1968 Ford Mustang

These beautiful reproductions replace those rusty and corroded originals that just look nasty. 5/8" Replaces Ford Part #: C6AZ-18599-B

These beautiful reproductions replace rusty and corroded originals that just look nasty.5/8" Replaces Ford Part #: C6AZ-18599-S

These bright beautiful reproductions replace those corroded and rusty originals that just look nasty. Replaces Ford Part #: C8AZ-18599-C

Reproduction water inlet elbow for your 1968 big block Cougar or Mustang.Replaces Ford Part #: C8AZ-18599-AClick on images to enlarge. ...

Replaces grommet in chrome oil cap with PCV valve. Inside diameter is 37/64". Replaces Ford part #: C8AZ-6892 or C8AZ-6A892-A.

Reproduction electric rear deck / trunk lid release. Includes electric lock latch, control knob and wiring needed to install.Detailed instructions included.

3/4" wide and 60' long. This tape resembles the tape you would find on bicycle handle bars or a hockey stick but is in fact different. The taillight harness uses this type of tape as well as portions of the under dash harness. Not used in modern applications and getting rather hard to find these days.NOTE: This is FRICTION tape not adhesive tape. It is coated with rubber and relies on friction with itself to wrap wires. It does not stick to the wires. This was one of the first types of...

Used electrical contact kit for the foot operated electric wiper actuating device. Most times these contacts have been fried

Used 14x6" Eliminator wheel with a chrome center and a painted rim for the Mercury Cougar or Ford Mustang / Torino. This chrome version was never used on a factory ordered Cougar, but you could order it as an over the counter upgrade as shown in 1968 dealer promotional literature. Total width is 7" and the backspacing is 4". Click here for the hubcap and trim ring we recommend for this wheel.

Used 14x6" Eliminator wheel that had a painted center and rim from the factory for the Mercury Cougar or Ford Mustang / Torino. For those wanting original FORD dated codes and riveted together construction (reproductions are welded) this is a good used wheel in need of paint. Center cap and trim ring sold separate. Click here for the hubcap and trim ring we recommend for this wheel. Ford part # C8OZ-1007-J.

This Super Cobra Jet emblem was never used on a Cougar, but is the Cobra Jet emblem used on the Hood Scoop for 1969-1970 Mustangs. It is also an attractive emblem for your custom application. Thanks for the plug Mark!: "My first deal with Don was clear back in the 1980s and I have sent a few people his way and all came away happy. While at his shop on Monday I watched Lin crawl under a convertible, phone in one hand and a tape measure in the other, and measure a cross...

These are sold individually, two required per car. This is the aluminum emblem / decal which mounts on the center of some late 67 and all 68-73 scuff plates. Features raised script like original. Adhesive backed with a protective coating that peels off after installation. Replaces Ford Part #: C7ZZ-6513208-T. Licensed by FORD ...

Reproduction steel emergency / parking brake adjustment rod for the Mercury Cougar or Ford Mustang and is threaded for full adjustability. Replaces Ford Part # C7ZZ-2628-B.

This reproduction driver side (left hand) emergency / parking brake cable fits from the equalizer to rear brakes. 1 required per vehicle. The cable length is approximately 29-1/2". Cougars manufactured after 2/69 may use the 1970-73 left hand cable. It is easy to check by measuring the cable. The 1968 cable is just over 29" long, and the 70 cable is just over 32" long. Click on the image to left to see the difference. The 1968 style of emergency brake cables can be used on the 1967 cars, as...

Reproduction emergency / parking brake assembly that is a complete system and ready to bolt in. Looks better than even our grade "A" used one at first glance, but this off shore unit will never hold up as well as our original FoMoCo good used units.

Used emergency / parking brake assembly for a Mercury Cougar or Ford Mustang as removed from a West Coast Cougar organ donor. This unit may have some minor rust. Normally we assemble with reproduction cable.Ford part # C7ZZ-2780-B.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for LH or DRIVERS side original part Ford number is C9ZZ-2A638-A.

Used parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for LH or driver side is C9ZZ-2A638-A. This unit is from a solid Western parts car, so you won't be getting one of those rusty East Coast units! Ford part # C9ZZ-2A638-A.

Reproduction parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. 1967-73 Mercury Cougar or most Fords including Mustang. Fits 10 inch drum rears. Replacement part number for RH or passenger side original part Ford number is C9ZZ-2A637-A.

C9ZZ-2A637-A Parking brake lever that mounts between the parking brake cable and secondary brake shoe in your rear brake drum assembly. Ford service replacement part number for RH or passenger side is C9ZZ-2A637-A. Clean Western part with no heavy corrosion like you see on Eastern cars.

Reproduction 10" parking brake link. Spring included. Sold individually, two per car. Replaces part Ford Number C2OZ-2A642-A

Parking brake link. The spring (not included) is wound in a rectangular shape to fit the one end of the link. Ford part # C2OZ-2A642-A.

Holds both both the speedo cable and the parking brake cable in place with two self tapping bolts. Bolts not included, picture is for reference only. Part will have rust, but not severe.Replaces Ford part number 381821-S2 per the Chassis Assembly Manual 1967 page 17, 1968 Page 39.

This is the first bracket to secure the emergency brake cable as it exits the firewall. It mounts to the frame rail. It is held on by one bolt which is not included, picture is for reference only. Part will have rust but not severe.

