1967 Mercury Cougar

A/C and heater control bezel or face plate. Grade A- used condition, standard pebble grain trim. Check back often, this type and grade of part is seldom in stock very long.Bezel only, no levers or switch.Ford part # C7ZA-19C705.

[No Description Provided]

New intake manifold that has never been used, but it's missing the packaging, so we're calling it an "out of box special". Port size is for the 2V cylinder heads. Perfect for adding a 4 barrel carburetor to a stock 351 Cleveland 2V engine.

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Used driver side (left hand) rear armrest for the Mercury Cougar that is in grade A condition. Grade "A" armrests are not pulling away from their backing and have no splits, cigarette burns or other obvious defects. They may need to be painted with vinyl paint, especially since we can almost guarantee we will not have both sides in your color in stock. Please indicate in the notes which color you would prefer, we will do our best to accommodate you. *NOTE* If you have a standard or decor 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like this one often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like this one often need to be repainted as they show discoloration more often than the darker colors. The armrest shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967 -...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used armrest with no cracks or cigarette burns. The lighter colors like aqua and white often need to be repainted as they show discoloration more often than the darker colors. The armrests shown were all taken from 1969- 1970 Decor and XR7 Cougars. Standard model Cougars did not have rear armrests in 1969 - 1970 Coupes. Unlike the 1967 - 1968 rear armrests the 1969 - 1970 rear armrests are far less prone to pulling away from their backing. These armrests are also a direct fit to your 1967...

Good used solid panel with all parts removed. Panel measures 19.5" x 39". Whereas at first glance these may all look the same, the contour of the roof changes with the body style changes. Call us for price and availability on panels with varying degrees of repairable rust.

Get the all 5 Engine, Body, Chassis, Interior, and Electrical Assembly manuals for the price of 4. These are a must have for anyone doing their own repairs. Even if you pay others to do your repairs you should always have these in hand when you hand the keys to your mechanic as it will save whoever does the work hours. These are the blueprints the line workers used to build these cars in the day. Every nut bolt and clip is shown. The exploded diagrams make it easy to know what goes where. You...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange without fill plug in housing. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long. Complete rear end housing - drum to drum, with...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Rear axle assembly - Housing, Axles, brake backing plates, and third member. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. 1967 early 9 inch rear end housings had the carry over fill plug in the steel housing as seen from the back of the car. As removed from West Coast Cougar organ donor car. We recommend a bearing...

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Rear axle assembly - Housing, Axles, brake backing plates, and third member. 1967 late 9 inch rear end housings without fill plug in the steel...

Original New Old Stock NOS reverse light lenses. Sold as a pair, includes screws!Ford Part number C5ZZ-15514-A.

Used backup / reverse light for the driver side (left hand) of the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Casting number as seen on the back side reads C7ZB-15A509-A. Replaces Ford part # C7ZZ-15512.

Used backup / reverse light for the passenger side (right hand) of the the Mercury Cougar and Ford Mustang. Lens, gasket, and bulb sold separately, but we do have a kit available. These used lights will often have a minimal amount of pitting on the inside close up to the lens. Perfect inexpensive replacement item for those wanting to keep their car all original and match the overall patina of their low mile car. Casting number as seen on the back side reads C7ZB-15515-A.Replaces Ford part #...

Correct for closed emission system Cougars sold only in California. Air cleaner base for both the 289-2V and 289-4V engines. About 17.25" inches in diameter. California emissions with the metal elbow for hose connection to the oil filler cap.

Factory air cleaner base the all S code 1967 Mercury Cougar non-GT or the 6.5 Liter option, 1967 Mustang 390-4V without the GT option, and 1967 Ford Thunderbird with Z code 390-4V or Q code 428-4V engines. California emissions version which has the closed emissions. Note the elbow on the side which attaches with a hose to the oil fill cap.This is the one everyone uses to make a correct 1969-70 428 Cobra Jet ram air or 1967 GT air cleaner base . This basic bowl design was used by the Ford...

Good used tray that is not currently reproduced. Most people prefer the group 24 battery but for those that want to keep it very original, this is getting to be a hard to find part with no rot (will show pitting). Many that are not rotted have been cut to accept a group 24.

Good used group 24 tray for 1967 Mercury Cougar or Ford Mustang. Assembly line installed group 24 battery tray with holes for tilt vacuum canister. For those that want to keep it very original, this version is not reproduced. This is getting to be a hard to find part with no rot (will show pitting).

Used upper steering column bearing for your 67 - 73 Cougar or Mustang. One required per car. Fixed Columns only use the upper bearing, while the tilt columns used an upper and lower. The used lower bearing can be found here. Outside diameter: 1 3/16 " * - may not fit some 67 Mustang applications with a fixed column as these used Ford part # C4OZ-3517-A, which is the same part used in the Fairlanes/Comets with a fixed column. To our knowledge this bearing is not currently reproduced. *NOTE* For...

Used Bell Crank from the Servo Assembly on any 1967-68 Mercury Cougar or Ford Mustang with speed control. Attaches to the Connector, via a Shaft, and Trunnion is attached. Ford part number C7ZZ-9B713-A.

