is 4' X 1" X 1/8".  One roll is more than enough to do one side, but you will need 2 rolls to do both sides. ...

$0 Price: $2.65

Buy Details

Availability: In-Stock Item
Item #: 26814 -

These vinyl coated clips hold the weatherstrip and guide the window when rolling up. Used clips usually are rusted and the vinyl portion is peeling. Sold individually and four are required per car. Replaces Ford part #: C9ZZ-6522204. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

$0 Price: $8.65

Buy Details

Availability: In-Stock Item
Item #: 26586 -

Reproduction door glass seals for the front of the door to the window glass for the Mercury Cougar or Ford Mustang. Replaces Ford part # C9ZZ-6520264. Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information! 1969 Glue-In Glass: The Comprehensive Repair Guide Video

$0 Price: $2.75

Buy Details

Availability: In-Stock Item
Item #: 10907 -

Premium reproduction rubber seal with the proper thickness of the 1967-68 seal as found on Mercury Cougar and Ford Mustang except these are not molded to the extension contours. Starting in 1969 this channel seal was manufactured slightly smaller which tightened up the gap on the fender and quarter extension seals. This seal maintains the slightly larger gaps. Sold as a pair, two pairs needed per car.  Each package has 2 strips of 25 1/2" lengths. *NOTE* Do not over tighten the...

$0 Price: $9.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 32041 -

Used seat belt anchor plate that has been cut out from a car in our salvage yard. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford cars starting in...

$0 Price: $178.07

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 19390 -

This tower is technically incorrect for a 1969-70 Mercury Cougar as it has no reinforcement plate. Cougar owners would definitely want to buy a good used tower instead of this reproduction. Keep in mind all Cougars came with reinforced towers in 1969-70 just as all 1969-70 Cougars came with the 9" rear-end and 351 or larger engine.Here's a little film to help you fortify your flexxy feline! ...

$0 Price: $164.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19563 -

1970 features a reinforcement plate that is a combination of a 1968 and 1969 plate. This is an excellent upgrade for any 67-70 Cougar or Mustang without reinforced shock towers. This is a 100% clean, uncut tower worthy of any show-car. No specific part number for this structural front suspension section. For 1970, the plate size was shortened, for easier access for spark plug changes. Generic Ford part # D0ZZ-16055-B, included apron and side member. ...

$0 Price: $178.07

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 19433 -

We highly suggest you look at our mint condition used towers for about the same price. This tower is technically incorrect for a 1969-70 Mercury Cougar as it has no reinforcement plate. Cougar owners would definitely want to buy a good used tower instead of this reproduction. Keep in mind all Cougars came with reinforced towers in 1969-70 just as all 1969-70 Cougars came with the 9" rear-end. All Cougars also came with 351 or larger engines for those years as well, except for the 302...

$0 Price: $164.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19581 -

1970 features a reinforcement plate that is a combination of a 1968 and 1969 plate. This is an excellent upgrade for any 67-70 Cougar or Mustang without reinforced shock towers. This is a 100% clean, uncut tower worthy of any show-car. No specific part number for this structural front suspension section. For 1970, the plate size was shortened, for easier access for spark plug changes. Generic Ford part # D0ZZ-16054-A, included apron and side member. ...

$0 Price: $603.16

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 23644 -

Reproduction driver side (left hand) shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

$0 Price: $583.09

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 23645 -

Reproduction passenger side (right hand) shock tower and apron assembly for Mercury Cougar or Ford Mustang.Here's a little film to help you fortify your flexxy feline!

$0 Price: $31.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24823 -

Solid, undamaged, used driver side (left hand) shock tower brace for Mercury Cougar and Ford Mustangs. Consider our brace kits for the best bang for your buck! Ford part # C9ZZ-16A053-A. *NOTE* Excludes 1969-70 Boss 429.Here's our little film to help you fortify your flexxy feline!

$0 Price: $31.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24822 -

Solid, used, and undamaged passenger side (right hand) shock tower brace for Mercury Cougar and Ford Mustang. Consider our brace kits for the best bang for your hard earned buck! Ford part # C9ZZ-16A052-A. *NOTE* Excludes 1969-70 Boss 429.

$0 Price: $21.69

Buy Details

Availability: In-Stock Item
Item #: 41090 -

Reproduction shock tower brace nuts and bolts for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

$0 Price: $61.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19331 -

Used, solid, and undamaged shock tower braces for all 1969-70 Mercury Cougar and most Ford Mustangs. Includes 4 used 7/16"-14 x 1-1/4 inch cowl attaching bolts. Ford part #s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand).  *NOTE* Excludes 1969-70 Boss 429. **Installation Tip** These brackets attach 'under' the cowl lip. Here's our little film to help you fortify your flexxy feline! ...

