Electrical & Lighting

NOS Speed or cruise control switch, for factory installed cruise control. Very rare option on a Cougar or Mustang, also fits Thunderbird and Lincoln.  The 1968 Electrical manual shows a Lincoln part number of C7VA-9D752-G. Service replacement part number is D1VY-13305A. Would need to remove the white tilt bale collar prior to use.

NOS turn signal wand. One year only unique design. The superseded service replacement part # D1VY-13305A Is what most cars have installed in their 1967. Very few of these exist today as they were only made one year. This is the early 1967 turn signal stalk with cruise or speed control. Likely manufactured by Curtiss-Wright.Ford Part number C7ZZ-13305-B2Statistics:1967 Mustang - 55 total cars with speed control option. 17 coupes, 20 fastbacks, 18 convertibles.1967 Mercury Cougars -...

Reproduction Speed or cruise control switch, for factory installed cruise control. Very rare option on a 67-69 Cougar or Mustang, also fits Thunderbird, Lincoln, Marquis. Keep in mind that these new levers will not come with the plastic plug at the end of the harness, you will need to use your old one, or you can splice as shown in the included installation sheet. As you know, these levers were made from plastic in the sixties and seventies. This new reproduction is machined from billet...

Used turn signal wand. One year only unique design. The superseded service replacement part # D1VY-13305A Is what most cars have installed in their 1967. Very few of these exist today as they were only made one year. This is the early 1967 turn signal stalk with cruise or speed control. Likely manufactured by Curtiss-Wright.Ford Part number C7ZZ-13305-B2Statistics:1967 Mustang - 55 total cars with speed control option. 17 coupes, 20 fastbacks, 18 convertibles.1967 Mercury...

This is a cost saving unit when you have a functioning system that just runs slow. The original motor will often make noise and fail to turn in cold weather. This solid state unit will cure that and will sequence your lights fast and silently with no cleaning or adjusting of the points like your original mechanical unit.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is...

*NOTE* According to Phil Parcels of the National Cougar Data Base Project, the approximate cut off VIN for determining EARLY or LATE 67 is: 7F91C547891 Cars with a VIN number higher than this would use the late sequential unit. Cars with a VIN number lower than this would use the early sequential unit. NOTE! If you are unsure whether your Cougar is a late or early model then order this early unit as it works on both. This solid state turn signal sequential kit eliminates all the...

*NOTE* According to Phil Parcels of the National Cougar Data Base Project, the approximate cut off VIN for determining EARLY or LATE 67 is: 7F91C547891 Cars with a VIN number higher than this would use the late sequential unit. Cars with a VIN number lower than this would use the early sequential unit. This solid state turn signal sequential kit eliminates all the mechanical motor-driven sequencers and relays used in the trunks of the 1967 Cougars built after 1-2-67. One system module...

Used late grade "B" under dash wire harnesses. There are two versions of this harness, and early and a late version. This late version is for Cougars built after to 1/3/1967, the early version is for Cats built prior to. In January of 1967 Mercury eliminated the stop lamp relay and integrated it into the sequential main turn signal relay, known as the K8-K9 relay. The early and late versions will not interchange with each other. All our harnesses will be inspected, professionally repaired,...

Here is a real treat! This grade "A" harness is a very hard to find harness as the XR7 was not even introduced until mid-model year of 1967. The 67 harness has several differences from the 68 which keeps it from being able to interchange with any other year or model. We also have this harness in B grade condition, tested with some obvious repairs, but all in working condition. Harness can carry a tag marked C7WB-14401-G, -L, -N.*NOTE* If you send us your old used under dash harness, you will...

Used grade "B" harness with one or two professional repairs. This is a very hard to find wiring harness as the XR7 was not even introduced until mid-model year of 1967. The 67 main under dash wire harness has several differences from the 68 which keeps it from being able to interchange with any other year or model. Harness can carry a tag marked C7WB-14401-G, C7WB-14401-L, C7WB-14401-N.*NOTE* If you send us your old used under dash harness, you will receive an in store credit of up to $100....

Used standard grade "A" under hood main wiring harness located in the engine compartment. This harness has plugs for the headlights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, tested, and ready to install. Grade "A" harnesses are rare uncut beauties. 1967 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7 model Cougar with Ammeter. Ford part # C7WY-14290-J.

Used standard grade "B" under hood main wiring harness located in the engine compartment. This harness has plugs for the headlights, voltage regulator, starter solenoid, windshield washer pump, and horns. All electrical harnesses are inspected, professionally repaired, tested, and ready to install. Grade "B" harnesses may have one or two repairs where the grade "A" harnesses will be rare uncut beauties. 1967 Mercury Cougar Standard models only with AMP warning light. Not compatible with XR7...

