1970 Ford Mustang

Oil pan baffle as found on all 1969-70 Ford and Mercury products with R or Q code 428CJ or 428SCJ engines. This baffle is sandwiched between the oil pan and the block.

This is the 3 hole version of the ball joint for the 1967 - 1973 Cougar and Mustang. Right is same as left. Two required per car. Hardware included. made in Tiawan.

D0ZF-9600-M Air cleaner base for all 351C engines, both H code 351C-2V and M code 351C-4V engines. Could also be found under casting number D0ZF-9600-Z. About 17-3/4" inches in diameter (although the Ford MPC shows it to be 17.00 inches). *Excludes 1970 351-2V Windsor engines. Ford part number D0ZZ-9600-M.

D0ZF-9600-B Air cleaner base for 1970 H code 351-2V Windsor engines. About 17.84" inches in diameter. Ford part number D0OZ-9600-B. *Excludes 351C Cleveland engines. Click on images to enlarge. ...

Reproduction group 27 battery heat shield that fits many Mercury Cougar and Ford Mustang applications from 1967-70, on most hi-performance engines. It was often the first part discarded but serves a real purpose. Nice American made part, stamped with Ford numbers C7ZB10A682B and C7OB10A682B. There is also a D0... sized for group 24 heat shield offered for 1970-73. *Trivia - these battery heat shields were often trimmed down to fit group 24 batteries.Click on the link below to find some...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. For any 1970-71 Mercury Cougar or Ford Mustang with 302 or 351 engine and 43-55 AMP alternators. The originals were either 43-55 Amp (Standard) Draw or 65-70 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces...

Each of these great kits include all three required cables, including part numbers, proper terminal and post clamp ends. Starter cables are properly shielded from heat. 1970-71 Mercury Cougar with 65-75 AMP alternators and V-8 engines. The originals were either 43-55 Amp (Standard) Draw or 65-75 Amp (High) Draw. We recommend going with the High Draw. As one customer put it, "These [standard draw cables] look anemic." (Thanks for the feedback Charles!) Replaces Ford Part # : D0ZZ-14300 ...

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

This battery cover is designed to be used with any maintenance free flat top battery **24/60 series with original terminal location for the Autolite battery covers.

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

Fits Standard and XR7

Perfect fit the first time. You will be happy with this Group 24, quality reproduction and check out the price! These battery trays are a popular item for restorers since most of the originals have been destroyed by leaking batteries over the years. Replaces Ford part #: C7ZZ-10732-D.

Good used group 24 tray for 1968-70 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray, for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting).

This is what I consider to be "Premium Quality". Very correct in every detail and made in the US! The group 27 larger tray was optional on any Cougar and standard on big block Cougars. Replaces Ford part # C9ZZ-10732-AR

Concourse Correct with 22, 24 & 27 series batteries for Mustang, Cougar and Shelby GT350/500 made in the USA to original Ford Specifications, includes attaching bolts. Replaces Ford Part # C9ZZ-16060-A or C9ZZ-16052-P .

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

New front Inner wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 1.378 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A smaller outer bearing and this inner bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

New front outer wheel bearing with cup / race for original drum and disc brakes for all 1970-73 Mercury Cougar and 1970-73 Ford Mustang with V-8 engines. These are tapered bearings with cone or race. Inner diameter is 0.865 inches. These are dry bearings, meaning they will need to be packed with chassis bearing grease, prior to installation. A large inner bearing and this outer bearing are required for each side. Two of each needed for the front wheels. *Note - This bearing only fits the...

Reproduction steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. Outside diameter: 1 1/2" Inside diameter: 1 1/4"*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used lower steering column bearing for the 67-73 Cougar or Mustang. The tilt columns take an upper and lower bearing, while the fixed column only takes an upper. The upper bearing can be found here. Outside diameter: 1.500"Inside diameter: 1.060" *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. For use with 164 tooth flywheels. For use with all 1968 302 engines and 1969 - 1970 Boss 302 Eliminators. Cast aluminum construction. Shipped bare, no hardware or clutch fork. Search words 68 69 70 small block F J G code. Ford part number C5AZ-6392-BCasting number C5AA-6394-B *Note - This is not a replacement for 1970-1977 Ford Maverick or Mercury Comet 302 engines. See part C5DA-6394-A with 157 tooth flywheels. ...

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C5TA-6394-A. For use with any 351 Windsor or 351 Cleveland engine for the years 1969 and 1970. Cast iron construction, for use with 164 tooth flywheels. Shipped bare, no hardware or clutch fork. Search words: 69 70 H M code engine Eliminator XR7 Sport Special

Eight piece kit that includes inner and outer belt-line for both door and quarter glass. This kit contains enough for both pieces of door and quarter glass. These strips run horizontally against your glass and keep water and debris from entering your rear quarter panels and doors causing them to rust out. These kits include the correct stainless steel trim on the interior side strips. Old belt-lines will become hard and trap grit causing your glass to get heavy vertical scratches. You can...