C5OP-7976-A Aluminum bell housing, sometimes called a converter housing in the Ford shop manual. 1967 - 1968 Mercury Cougar with any 289 or 302 engine and automatic C4 transmission, code W on your door tag. 1967 - 1972 Ford Mustang with 250, 289, or 302 engine and automatic C4 transmission, code W on your door data plate. Fits the 157 tooth flex plates. There was a 164 tooth flex plate that came later. NOTE * Grade B bell housing will have a chip or heavy scarring on the bottom, see photo...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

Manual transmissions, include both 3 and 4 speed Top Loader transmissions. Ford part number C6OZ-6392-B. The latest research shows that the casting number C60A-6394-B bellhousing may have been for 1966-68 Cougar, Mustang, Fairlanes and Comets with an 11 inch clutch disc.  Shipped bare, no hardware or clutch fork.

Emergency flasher bezel for the side of the tilt steering column. Another hard to find, fragile, plastic part. Subject to availability. Paint to match your interior.

Driver side headlight door. New Old Stock.If you happen to be missing this door (bezel) you are doing damage to your grille each time you open and close the covers (eyelids). This acts as more than just a finish piece, it adds rigidity to your grille which is made from a rather soft metal. This listing is for the driver side headlight door. The backside is marked TOP R.H. / L.H. and carries and Ford casting number of C7WB-13064 for the driver side and C7WB-13064 for the driver side. The four...

Used radio bezel Grade A used. For use on 1967-68 Mercury Cougar or Ford Mustang cars without console. 2-3 different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

Used radio bezel that will show minor pitting and will most likely need the black area repainted. For use on cars with no console. Two different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

This is an uncut, pit free, crack free radio bezel. She is mint, no excuses! Keep in mind we have bezels that have been altered for an after market radio for much less money.Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a storage compartment. The slide up doors are different between the 2 years due to the handle being different. The 67-68 Mustang console also had this slide up door. This slide up door works like the...

This used bezel is covered almost entirely by the face pad with clock. Only the small area around the radio actually shows once installed. This early bezel has the upper support, the later version is open. Keep in mind we have bezels that have been altered for an after market radio for substantially less money.Ford casting number C7WB-6504567-B  68102-171Need some help getting that old unit out? Here’s some guidance from our buddy Randy Goodling.All 67-68 standard consoles had a...

Very rare find... A restored bezel will look fine but will never retain the sharp edges and matte black finish like this new in the box original Ford part.

They made three different versions of this plate for non console Mercury Cougars equipped with a manual three or four speed transmission. This part was not found on Mustangs as the Cougar often used a little "fancier" detail items in and out. Check out our video on rebuilding your shifter below: ...

Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. We consider the one remaining a B+ grade, due to pits in the chrome. This version is the one held down with 2 screws. Part number C7WB-7262-C is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-B, &...

Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. We consider the one remaining a B grade, due to pits in the chrome. This version is the one held down with 4 screws. Part number C7WB-7262-A is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-B, &...

This is for the person who does not want to modify the off-shore Mustang reproduction wheel lip mouldings we sell but do not have good cores for exchange for our premium set of restored wheel lips. Each one of these wheel lips will show some imperfections, mostly found on the inside where the wheel lip fastens to the wheel arch. The blems most commonly found on our less than perfect wheel lip mouldings may include multiple extra little holes drilled for mud flaps, "speckles" in the finish from...

Good used working original heater blower motor for 67 - 68 Mercury Cougar and Ford Mustang.  The reproduction off-shore units may or may not prove to be as good of value as these good used original FoMoCo motors.  Keep in mind our used units carry a one year warranty and the new off-shore motors only have a 30 day warranty.  Also know that the mounting plate is included for free just by asking on the used motors. We never use the reproductions here at WCCC.  This unit...

C5ZZ-7610962-A Ford description of this plate is "Plate - Front floor lower cross member". All 1967-73 Cougar convertibles and all 1965-73 Ford Mustang convertibles use this plate. Bolts into place with 6 hex bolts 3/8-16 x 1-1/8" with washers. These were painted satin black from the factory. As you look at our picture below you will see the repro is about half the thickness. The repro is different in every detail but will work. We also have used plates with minor damage at a reduced cost.

373460-S Factory original used bolt used to fasten the guide to the door (2) Reproduction version from AMK - https://secure.cougarpartscata...

Front retractor bolt, used in conjunction with two rubber spacer / washers and one washer. The two rubber washers go on either side of the re-tractor mounting hole and the metal washer is against the inner rocker.

Set of new bolts for attaching the floor shift bucket to the hump in the floor board, 1/4-20 bolts with washer head and 3/8 inch hex head. Sold as a set of 4 bolts. Fits all 1967 - 1973 Mercury Cougar and Ford Mustangs, and likely all of other floor shift Ford products from this time period. Check out our video on rebuilding your shifter below: ...

Application - 1967 Mercury Cougar and Ford Mustang with 390 engines.  Might be two versions, this one would be the mid or late version. There are references that this bracket was also used on 289 engines with air conditioning, but that may not be consistent through out the year, if it all. Maybe early 1967 cars with A/C. Ford part number stamped C7AE-9B453-A.