1970 Ford Mustang

Ready to clean up and install, not bent, tight joints, minimal surface rust.

Upper toque box patch panel plates for the 67-70 Cougar Coupe or 65-70 Mustang Coupe or Fastback.

Reproduction passenger side (left hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) torque box for Mercury Cougar and Ford Mustang convertibles.Here's our little film to help you fortify your flexxy feline!

This is a reproduction 3 piece non assembled torque box for the driver side on the 69 - 70 Cougar or Mustang Coupe. The benefit of getting a non assembled torque box is that you'll find installation much easier as compared to the pre-assembled boxes.  Included are inner and outer panels and gusset. Passenger side non-assembled torque boxes are not available.

Reproduction torque box gusset for your 67 - 70 Cougar or Mustang. It is the reinforcement bracket that attaches to the bottom of the torque box for extra strength. Sold as a pair.

Driver side (left hand) outer section of the torque box for the Mercury Cougar and Ford Mustang for both coupe and convertible.

Rebuilt C6 FE Engine torque converter for the 1967 - 70 Mercury Cougar and 1966-70 Ford and Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core. 1966-70 Ford FE engines include: 352, 360, 390, 427, 428, etc. Ford part number C8OZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad...

Rebuilt FMX torque converter for the 1969 - 73 Cougar or Mustang. This item carries a $200 core charge, refundable when we receive your rebuildable core.Ford part number C9ZZ-7902-A. What does it mean to “rebuild” a torque converter? When there are problems with a car’s automatic transmission, sometimes it’s the torque converter. It could be fluid loss, bent vanes, or bad bearings among other problems. We have a local shop with decades of experience do a very thorough rebuild that is...

NOS Autolite 4300 training handbook. Filled with details pertaining to operation, adjustments, overhaul and servicing of the Autolite 4300 carburetor which was used starting in 1967.  Volume 67 S2 L2, 9503.1, 9503.2

This kit is an easy way to covert your 289 / 302 / 351W engine from a C4 or C6 transmission to an Automatic Overdrive Transmission. Kit includes: Cross memberTrans Mount InsulatorSlip YokeKick Down CableFlex Plate AOD Shift Linkage This is just the kit, and does not include the full transmission!

Core C6 transmission for a 1970 Mercury Cougar or Ford Mustang, with Q or R code 428CJ engine. Tag number PGB-AF2. Floor shift C6 Transmission. Core transmission only, NO dip stick, dip stick tube, or torque converter. This is a rebuildable core transmission, removed from a 1970 Mercury Cougar with 428CJ engine. Main case inspected for damage. Heavy item, in most cases it can ship UPS ground. Easier if picked up in person.

Used C-4 transmission 90 degree brass fitting for the rear oil cooler line. Fits 1967-68 Mercury Cougar and 1965-73 Ford Mustang where applicable.Not all of the transmissions had a 90° fitting. Compare with your cooling lines.

Reproduction transmission cooling lines for the Mercury Cougar or Ford Mustang equipped with the C-6 automatic transmission and 428CJ engine. These are sold in pairs.

Fits all applications for both automatic and manual transmissions, big block and small block. Will also work with your Tremac / T-5. Replaces Ford part # C4DZ-6068-A.

New manufactured transmission oil pan for the Ford C6 transmission as found on 1967-73 Cougar and Mustangs, big block and small block engines. Very high quality heavy gauge steel.Replaces Ford part number C6AZ-7A194-A.

Reproduction transmission selector tube seal for the 69 - 70 Cougar or Mustang steering columns.

New manufactured transmission slip yoke for either C-4 automatic transmission or small block manual 3 or 4 speed manual transmissions. Ford 1965-1973. 28 splines and 1-1/16" U-joint caps.

New manufactured transmission yoke for a T-5 5 speed transmission.

Application all 1967-1968 289/302 engines with C4. 1967-1973 small block V-8 with 3 or 4 speed manual transmissions. Features 28 splines. Some have a casting number of C5AW-4888-A.Excludes Hi-performance V-8's such as Boss 302, 390, 428CJ, and C-6 / FMX transmissions.

31 Spline transmission slip yoke for all 1969 351-2v/4v and 1970-1973 351-2v FMX  cars.  *Excludes 351C-4v and 351CJ engines.

Reproduction transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy our used support, as these reproductions are inferior to the originals, and to be honest, they simply do not fit well.

Used transmission support for 67 - 70 Cougars and Mustangs. We strongly recommend that you buy this used support as compared to the reproductions. The repros we offer are inferior to the originals, and to be honest, they simply do not fit as well.

Reproduction emergency / parking brake pedal pad trim piece for the Mercury Cougar or Ford Mustang. This great little reproduction looks good and is one of the little detail pieces that can separate a nice car from a mint car.Replaces Ford part # C9ZZ-2A487-C.

Used emergency / parking brake pedal pad that features all stainless steel construction. This unit cleans up very well with fine steel wool, has reusable folding tabs, and is easy to install. A great piece to finish off your interior!Replaces Ford part # C9ZZ-2A487-C.

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT.Clear, high strength adhesive for use with lightweight fabrics and carpets. Heat and moisture resistant.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Reproduction trunk wheel house seam cover for the Ford Mustang. I have actually never seen an original pair of these on a car, but they do serve a purpose if you are in the habit of cramming your trunk full of items you do not want scratched. These attach to the protruding seam where the inner and outer wheelhouse bond together and measure about 14" in length. You will have to modify these to fit your Cougar. Only sold in black. Replaces Ford part # C5ZZ-6531466-A.