Reproduction head light wiring harness for the Mercury Cougar. These are concours quality EXACT reproductions! Every wire, every stripe and connection is exact. We have many good used wiring looms in stock for front, under dash and rear, give us a ring or email for details. Our reproduction harnesses are made by seasoned craftsmen who use only the original Ford drawings and EXACT materials. Many of the connectors are NOS.Replaces Ford part # C7WY-14290-J.

Reproduction under hood wiring harness for the Mercury Cougar. These are concours quality EXACT reproductions! Every wire, every stripe and connection is exact. We have many good used wiring looms in stock for front, under dash and rear, give us a ring or email for details. Our reproduction harnesses are made by seasoned craftsmen who use only the original Ford drawings and EXACT materials. Many of the connectors are NOS.Replaces Ford part # C7WY-14290-H.

Used headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the common version with the separate ground wire where very early 1967 Cougars and Thunderbirds did not have that separate ground wire. We won't always have these used units in working condition in inventory. We also sell a rebuilt solenoid here. Ford part # C7SZ-13A161-A. *NOTE* This item will not ship until a rebuildable...

New Old Stock headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the early solenoid valve without ground wire. Early 1967 Cougars and Thunderbirds did not have that separate ground wire. Has the proper opaque white color for the vacuum switch plastic.  Ford part # C7SZ-13A161-A.

Used headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the common version with the separate ground wire where very early 1967 Cougars and Thunderbirds did not have that separate ground wire. We won't always have these used units in working condition in inventory. We also sell a rebuilt solenoid here. Ford part # C7SZ-13A161-A. *NOTE* This item will not ship until a rebuildable...

This is the cover only. Great for those wanting to use a reliable modern solid state regulator but look concours. Comes with rivets.Replaces Ford part number C5TF-10316-A (cover only)

Is your 67 - 68 Cougar or Mustang having some electrical problems? Are your dash gauges not working like they used to? If so, you should consider a new voltage regulator. Features & Benefits: - Improved Design for Better Reliability and Accuracy in Heat, Humidity and More- Solid State Electronic Circuitry and Variable Controls- Made of Premium Materials for Durability- Mounts Behind Your Dash GaugesReproduction Constant Voltage Regulator features an improved design that makes it more reliable...

Electronic voltage regulator for use on any 1967-73 Mercury Cougar or Ford Mustang or Ford. Same foot print as originals, cover can be swapped.

Affixes to the back side of your cluster. Far superior to the current reproduction units that are available.Check out the video below on our new gauge tester: ...

New reproduction instrument panel voltage regulator or IVR for all 1967-68 Mercury Cougar and Ford Mustang. Additionally fits 1967-68 Ford full size, 1966-68 Torino,CycloneMounts to the rear of the instrument clusters, voltage regulator for dash gauges power. Ford part number C6DZ-10804-A.Check out the video below on our new gauge tester: ...

Features the proper cover and original logos. I A S F stamped on cover. Replaces Ford Part #: C5TF-10316-A. These new voltage regulators are improved and more reliable than the units we've sold previously. NOTE: There were two versions of this regulator, the black with yellow writing was 55 amps, and the black with silver writing was 44 amps. We do not have a supplier for the black and silver version at the moment.

Reproduction Dash to Engine Gauge Feed with push-on Post Oil Sender for the 1967 and 1968 Mercury Cougar with the 289 or 302. Red / Green stripe wire = Coil White / Red stripe wire  = Temp Red / White stripe wire = Oil lamp * Note - Verify your oil pressure switch has the connector to accept the push on boot plug. Replaces Ford Part #: C6DZ-14289-BCheck out the video below on our new gauge tester: ...

Reproduction Dash to Engine Gauge Feed with Tach and Slide-on clip Oil Sender for the 1967 and 1968 Mercury Cougar with the 289 or 302. * Note - Check the style of oil pressure connector on your engine. Replaces Ford Part #: C7DZ-14289-BCheck out the video below on our new gauge tester: ...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.Replaces Ford Part #: C9ZB-19A885-B.

Reproduction console feed harness for the 67 - 68 Cougar or Mustang. This OEM direct fit wiring harness supplies power from the under dash harness to the console harness.

Used fuse block / box without wiring for the under dash harness on the 1967 Mercury Cougar. Good for standard or XR7.

Reproduction console wiring harness for 1967-68 Standard Cougar any all Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Replaces Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

New console wiring harness for 1967-68 Standard Cougar any all 1967-68 Ford Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

Console wiring harness for 1967-68 Standard Cougar any all Mustang. This harness is for the light in the roll up garage door compartment and the rear console lights. There is a jumper wiring harness also available, that connects to the main under dash harness. See related items. Ford part number C7ZB-13B711-A. *Note - Not for Mercury Cougar XR7 models.

This the light connector harness for the dash convenience panel that connects to the door harness (door ajar) and low fuel harness. Fits both 1967 and 1968 Mercury Cougar and Ford Mustang. Has low fuel lead for Cougar on driver side, plug for low fuel on passenger side for Mustang. One plug is unused, depending upon application. This is a rare option, indicator lights would be installed in the center section of the dash panel. Unless, air conditioning was installed. If the car...