Used Emergency Flasher Knob Bezel / Fixed Column for the 1967 - 1969 Mercury Cougar / 1967 - 1969 Ford Mustang 

Correct for your 1967-68 Cougar or Mustang with A/C, but will work just fine in all 1969-73 Cougars and Mustangs with A/C. These pieces are also an excellent option for 1969-73 Cougars and Mustangs without A/C because it will give your heater core a better tighter fit inside the heater box. If you choose to go this route on your 69-73 non A/C car, slight modification to the ends caps will be required to fit. Your just going to cut a hole in one of the end caps. Easy cheesy, no sweat.These are...

Front sway bar end link kits for all classic Cougars. 1967 - 1973 Kit includes spacer, bolt, insulators, nuts, and washers. All new hardware. Kit includes 2 links. Replaces Ford part # C2OZ-5A486-A.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 6C5, March 5, 1966.  Used 0.030 over bore 4.080" Ford 390 engine block. Bare block, no crank shaft. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7M27, December 27, 1967.  Used 0.030 over bore 4.080" Ford 390 engine block. Years ago, it looks to have been fresh machined, with new freeze plugs. No paperwork, bare block. Will be used, dirty. Good for rebuild or assembly, quality of machining unknown. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 6L15, November 15, 1966.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

This block has been professionally hot tanked and mag checked. No cracks. Dated 7C16 March 16, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship through any conventional methods (USPS, UPS etc). Along...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Dated 7C29 March 29, 1967.  Used standard bore 4.05" Ford 390 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6ME, C7ME, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  This item cannot ship...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY.Used standard bore 4.00" Ford 289 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, may have C6AE, C8AE, castings. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping.  Dated 6K19 or October 19, 1966.  C6AE-6015-G. This item...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 8D15 or April 15, 1968. This item cannot ship through any...

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Used standard bore 4.00" Ford 302 engine block. Will be used, dirty, have measurable taper, and will have a ridge. Good for rebuild. Bare block, will have C8OE, casting. When we have them in stock we will post the casting date or dates. Heavy, will require either local pickup or freight shipping. Dated 8D2 or April 2 1968. This item cannot ship through any conventional...

These Big Block motor mounts bolt to your engine block on the top side and to the motor mount (insulator) on the bottom side. These are very correct looking and fitting reproductions, much better than the $95 version you will find in most catalogs. Fits 1967-70 Mercury Cougar and Ford Mustang with 390 or 428CJ engines, will fit passenger side of 427 side oiler engine, driver side will work with modification. Original Ford part numbers C7ZZ-6046-A R.H., C7ZZ-6046-B L.H. 427 number for the left...

Used pair of right and left engine block plates for any 1967-69 Mercury Cougar or Ford Mustang with 390 engines, or 1968-70 428 cobra jet engines. These can be made to work on a GT-E 427 if the passenger side mount is modified for clearance.Replaces Ford part number C7ZZ-6046-A  and C7ZZ-6046-B.

New old stock Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a mercury  switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

After-market exact reproduction of the original Ford over the counter accessory. This handy little lamp can be mounted under the hood or the trunk lid. Features a gravity switch that turns the light on when the lid is raised and off when lowered.  Replaces Ford accessory part #: C2RZ-15A700-A.

Used engine lift hook or hoist bracket for all 1968-69 390 engines from any Mercury Cougar or Ford Mustang. Ambidextrous, fits either side as long as you use factory cast iron exhaust manifolds. X code 390-2V, S code 390-4V, and W code 427-4V engines. The factory used these hooks for installation of the engines into the cars on the assembly line. Nice detail to include for judged shows, many of these have been lost for various reasons. Sold individually, two needed per car, one on each side.We...

# 56350-S

Bolt that attaches engine mount to block. 4 bolts per engine, used on all v8 engines Mercury Cougar and Ford Mustang 1967-68. Sold individually.Ford number 304668-S2

New high temperature enamel for painting your block and underhood parts. So far, the best match has been the VHT brand, SP138 "Dark Ford Blue" paint (sometimes called "Ford Corporate Blue"). This enamel resists heat up to 550 degrees so it's a great paint to use on your engine. Dry to touch in 30 minutes and ready to handle in 1 hour. It's also resistant to all types of automotive fluid. Once you get this stuff on, it will not flake, crack or peel. ...

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Left hand bracket. Ford part number D0ZZ-6029-D. The original 1967 part number for this bracket was C7ZZ-6029-B.

Mount to the frame for supporting and mounting the FE 390, 427, and 428CJ engines. Also known as lower engine mounting brackets. For all 1967 - 1970 Cougars with 390 - 427 - 428 engines. Also includes 1967 with 289. Sold in sets. Includes one each: D0ZZ-6028-D & D0ZZ-6029-D engine frame brackets.

Several factory applications: 1967 - 1970 big block FE or 390, 427, or 428CJ. 1967 Cougar with 289 engines. Factory original part for all 1969 - 1970 Cougar convertibles with 351 engines. Right hand bracket. Ford part number D0ZZ-6028-D. The original 1968 part number for this bracket was C8ZZ-6028-B.

Reproduction pair of engine pedestals / frame brackets for the 67 - 70 big block V-8’s. Mounts to the frame for supporting and mounting the big block 390, 427 and 428 engines. Also known as lower engine mounting brackets. Sold as a pair.

Factory original part for all 1968 - 1970 Cougar hardtops (non-convertible) with 289, 302, and 351 engines. Left hand bracket. Ford part number D0ZZ-6029-C.