1970 Ford Mustang

This dealer installed kit was designed to fit many FoMoCo products. These were most commonly mounted on the driver side rear panel. They were taller than the standard antenna so mounting them on the driver side would protect them from low lying branches and other obstructions that more often come in contact with the passenger side of the car. This is one RARE unit for sure! ...

Reproduction "A" pillar repair panels for your 69 - 70 Cougar or Mustang. Included in this kit are the two pillar patches and four backing plates for the door hinges.

Non working core suitable for rebuild, not full of water and never been opened. These are located in the quarter panel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can...

Replacement radiator cap for the 1967 - 1973 Mercury Cougar or 1967 - 1973 Ford Mustang. This radiator cap releases pressure when the pressure exceeds 13 pound of pressure.

Reproduction 161 Exterior Side Marker Light Bulb for the 1969 and 1970 Mercury Cougar

This big book measures 18" x 13" x 3" and weighs 8 pounds. It's a must have if you are serious about electrical or vacuum work on the Cougar, Thunderbird, Mark III, Montego, Fairlane, Maverick, Cyclone, Bronco, F100, Torino, Mustang or other Ford products products from 1970. Condition is used and will have a few pages that have torn away from the rings. Form 7795P-70 Course 13003 and 1703

Comparative Guide of the 1970 Ford Performance Vehicles and the "Competition", which included the Cougar.

NOS Ford service training manual on diagnosis of charging system problems. This booklet is a guide to diagnosis of the alternator, regulator, battery and wiring issues. It contains diagnostic procedures and self instructional tests and was meant to be used as a reference guide for the "charging system videotape (video tape not included).  16 pages long with tests and answers.Issued Dec. 1974, # 365-240

Reproduction 2 speed windshield wiper switch for the Mercury Cougar or Ford Mustang. These "off shore" units are what other vendors offer, but they pretty poor quality and spotty at best. We highly recommend that you buy our good used units which you can get right here.

New Old Stock NOS windshield wiper switch for any 1970 Cougar or Mustang. Marked DOZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than the 1969 version.

Good used windshield wiper switch for any 1970 Cougar or Mustang. Marked DOZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than the 1969 version.

3/8 washer for installation of idler, adjusting pulleys, and brackets, on some 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, 1-2 are typically used per car. 

3/8-16x7/8 Bolt for installation of idler, adjusting pulleys, and brackets, on most 1968-73 Mercury Cougar and Ford anything, including Mustang. Sold individually, up to 8-9 are typically used per car. 9/16" hex, washer head bolt.

Swivel that mounts to the lower clutch rod or clutch adjusting rod. Original Ford part number D0ZZ-7A528-A.

Decal Text: Autolite EV-50 D0AZ-6A666-A Replaces Ford Part #: D0AZ-6A666-A.

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Cork Oil Pan Gasket for the 351 Cleveland Cork Oil Pan Gasket in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.

Cork valve cover gaskets for any 351C or 351 Cleveland Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Rubber valve cover gaskets for any 351C Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.

Chromed dipstick tube and dipstick for the 351 Cleveland. Average quality part, made in China. Replaces Ford part # D0ZZ-6750-K.

NOTICE: The supplier is no longer making the previous version of the upper hose, and the new hoses will have more of a textured outer wall.  Some Vendors show C8ZE for the upper hose, but C8WE is the correct stamping. These are the best CONCOURS radiator hoses on the market. All made in the U.S.A. by Gates or Goodyear both suppliers to Ford Motor Co, also approved by Mustang Club of America. All feature special white ink markings that have been designed to adhere to the hose under normal...

New One-Piece, Rubber Coated Fiber Oil Pan Gasket for the 390, 427 or 428 FE Big Block engine in the 1968, 1969 or 1970 Mercury Cougar and Ford Mustang. 3/32" thick.

OEM Style Oil Pan Gasket.

1969-1973 4 amp Buss style glass tube fuses sold individually and used for the instrument panel, clock, radio, heater control, and ashtray lights.

Backup light switch retainer for Hurst shifters as installed on 1970-73 Mercury Cougar, Ford Mustang, and most vintage Ford cars with factory installed Hurst shifters.

Spark Plug Wire Separator Brackets for the 1969 - 1970 Mustang Cougar or Torino with 428CJ Finned Aluminum Valve Covers, 1969 - 1970 Mustang Boss 302 with Finned Aluminum Valve Covers or Boss 351 models. These are an MCA approved unit made here in the USA. These replace Ford part number C9ZZ-6583-A and include both brackets and the 4 screws to properly install these units. Attaches spark plug wire holder to the factory finned aluminum valve covers

Exact Copies Made From the Original Supplier to Ford Motor Co. U.S.A. Made. Ramp-Lok Features a Special Conical Washer Designed Specifically for Exhaust Manifolds.

