1967 Mercury Cougar

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-V stamped on the carburetor base, 1.14" venturi size 300 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

1967 289-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - 49 states. C7DF-L or AE stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note not for DSO 52 and DSO 53 California destined cars

1967 289-4V Autolite 4300 carburetor, 3 or 4 speed manual transmission - California DSO 52 and 53. C7DF-C or AG stamped on the carburetor base, 1.00" venturi size 470 cfm. Application for 3 and 4 speed manual transmissions. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engines and manual...

1967 289-4V Autolite 4300 carburetor, Automatic C4 transmission- 49 states. C7DF-M stamped on the carburetor base, 1.00" venturi size and 470 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. A code 289-4V engines with automatic transmissions. *Note - Not for DSO 52 and DSO 53 California destined cars. ...

1967 390-4V Holley 4150 carburetor, 3 or 4 speed manual transmission - California DSO 52 and 53. C70F-9510-C stamped on the carburetor air horn, Holley list #3795, 600 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. S code 390-4V and 390GT engines with manual transmissions. *Note - For use with California Thermactor smog equipped cars.

Rebuilt 1967 390-4V Holley 4150 carburetor, automatic C6 transmission- California DSO 52 and 53. C70F-9510-D stamped on the carburetor air horn, Holley list #3796, 600 cfm. Rebuilt carburetor with proper numbers. S code 390-4V or 390GT engines and automatic transmissions. *Note - For use with California Thermactor smog equipped cars.

Carter fuel pump, core grade for rebuilding purposes. This is a original Carter, button top fuel pump stamped 4194S. This is the early style with "CAR bure TER" and USA, has the 5/16" fuel nipple. Correct for 1967 Mercury Cougar with S code 390 engines and 1966-67 Ford or Mercury with S code 390-4V V-8 engines. The stampings on the housing edge is usually pretty light, sometimes the date stamp is not legible. These are so tough to find in the wild, that unless we have multiples and legible...

New Old Stock center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. Called an applique. Used only in 1968 on the one style XR7 hubcap. Not sure why it has a 1969 part number, error? Ford part number C9WY-1137-A.

Used chrome / black center cap for the 67 - 68 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers.Fits:1967 Mercury Cougar1968 Mercury Cougar

Used / refurbished center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. These are always faded, so we've "restored" a few with Sharpies, as shown in the picture. Believe it or not, it works pretty well and allows the shiny aluminum to show through the red. Be advised that the sharpie treatment doesn't hold up very well to rain and weather, so this is best for garaged...

Set of 4 Chrome center caps with Blue background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. The Magnum 500 wheel was not available on the Mercury line-up until 1974 and it came with a red center cap, star-burst pattern, made from plastic. This brand new to the market cap is a great alternative for the many folks wanting to run an attractive, era correct looking...

Set of 4 Chrome center caps with red background and chrome Mercury man logo. Better than original! These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these...

Chrome center cap with Red background and chrome Walking Cat logo for the Mercury Cougar. These are held on by a sturdy plate and two screws from the backside which is much better than the original clip-on type. There are other reproductions out there, but none are of this quality. When using center caps on Legendary wheels, you will need these adapter plates. *NOTE* When installing these die cast center caps, keep in mind over tightening will separate the backing from the chrome outer...

Used chrome / red center cap for the 1967 and 1968 Mercury Cougar and Ford Mustang Equipped with the Wire Spoke Hubcaps / Wheel Covers. Fits:1967 Mercury Cougar1968 Mercury Cougar

The only reason you would buy an original used unit is that you would want to match your existing original caps. The reproductions we carry are actually much better quality than the originals, as they will never fall off. Chrome center cap with black background and chrome Mercury man logo. Came from the factory on 1967 and 1968 Mercury Cougars with Styled Steel Wheels, but will work on any 67-70 with Styled Steel Wheels. Fits the following models with style steel wheels: 1967 Mercury...