$0 Price: $86.85

Buy Details

Availability: In-Stock Item
Item #: 41638 -

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

$0 Price: $89.87

Buy Details

Availability: Out of Stock
Item #: 20148 -

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...

$0 Price: $86.85

Buy Details

Availability: In-Stock Item
Item #: 41635 -

These are exact replacements for 1964-68 Ford Mustang, but looks similar to the 1967-68 Mercury Cougar. This floor pan will also fit the 1969-73 Ford Mustang, but 1969-70 cars have different ribbing configurations. To use this pan in 1971-73 cars will require modification. This heavy gauged stamped steel floor pan starts behind the seat platform *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either bend it up or remove it and...

$0 Price: $23.85

Buy Details

Availability: In-Stock Item
Item #: 26776 -

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

$0 Price: $35.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24774 -

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

$0 Price: $3.87

Buy Details

Availability: In-Stock Item
Item #: 26213 -

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out this video Still have riv-nut questions? Here are riv-nut answers! ...

$0 Price: $1.92

Buy Details

Availability: In-Stock Item
Item #: 42027 -

If your are missing your factory Riv-Nuts, or you are installing a passenger side mirror, these are a very easy to use alternative to the metal riv-nuts we offer. Another good application for these is when your existing mirror mounting holes are "hogged out" these slightly over sized inserts are just the ticket. Keep in mind our kit is not only less money than others you may find but the screws are stainless steel. Hole size for these rubber inserts is 3/8". Keep in mind the upper lip stands a...

$0 Price: $65.55

Buy Details

Availability: In-Stock Item
Item #: 25937 -

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

$0 Price: $34.09

Buy Details

Availability: In-Stock Item
Item #: 33055 -

Pair of reproduction sway bar mounting spacer plates, to be used with the 15/16 inch sway bar found on 427 4V / 428CJ / BOSS 302 cars.Mounts between the bracket and the frame mount.

$0 Price: $17.87

Buy Details

Availability: Discontinued, Limited Stock on Hand
Item #: 15318 -

This spring does NOT have correct spring finish or tension, but will work fine if you want to save a few $$$. Above is a comparison to this reproduction which is carried by other retailers, compared to our spring which is very close to the correct finish, length, and tension. Replaces Ford Part # : C8ZZ-17119-A ...

$0 Price: $990.77

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30650 -

Original space saver tire from a 1968-70 Mercury Cougar or Ford Mustang with the elusive 7.35-14 size. These were optional in 1968-70. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire.Just the tire, perfect for someone who has a dated wheel.*NOTE* Does not include inflator bottle and valve caps are usually missing. ...

$0 Price: $299.00

Buy Details

Availability: Out of Stock
Item #: 33358 -

Original space saver tire marked B.F. Goodrich F78-14. Display only, it can not be inflated. Rear side wall has damage. From a 1970-71 Mercury or Ford. Bolt pattern is 5 on 4-1/2. Not sure if it has ever been inflated, it is collapsed as shown.  Just looking for a space saver spare? Has the good tread design, single fill valve stem, but with damaged sidewall. This is it, it looks the part to those that casually look in the trunk of the car at a car show. Tread is a...

$0 Price: $995.04

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22230 -

Original space saver tire marked F78-14 B.F. Goodrich, from a 1970's Mercury or Ford. These were optional in 1968-73. It has the smaller hub size and single valve stem. Never inflated condition. One RARE unit! Just looking for a space saver spare? We have much lower priced space savers with different sized / marked tires, and some with dual valve stems from the 1970's. Please inquire. *NOTE* Does not include inflator bottle and valve caps are usually missing. ...

$0 Price: $16.75

Buy Details

Availability: In-Stock Item
Item #: 20551 -

10 5/8" Spare Tire Mounting Bolt. Not 100% correct, but close replacement for the 1969 - 1973 with the 10 3/4" spare tire mounting bolt. Diameter 7/16" Replaces Ford Part #: C8ZZ-1448-A, D0ZZ-1448-A & D1ZZ-1448-A.

$0 Price: $17.05

Buy Details

Availability: In-Stock Item
Item #: 41710 -

Very close to correct spring finish (dark color) and tension. Above is a comparison to the other reproduction, which does not have the correct finish, is not the correct length, and does not have the correct tension. Replaces Ford Part # : C8ZZ-17119-A *Note* Must be used with the correct mounting bracket. See below. ...