Reproduction oil pressure remote sending unit tube assembly. For all 1969-70 Mercury Cougar Eliminators with G code Boss 302 engines, and 1969-70 Boss 302 Mustangs with oil pressure gauge.The book says 'without tachometer'. Boss 302 forum suggests that it is for a remote oil pressure sending unit. According to a Boss 302 Engine Detailing article co-written by Marcus Anghel and Bob Perkins, this tube was needed for the larger bell shaped oil pressure sending unit. The larger bell shaped oil...

Reproduction machined tube seat set, for all 1968-70 Mercury Cougar and Ford Mustang. Also some 1967 Cougar or Mustang control valve and ram cylindernwith the 5/16" fittings. This set includes 6 seats, other kits only include 4 seats. Please note that early 1967 control valves had 1/4" fittings.

Very nice quality reproduction turn signal lever, though the detail on the end is slightly different from the originals. Most will not notice the difference. We do get good used units in stock occasionally. Replaces Ford part # C7ZZ-13305.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he...

Good used turn signal stalk with no rust or peeling chrome. The 1970-73 with tilt column used a stalk with an additional plastic bushing near the base. This used unit is only for the person who cares about originality in the smallest of details as our repro is a decent piece, just not exact.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

Sold individually. Has correct flattened area at top. Competition handling size, measures 7" from inner radius to end of threads. Thread size 7/16-20".  Does not include the OEM style nuts, those are an optional addon.  Replaces Ford Part #: C6OA-5705-C

These coarse thread nuts have an integrated lock washer with serations for the Mercury Cougar or Ford Mustang. They will ONLY work with the U-Bolts used in conjunction with the lowering kits. The thread size is 7/16"-14. *NOTE* Eight of these are required per car and are sold individually.

Permatex Ultra Copper Sensor Safe High temperature silicone, good for any makes and years. This stuff won't harm your Oxygen Sensors, and is good for up to 700 degrees intermittent. 

New heavy duty rubberized undercoating for the Mercury or Ford. Heck, it can be used on ANY car. This body shop proven formula is used to protect against road salt, moisture and corrosion. To be used on the inner aprons and fenders, frame rails, fuel tanks, rocker panels, under hoods and firewall. Basically, anything you want to protect under your pride and joy will be encapsulated and protected with this heavy duty rubberized undercoating.

Designed by an engineer and original owner of a 1970 Cougar convertible, this brace is ideal for those wanting to brace their car prior to removing key structural parts. It was designed for a 69-70 Cougar Convertible but will work well on any 67-73. We Strongly suggest that once you are done with this item you return it for a 80% refund as this is our only unit at present and we want as many folks as possible to benefit! Thank you Dan Pobloskie in North Prairie, Wisconsin for sharing your...

OEM Style Universal Exhaust Hanger Bracket 1967, 1968, 1969, 1970, 1971, 1972 and 1973 Mercury Cougar and Ford Mustang

Replaces Ford Part # C1AZ-4529-A Sold individually. All applications, attaches the drive shaft U-Joint to rear end pinion yoke. 5/16 Inch Diameter #24 thread for 1 1/8 inch Bearing Caps.

All applications, attaches the drive shaft U-Joint to rear end pinion yoke. Sold in pairs, complete with nuts. Perfect used. Ford Part #: C1AZ-4529-A or D3AZ-4529-A.

This reproduction universal joint is forged from high strength alloy steel that is crossed w/ an anti-corrosion coating. This unit also features a grease fitting for an extended life, and fits Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E. Span 3.30" cups 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number...

Reproduction universal joint that fits the transmission end of the drive axle on the Mercury Cougars and Ford Mustangs equipped with the 289, 302, 351 Windsor and most 351 Clevelands (see chart). this unit includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-C or C3AZ-4635-E. *NOTE* Part number C3AZ-4635-C was discontinued in 1968 and was replaced by C3AZ-4635-E.

Reproduction universal joint forged from high strength alloy steel that is cross w/ an anti-corrosion coating. This unit fits the transmission end drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (See Chart). this unit also features a grease fitting for an extended life. span 3.60" cup size 1.00" and 1.00"  Replaces Ford part # C3AZ-4635-G.

Reproduction front universal joint that fits on transmission end of the drive axle on Mercury Cougars or Ford Mustangs equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes a grease fitting for an extended life. Replaces Ford part # C3AZ-4635-G.

Reproduction universal joint forged from high strength alloy steel and crossed w/ and anti-corrosion coating. Fits the differential end of the drive axle on all 289, 302, 351 Windsor as well as most 351 Clevelands (See Chart). Includes a grease fitting for an extended life. 3.25" span cups are 1.12" and 1.00" diam. Replaces Ford part # C3AZ-4635-F.

Reproduction alloy rear universal joint for the Mercury Cougar or Ford Mustang. This unit is forged from high strength alloy steel crossed w/ an anti-corrosion coating. This universal joint fits the differential end of the drive axle on all Eliminators and cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. span 3.5" cup size 1.00" and 1.12" Replaces Ford part # C3AZ-4635-H. ...

This reproduction universal joint fits the differential end of the drive axle on all Eliminators and other cars equipped with the 390, 427, 428, 429 and some 351 Clevelands (see chart). Includes grease fitting for extended life. Replaces Ford part # C3AZ-4635-H.

For fixed steering wheel. Special molded rubber sleeve that holds the bearing in place. Exact reproduction. Replaces Ford part # D1AZ-3518 or E2AZ-3518