Very nice replica of the cigar / cigarette lighter bezel for the 1970 Mercury Cougar or Ford Mustang. Replaces Ford part # D0ZZ-10852-L.

Nice reproduction globe box door button bezel for all 1967-70 Mercury Cougar and Ford Mustangs. We do sell used to, see related.Replaces Ford part number C6OB-62060A12.

This trim ring that surrounds the glove box release button is often missing. Easily installs by snapping in place. Better fit than the reproductions out there.Replaces Ford part number C6OB-62060A12.

Replaces Ford part #: C9ZZ-10852-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Here's another quality reproduction with the correct camera case finish used on all 1969-70 Mustangs and Cougars except Xr7. Replaces Ford part # C9ZZ-6504774-B.

Replaces Ford part #: c9zz-10852-w. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Used wiper switch bezel for any 1969-70 Mercury Cougar or Ford Mustang. This is a used bezel that has been inspected for pits in the chrome. This used unit will likely have one of the rear orientation tabs broken, but other than that it will be a good used part. Excellently priced, compared to the reproduction. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. Replaces Ford part #: C9ZZ-10852. ...

Bleeder screw for your 1968 - 1973 Cougar or Mustang Calipers.

Used heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These are good used original FoMoCo units and have the correct pigtails in place. This used unit also carries a one year warranty compared to the reproduction that carries a 30 day warranty. The mounting plate is included and mounted to the motor. On the reproduction units, the mounting plates are sold separately. These are the 1969-70 variety, which have specific colored wires and leads....

Reproduction heater blower motor for Mercury Cougars and Ford Mustangs with integral or factory air conditioning. These off-shore units may or may not prove to be as good of value as our good used original FoMoCo reconditioned units. Notice they do not have the correct pigtails in place. To date, all we can find for these cars are foreign made units. Keep in mind our used units carry a one year warranty and these new motors have a 30 day warranty. Also know that the mounting plate is included...

Used rear defog blower motor with integral fan. Ford supplied these for many years, some have different connectors on them. Some have the square style as found starting in 1973. We have a good supply of working and tested motors, so request the type of plug end you need.Replaces Ford part number C8AZ-18527-A and D3AZ-18527-A.

Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.

These Spark Plug Wire Separators are made of high-quality ABS plastic. Constructed to hold both standard 7mm and 8mm high-performance spark plug wires. Fits directly on valve cover clip. Available in blue, red and OE black.

Body assembly manual used by the workers when they were originally building the Cougar and Mustang. Must have if you are putting together your Cougar or Mustang, and a great resource when tearing it down!

Black phosphate body bolt for various applications on 67 - 73 Mercury Cougars and Mustangs. These bolts can be used anywhere you have J-nuts, including but not limited to fenders, inside your headlight buckets, and even in your center grille piece on the 67 - 68. Bolt size: 1/2"-18 X 1-3/16"

New rubber body plug, fits 1-3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Typical application is rear leaf spring access.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377356.

New rubber body plug, fits 1-1/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some of the holes include: inner frame rails at radiator, center of firewall, and side of cowl.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377936.

New rubber body plug, fits 3/4 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: frame rails at sway bar, rear floor pan, LH fender apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377977.

New rubber body plug, fits 9/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles, typically they are for: front fender aprons, transmission cross member, and radiator support. Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 376966.

Reproduction rubber body plug for the Mercury Cougar and Ford Mustang. This 11/16" x 15/16" oval unit fits to the top of the cowl underneath the front fenders. These little units are sold individually, and their are usually two required per car. Replaces Ford plug marked 383181-S.

New rubber body plug, fits 13/16 inch normal gauge sheet metal panel holes. These are found on various places throughout classic Ford and Mercury vehicles. Some locations include: trunk floor pan, side of cowl at door, and LH apron.Sold individually, also sold in kit or assortments for Cougar and Mustangs.Replaces Ford plugs marked 377949.

New rubber body plug, oval , fits inner frame rails. 3/4" x 1" oval holes. Sold individually, Usually 2 per car. Fits 1967-73 Mercury Cougar and Ford Mustang.Replaces Ford plugs marked 378770-S.

44 Piece kit that includes quarter panel drain plugs.

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1969-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Some time between 1969 and 1973 this plate underwent a revision by Ford. We are going to split by generation. 1969-70 plates are flat on one edge. 1971-73 has a slight hump or bend. Either works and...

These are about half the weight of originals and do not look correct in any way. They are far better than nothing. Bolts to the left hand and right hand lower floor reinforcement panels. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. Replaces Ford Part # C5ZZ-7610962-A. The Ford description of this plate is "Plate - Front floor lower cross member". All 1969 - 1973 Cougar convertibles and all 1965 - 1973 Ford Mustang...