1968 Ford Mustang

Reproduction driver (left hand) side drum brake self adjustor repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Reproduction passenger (driver hand) side drum brake self adjuster repair kit for your Mercury Cougar or Ford Mustang. This kit contains all the parts necessary to refurbish the self adjusting mechanism on drum brakes. Includes new cable and guide, ratchet, spring, and all necessary small parts. Kits include everything for one wheel.

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved.  Sold in a box of 100, we also list them individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71...

Every now and again, the studs that hold the rear moulding begin to rust and break away from the body of the car. No need to install your rear window trim with missing studs and clips......just screw one of these little guys into place and Viola! Problem solved. Sold Individually. #4-24 X 3/8" 7/32" Head Diameter Phillips Flat Head If you were missing every stud on your windows, you would need: 67 - 68 = 22 front, 20 rear 69 - 70 = 13 front, 24 rear 71 - 73 = 16 front, 18 rear Here's a handy...

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1967-68 Mercury Cougar and 1965-68 Ford Mustang.Ford part # C2OA-18591-A or C8ZZ-18591-A*Note - Excludes Heater with integral or factory air conditioning.

This direct replacement resistor is used between the heater switch and the blower motor. These often fail and prevent the blower motor from turning on. Replaces Ford part # C2OA-18591-A. 1962 - 1967 Ford Fairlane1962 - 1964 Ford Galaxie1964 - 1966 Ford Thunderbird 1967 Ford Mustang 1968 Ford Mustang ...

New heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Replaces part # C7ZZ-18591-B.

Used heater blower motor resistor for Mercury Cougars and Ford Mustangs equipped with factory A/C. This unit attaches to the heater blower fiberglass housing. Ford part # C7ZZ-18591-B.

Replaces Ford Part # C8AZ-2066-A Sold individually

Used cigar or cigarette lighter threaded retainer with ground lug. Fits any 1969 Mercury Cougar and Ford Mustang with factory installed console. The ground lug is needed for the heating element in the socket. The consoles are made of plastic and use the common socket designed for steel dashes. This retainer is part of C9MB-15055-A socket and retainer assembly. 

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

Used on the ignition lock cylinder. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang.

Used rear retainer for the ignition lock cylinder on any 1967-68 Mercury Cougar or Ford Mustang. Good value, used as they come out of the cars, will have some flash rust since they were never plated or painted, usually it will not come with the small screw. This unit locates and maintains the angle to the dash from behind. Attaches with one small screw, and the bezel and retainer nut secures the whole works to the dash from the front. 1967-68 Mercury Cougar and Ford Mustang. 

Push on retainer for rear drum brakes. 2 or 3 of these were used to hold the rear brake drums onto the rear axle assembly during construction of your 1967-73 Mercury Cougar or 1965 - 73 Ford Mustang. While not necessary, these are a neat concours item. Sold individually.  Ford part number 372188-S

Cougar actually used a larger ribbed plate on manual transmission cars without a console but this Mustang part is an inexpensive alternative. The rubber shift boot screws to the transmission tunnel, carpet then goes over it and lastly this retainer slips over the boot and hides the cut edges of your carpet. Shift boot sold separately.Replaces Ford Part #: C5ZZ-7262-C.

Nice reproduction clip for attaching the speedometer cable onto 3 and 4 speed 1967-70 Mercury Cougar and Ford Mustangs. Mounts to the firewall.

Used steering column tube retainer for the 67 - 69 Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. These little units help hold the steering column together and there are 3 required per column. Sold individually. This are not advisable in the 1970 and later cars. Ford part # C7SZ-3499-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Reproduction lower ball joint retainer and gasket. Works on 67 - 73 Cougars and Mustangs.

Reproduction retainer clip for the back up light switch wiring on the 67 - 69 Cougar or Mustang equipped with a 3 or 4 speed transmission.Replaces Ford part number C7ZZ-14163

This reproduction clip secures the clutch pedal rod end as it comes through the clutch pedal hanger.  Keep in mind that this reproduction is a different size compared to the original (see comparison above) and will need to be modified to make fit. As always, we recommend going with original used parts. You can find it here. Replaces Ford part number C8AZ-2B277-A ...