Set of 4 reproduction chrome center caps with Blue background and chrome Mercury man logo. Better than original! New from Scott Drake. These quality center caps feature our high quality chrome bezels. Check out the details in our "Cougar" lens. Also available in red & black. *NOTE* Certain late model disc brake rotors and aftermarket rotors have a slight clearance issue with the dust cap and these center caps. **NOTE** When installing these die cast center caps, keep in mind over tightening...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

This one in, one out design was unique to the early 1967 Cougar for the headlights. Also found on vacuum controlled options like the 1967 Mustang Cougar tilt / tilt-away steering column. This is a good used unit that has been tested and found to hold vacuum well. This valve is located a few inches behind the carburetor.

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

Used distributor clamp and bolt, for any FE Engine: i.e. 352 / 360 / 390 / 410 / 427-4V / 428 / 428CJ / 428SCJ built from 1958-1976. Bolt may be used, or new from AMK Products. Ford part number B8A-12270-A.

Delicate clip that attaches to a nail-head stud attached to the firewall. Very functional and visible, rather hard to find in unbroken condition.

This clip looks just like the larger quarter extension moulding / trim moulding clip, but is smaller (as our comparison picture shows). One clip per side is used to attach the tail end (smaller end) of the moulding / trim to the extension. This unit is also almost exactly the same as the rear deck / trunk lid moulding / trim clip, but this quarter extension clip has a slightly shorter stud. Rarely will the clip you get look as good as the pictured here, usually the "finger" will be missing....

This clip looks just like the smaller rear deck / trunk lid moulding clip but is larger (as our comparison picture shows). One clip per side is used to attach the tail end (larger end) of the moulding to the extension. Rarely will the clip you get look as good as the pictured here, usually the "finger" will be missing. These clips are for the purest where originality is of the utmost importance. If originality is not an issue, you can get our excellent reproduction clip right here and...

Used clip to attach the rear deck / trunk lid moulding / trim on the Mercury Cougar that comes with a reproduction cadmium plated acorn nut. Seven of these clips were used to mount the anodized aluminum 1967-68 trunk lip moulding / trim to the trunk. These clip can also be found on some early 1969 Cougars with a stainless steel deck moulding / trim. This used clip is for our type "A" personality purists that insist on having the original part, even though nobody will ever see it. If ultimate...

Used plastic clip for the Mercury Cougar or Ford Mustang.

Clevis type attaching clip for attaching the accelerator throttle rod to the carburetor on all 1967 and 1968 Cougars. The correct installation is with the clip pushed on from the top, barbs down. This is the right handed style.Original Ford part number C2VY-9826-A

Set of seven used clips with reproduction stainless steel acorn nuts. These fit the best when using an original aluminum deck lid moulding on a 1967 or 68 Cougar. In 69-70 a stainless deck trim was used and the clip was all metal with no plastic coating. For more insight on this tricky trunk trim, check out our video below: ...

Pair or reproduction clips used to hold your transmission cooling lines together and keeps them from rattling.

New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A

D0ZZ-7528-C Equalizer bar or "Z" bar for FE big block engines with a manual transmission. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

C7ZZ-7515-D Manual transmission clutch fork - 3 and 4 speed, stick shift transmissions. Fork measures 12 inches long. Cougar 1967 through 2-15-1968. 390-4V engines only, XR7, XR7-G. Mustang 1967 through 2-15-1968. 390-4V only, GT. Mustang 1967. K code 289 HiPo 4 speed only. GT

Used clutch spring bracket that attaches to the brake / clutch hanging bracket. All 1967-68 Mercury Cougar and Ford Mustang with manual transmissions. Replaces Ford Part #: C7ZZ-7535-B.

Tall version 1" thick and can be used with performance springs to bring the car to a stock ride height. Sold as a Pair. Replaces Ford Part #: C4DZ-5415-A.

Hot idle compensator valve assembly for many Ford engines with PCV, starting in 1964 through early 1968. Typically found on 1964-66 Ford 260-2V, and 289-2 engines with air conditioning. 1967-68 289-2V, 302-2V and some 390 engines all with air conditioning and PCV or closed emissions. The Ford assembly manual indicates that the Hot Idle Compensator Valve 'T' Assembly, was installed by removing 3/4 inches of the PCV hose, 2-1/4 inches (on center of the PCV valve). See picture for clarification....