This the main under dash harness for the convenience panel that connects to the door harness (door ajar) and low fuel harness. Fits 1967 Mercury Cougar and Ford Mustang. Has low fuel lead for Cougar on driver side, plug for low fuel on passenger side for Mustang. One plug is unused, depending upon application. This is a rare option, indicator lights would be installed in the center section of the dash panel. Unless, air conditioning was installed. If the car had factory A/C and the...

Wiring harness for the low fuel sending units on 1967 Mercury Cougar XR7 and standard models with low fuel warning light. The Safety Convenience Option included a low fuel warning light. This harness has two wires which attach to the three prongs on the 1967 C7ZF-9275-D low fuel sending units.1967 and 1968 will interchange, 1967 has a plastic shielding on the end of the wire loom that is under the car. 1968 version does not have this shielding. We suspect that the Ford part number is...

Used lower wiring harness for the overhead console on the 67 Cougar XR7. Sometimes known as the Convenience Group Harness. This harness runs down the C pillar, under the door scuff plates and exits on the passenger side under the dash. That's where it connects to the under dash wiring harness. The upper harness runs from the overhead console, under the headliner and back to the C pillar where it connects to this lower harness. You can get the upper harness here. Ford Part Number C7WB-10C877-C ...

Used upper wiring harness for the overhead console on the 67 - 68 Cougar XR7. Sometimes known as the Convenience Group Harness. This harness runs under the headliner from the overhead console back to the C pillar, where it connects to the lower harness. You can get the lower harness here. Ford Part Number C7WB-10C877-F

Used grade A standard 14405 harness is inspected, professionally repaired, tested, and ready to install. This harness connects to the main 14401 under dash harness at the passenger side door jamb, and runs through to the trunk. It connects to the sequential unit and the fuel sending unit.These grade "A" harnesses will be uncut and unburnt. This is for those of you who demand excellent original parts for your Cougar.

Used grade B standard 14405 harness is inspected, professionally repaired, tested, and ready to install. This harness connects to the main 14401 under dash harness at the passenger side door jamb, and runs through to the trunk. It connects to the sequential unit and the fuel sending unit. Grade "B" harnesses may have one or two repairs where the grade "A" harnesses will be rare uncut and unburnt beauties.

Used grade A standard 14405 harness is inspected, professionally repaired, tested, and ready to install. This harness connects to the main 14401 under dash harness at the passenger side door jamb, and runs through to the trunk. It connects to the sequential unit and the fuel sending unit.  NOTE: The 1967 harness does not include the overhead harness wiring. These grade "A" harnesses will be uncut and unburnt. This is for those of you who demand excellent original parts for your Cougar. ...

Used XR7 14405 harness is inspected, professionally repaired (if needed), tested, and ready to install. This harness connects to the main 14401 under dash harness at the passenger side door jamb, and runs through to the trunk. It connects to the sequential unit and the fuel sending unit, and also connects to the overhead console. Ford part number C8W8-14405-F

Used seat belt warning light / harness for the 1967 Standard Mercury Cougar. Includes original used light bulb and fuse.  Ford part number 10B925

Quality wiring reproduction for Perfect Circle brand of speed controls as found on most 1967-1971 Ford - Mercury - Lincoln automobiles. Main harness with Ford part number 9A840, can be used on a variety of model and years. Harness connects the servo, has grommet for firewall, and connectors under the dash. Jumper wire to the brake pedal.

Factory used and tested under dash wiring harness for all 1968 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This harness plugs into the speaker plug of the radio, and connects the kick panel speakers in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door wiring harness that has the speaker plug for the door mounted speakers in 1969-70 cars. White speaker wire goes to the passenger side speaker, and the orange colored wire...

This wiring harness has an included lamp socket that plugs into your instrument cluster just below your right turn signal light.This 1967 harness attaches to the ignition switch, and the seat belt reminder relay (sold separately). Tested harness includes 1895 bulb, 7-1/2 amp fuse.

Power wire that connects the PRNDL or shift indicator illumination lamp assembly, and the main under dash wiring harness on all 1967 Standard Cougars and Mustangs. All electrical harnesses are inspected, professionally repaired (when needed), tested, and ready to install. Harness marked C7ZZ-15A808-A. Has red colored bullet plug to main harness, and black plug to PRNDL wiring. Fits 67 CougarFits 67 Mustang

Used wiring pigtail that runs from the under hood harness at the kick panel to the starter solenoid / horn / voltage regulator on the 67 - 68 Cougar.

Emergency or parking brake indicator lamp and wiring harness. Tested and working red indicator light which was found optionally on any 1967 Mercury Cougar standard model 65A or 65C. The 1967 parking brake light kit gets its power from the ignition switch. Ford part number C7WB-10A841-A.