Plastic insert with metal locking retainer. Replaces Ford part # C5AZ-6221952-A. NOTE* This clip will need to be squeezed on the clip side in order to obtain a good grip. Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Plastic insert with metal locking retainer. The plastic came in various colors, white, red, and black are common. Replaces Ford part # C5AZ-6221952-A.Check out our handy diagram below to find other '67-'68 door parts you may need. All the item numbers shown can be typed in to the search bar on our site. (Click image to view full size) ...

Reproduction emergency / parking brake retainer clip set for the Mercury Cougar or Ford Mustang. These units are sold in a set of 3.

Used door lock and trunk lock cylinder retainer clip. Not exactly the same as the door lock clips. Trunk clips have the small hole, a hooked tool would be used for removal. Not used on 1967 - 1968 Cougar trunk lock cylinders. *Note - For use on Cougar trunk locks built prior to 3-1-1972. Please see Ford part number D2WY-6243629-A for your Cougar needs on cars built after 3-1-1972 (used only).

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.

Used retaining bolt with nut for the fixed column on any 67 - 68 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together.  Sold individually, 2 per column.

Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade A's will have no scratches or dings.Ford part number C8ZZ-17B719-A

Used grade A side mirror retaining nut for the 1968 Mercury Couga or Ford Mustang. Grade B's will have minor scratches or dings. Ford part number C8ZZ-17B719-A

Replaces the original Ford part that features a # C7SB-17B732-A casting number. Basically correct for 1967 but works just as well on 1968 mirrors. These nuts are are not 100% correct for a 67 or 68, kind of a mixture of both.Very nice chrome quality at a reasonable price. NOTE: Our mirror nut removal tool works & fits perfectly with the original mirror nuts. However, you will find the tool will NOT fit this reproduction nut properly, it will require that it be filed a...

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Replaces Ford part #C0AZ-9A307-B.

Good used ring with only surface rust and no obvious gouges.

Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.

Used retaining spring and two screws for attaching the break away air conditioning vents to any 1968 Mercury Cougar or Ford Mustang with factory installed A/C.

We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....

These are economy replacement hoses by Scott Drake. Aftermarket type hoses without original Ford markings in most cases. Made in the U.S.A. This hose is the hose most Mustang / Cougar parts vendors offer. It is a rubber flex hose with economy fittings. Use caution when tightening these down as they are susceptible to stripping if you torque them to the specs called for by FORD. We do not recommend these hoses and can not stand behind them as they often will leak if not torqued to the proper...

Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.

High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...

Reproduction hood latch return spring, attached to the sides of the hood latch on the 67 - 68 Cougar. Sold individually, 2 required for Cougar, 1 for Mustang.

Reproduction ring gear for 157 tooth fly wheels and flex plates as found on certain 289 and 302 engines in 1967-68 Mercury Cougar and Ford and Mustang. Quality new ring gear, check the Youtube for installation instructions.

Reproduction ring gear for 164 tooth fly wheels and flex plates as found on 1968-73 Mercury Cougar and Ford and Mustang. Quality new ring gear, check Youtube for installation instructions. 

Reproduction ring gear for 184 tooth fly wheels and flex plates as found on big block 1967-71 Mercury Cougar and Ford and Mustang. Quality new ring gear, check the Youtube for installation instructions. Typically, the engine sizes would be 390, 410, 427, 428, and 429 cubic inches.

We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...

Correct rivets for use after you have painted your car or installed a new door. No special tools needed for installation. Simply lightly tap the center recessed portion with a small bolt or blunt punch. If your plate is missing you can obtain a correct reproduction with your unique codes at www.martiauto.com. Sold as a pair. Replaces Ford Part #: C5ZZ-6223000-A or 354921-S.

Inner rectangular clip to hold on the rocker panel moulding on a 1967 or 1968 Ford Mustang or Mercury Cougar. Sold Individually.NOTE - We've found that these reproduction clips do not work as well as the originals, you may find it a bit hard to install the rockers onto these clips without having to apply too much pressure, causing unwanted bending.