Replaces Ford Part #: EV-51 or D0OZ-6A666-A

Replaces Ford Part #: D0ZF-12450-A

Hex bolt for attaching fuel line clips. 5/16-18 bolt. See related items for reproduction clips.

Reproduction 60000 Mile 6 Month Lube Sticker for the 1967 - 1973 Mercury Cougar / Ford Mustang

Reproduction inner "A" pillar panel and fresh air vent vent panel set for the driver side (left hand) of the Mercury Cougar or Ford Mustang. This item features weld through primer and is ready to install. Unfortunately both Cougars and Mustangs alike are prone to rust in these areas, so finding a nice original piece can be difficult. We're delighted to have this high quality panel set to offer you the perfect pieces to replace those rusty units you have now!

Reproduction inner "A" pillar and fresh air vent panel set for the passenger side (right hand) of the Mercury Cougar or Ford Mustang. This item features weld through primer and is ready to install. Unfortunately both Cougars and Mustangs alike are prone to rust in these areas, so finding a nice original piece can be difficult. We're delighted to have this high quality panel set to offer you the perfect pieces to replace those rusty units you have now!

Here is our A/C dryer decal for your Coug or Stang equipped with A/C. Replaces Ford part #: D0AA-19959-C3.

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade A used may have a minor stress crack or small chip. The holes for attaching duct work will be good. See Grade B for a lower cost version. 

Air conditioning fan blower BARE clam shell assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. Assembly comes as shown: fiberglass two piece housing, flapper door, and a couple of clips to hold it together. Grade B used will have a minor stress crack, and or small chips. The holes for attaching duct work also may have one hole blown out. See Grade A for a better condition version.

Air conditioning fan blower assembly for any 1969-70 Mercury Cougar or Ford Mustang with factory A/C. We offer this assembly to go along with the reproduction heater box with air conditioning. Assembly comes as shown: fiberglass housing, fan motor, fan motor mounting plate, fan wheel, fan motor resistor, and the one attached vacuum actuating valve. All components tested and working, housing used and may have a chip or small crack from 5 decades of use.

Tecumseh compressor for air conditioning systems for Mercury Cougars and Ford Mustangs. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. These Tecumseh compressors came with a front oil fill plug up until 1967, thereafter, they have a top fill plug. Top fill is the most common, and likely what you will receive, unless you specify the 1967 style with front fill. These units are shipped without pulleys, clutches, or valves. The...

York compressor for air conditioning systems for Mercury Cougar and Ford Mustang. These should be professionally inspected or rebuilt and our compressors have all been in storage for some time. Shipped without pulleys, clutches, or valves. The York compressor is constructed mostly of aluminum and is lighter than the Tecumseh brand compressor by 10 pounds. The York compressors are less common too, subject to availability. We often see part numbers on the York tag (which does not list a Ford...

Used air conditioning evaporator core, for most of the 1969 model year and all of 1970. You will need to make a comparison with your A/C box or old evaporator for selection. Personally, for the money, I would prefer a good used original copper tubed coil over a cheesy import that uses aluminum. That is because the aluminum is way more prone to corrosion when compared to the copper unit. We only sell used coils that are clean and sealed and do not sell coils that have pest damage or have...

Exact replacement to original dryer. Drier removes moisture and should be changed anytime system is recharged. It is the life of your system. Stainless steel filter element. Filter stops contaminants from clogging expansion valve. Replaces part # C9ZZ-19959-A.

This unit is a reproduction concours correct A/C discharge hose for your Cougar or Mustang.This hose is compatible with both 134a and R12 refrigerants.

Regardless of which V-8 engine, C9ZA-19972-C or C9ZA-19972-E, both are the correct part number. This hose is approximately 20 inches long. Ford part # C9ZZ-19972-C.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine from 1969-73. Original condensation drain hose from the A/C case, through the floor board, to the ground. Replaces Ford part # C9ZZ-19858-C.

For Mercury Cougar and Ford Mustangs with integral or factory installed air conditioning with any V-8 engine. Original condensation drain hose from the A/C case, through the floor board, to the ground. Correct "S" shaped moulded hose with restrictor intact. Ford part # C9ZZ-19858-C.

Regardless of which V-8 engine, C9ZA-19837-A or C9ZA-19837-C both are the correct part number. This hose is approximately 68 inches long. Ford part # C9AZ-19837-A.

Here is your concours correct A/C suction hose for your beloved Mercury Cougar or Ford Mustang.This hose is compatible with both 134a and R12 refrigerants.

A/C suction line for the evaporator to compressor for the 1970 Mercury Cougar or Ford Mustang with any V-8 engine. This hose is approximately 55 inches long.Ford part # D0ZA-19867-A and MPC # D0ZZ-19867-A.