This is an original NOS hot idle compensator for Mercury Cougar or Ford Mustang models with V-8 engine and factory A/C. It is installed in the middle of the hose that connects the PCV valve to the rear of the carburetor spacer. It opens when it reaches a certain temperature which makes the engine run faster when at idle and the A/C is on thereby making the engine run more efficiently. This is an original Ford part that came on air conditioned models from the factory. It was manufactured by...

Ford sold service replacement taillights as a complete unit that included the backing, chrome and lens, just the lens or just the chrome. This listing is for one complete taillight unit as shown. Sold individually, two required per car. Ford part number C7WB-13440-A *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential...

This complete four part kit is correct for any 1967-68 small block 289 or 302, and 351 Windsor Mercury Cougar or Ford anything 1967, 1968 and 1969. Used aluminum pump mounting bracket, front adjusting bracket with large hole, pivot stud, and nut.If you do not have a air conditioning you will need a spacer in place of the round spacer shown. If you have the 351 Windsor without A/C, you will need a the rectangular spacer which is sold separately.

Complete roof cut that includes the rear window opening and package tray. These roofs may or may not have the holes drilled for a vinyl top. If you have doubts of whether or not you need a roof with or without a rear window, we suggest that you remove your rear glass and peel back your vinyl roof and inspect the lower channel where the rear windshield rests and the section of steel covered by the vinyl material. 1967 and 1968 Mercury Cougar roofs are the same, the only difference being the...

This black complete wheel is a rare find. This would be considered a B+ because it is not separating or cracking badly on the rim. The cracks shown on the 3 spokes would be much easier to fix than cracks on the rim. Notice how clean the chrome is on the horn bar. Check out this video

This unit is for Mercury Cougars and Ford Mustangs, is pre-assembled, and includes the drier and all brackets.

Used metal Connector for use on any 1967-68 Mercury Cougar or Ford Mustang with speed control. This connector goes between the Servo and Bell Crank. Connector only, hitch pin and clips not included. Complete Ford part unknown, but it has a basic part number 9D763.

Differs from the original lens in that it is all white. The original was painted white on one half and left clear on the other.

This listing is for a 3 bolt type upper ball joint, NOS, original Ford Service replacement upper control arm assembly. We have a very hard time keeping these in stock but we keep the listing up as it is good for comparison sake when considering the differences between reproduction and OEM. Keep in mind, service replacement parts often differ slightly from what actually came on the car. Over the years tooling is often replaced or modified and suppliers of things like fasteners often change....

Used Grade A Standard Convenience Panel for the 1967 Mercury Cougar 

C6OE-D and C7AE-F marked fans. Applications: 1. 1968 C code 289-2V engine without air conditioning or heavy duty, or 'extra cooling' option (small radiator). 2. 1969 Boss 302 Eliminator and Mustang. Mustang owners, this 4 blade fan with the part number C6OE-D and (C7AE-F for 1967 and later), is also correct for those K code 289 HiPo engines in both 1966 and 1967. Fan description - 4 blades and 17-1/8 inches in diameter. Ford master part number C6OZ-8600-D. Check out this interesting video...

C5AE-B This is the early 1967 production cooling fan, used up until 11/14/1966 on 289 engine applications. This does not include those cars with factory, or "integral" air conditioning. Fan description - 5 blades and 17 inches in diameter. Ford master part number C5AZ-8600-A. *Note - Excludes integral air conditioning. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

C6OE-G Clutch style 7 blade cooling fan for all 1967 Cougars with 289 engines with factory installed air conditioning. Additionally, 1968 302 engines with factory air conditioning (Cougar and Shelby GT-350 only). Fan description - 7 blades and 17-1/2 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C4OZ-8600-D. Original fan drive clutch cast number for this application is C7ZE-B. NOTE! If you have the fan shown here and would like to upgrade to our FE / Big...

C6OE-F Clutch style cooling fan found on all 1967 S code 390 engines, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. Ford master part number C6OZ-8600-F. Original fan drive clutch cast number for this application is C7ZE-A. If you have one of these fans and would like to trade it straight across for one of our C8OE-B or C9ZE-E fans please contact us! Check out this interesting video where they test the...