$0 Price: $81.85

Buy Details

Availability: In-Stock Item
Item #: 41626 -

Reproduction driver side (left hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03487-A.

$0 Price: $81.85

Buy Details

Availability: In-Stock Item
Item #: 41528 -

Reproduction passenger side (right hand) strut rod brace / support for Mercury Cougar and Ford Mustang.Replaces Ford # C8ZZ-03486-A.

$0 Price: $16.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 10750 -

Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops.  The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.

$0 Price: $24.89

Buy Details

Availability: Out of Stock
Item #: 10749 -

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

MSRP:$22.00
$22.00 Price: $12.75

Buy Details

Availability: In-Stock Item
Item #: 13783 -

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.

$0 Price: $100.07

Buy Details

Availability: In-Stock Item
Item #: 69_Vinyl_Sun_Visors -

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.

$0 Price: $4.55

Buy Details

Availability: In-Stock Item
Item #: 30515 -

Pair of reproduction cowl vent panel support pads. These pads help prevent the upper cowl cover from flexing. 

$32.00 Price: $38.57

Buy Details

Availability: In-Stock Item
Item #: 14194 -

OEM Motorcraft 2 prong door jamb switch 3/4 inch door jamb mounting holes. Various applications, some for passenger side, some both sides. Replaces Ford Part #: C8OZ-13713-A.

MSRP:$36.00
$36.00 Price: $29.57

Buy Details

Availability: In-Stock Item
Item #: 14200 -

Courtesy light door jamb switch with automatic seat back release option. Three pin switch not for use without seat back release. Additionally, this three prong switch was used on most 1970-76 Full and mid sized Ford, Mercury, and Lincoln. Some with or without the seat back release option. Replaces Ford Part #: D1AZ-13713-E and D0OZ-13713-A.

$0 Price: $6.36

Buy Details

Availability: In-Stock Item
Item #: 14198 -

This switch looks very close to original. On close inspection you will notice that there is no Autolite logo and the plastic is not as milky colored as the originals. Sold Individually. Replaces Ford Part #: C8AZ-13713-C.

$0 Price: $35.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0311 -

C9WY-14018-B Left side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

$0 Price: $30.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0312 -

C9WY-14018-A Right side door ajar switch found on all 1969-70 Mercury Cougar XR7's and part of the Visual Check Panel Package found optionally on Standard Cougars. The visual check panel or "convenience panel" option included the 'door ajar' light.Fits 69 Cougar and XR7Fits 70 Cougar and XR7 Fits 69 MustangFits 70 MustangFits 70 Lincoln ContinentalFits 71 Lincoln ContinentalFits 72 Lincoln Continental ...

$17.00 Price: $25.05

Buy Details

Availability: In-Stock Item
Item #: 14195 -

68 - 70 Courtesy Light Switches! These replacement switches are an exact reproduction of the original Ford part. This is the 2 pin type. Includes original Autolite Logo. Sold only as a pair. *NOTE* The 1967 uses a smaller pin assembly and this switch will not work without modification. Replaces Ford Part #: C8AZ-13713-C.

$0 Price: $3.65

Buy Details

Availability: In-Stock Item
Item #: 97979 -

This listing is for a TEMPLATE which would be used to cut your own shock tower weld in plates. Our supplier made a batch of weld in plates to the wrong thickness, so we're selling this template for anyone who has the ability to fabricate their own. As a stand alone item, this template will not work for what it's indented for because it's too thin. It's made from 18 gauge steel (the actual plates are supposed to be 11 gauge) so they're worth nothing more than being a pattern for the...

MSRP:$3.99
$3.99 Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 26641 -

These are usually cracked, shrunk or missing. Your visors will constantly fall out of the center holder if these are missing or shrunken. Sold as a pair. Replaces Ford Part #: D1DZ-6204115-A.

$0 Price: $29.57

Buy Details

Availability: In-Stock Item
Item #: 12210 -

This is an upgraded version from what you see in our video but the idea is the same. This tool has a square hole so you can use your 3/8" drive ratchet or breaker bar to get the correct angle and have even better control of your leverage when placing the torsion bar into the slot. Used to remove the hinge springs (torsion rods) off the 1967 - 1973 Cougar or Mustang. No more trying to remove with the wrong tools . These can be tricky to remove without this tool.  Will not work on 1964 -...