Electrical & Lighting

These courtesy light brackets are located on the very outer right and left under the dash. Typically this bracket is found on the passenger side of 1967-68 Mercury Cougar and Ford Mustang without air conditioning. This is the long style bracket. There is also a short style for both the driver and passenger side courtesy light. If you have factory air conditioning you would want the short bracket that doesn't come into contact with the A/C plenum.Replaces Ford part number C7ZB-13763-A.Fits:1967...

Used bracket for mounting the various relays found on 1967 Mercury Cougars, both standard and XR7 models. This bracket mounts under the dash off of another bracket (see 1967 Cougar Electrical Assembly Manual page 15).*Note - 1968 used a different bracket.Replaces Ford part number C7WB-14A301-B.

Used windshield wiper mounting bracket for any 1967-68 Mercury Cougar or Ford Mustang. Part of the wiper motor assembly in the Master Parts Catalog, so no Ford number found.

Warning lens indicating "BRAKES", attaches to the tachometer on any 1967-68 Mercury Cougar XR7. This is a red back lit lens, it tapes onto the back side of the tachometer bezel. Ford part number 10A936

Correct Backup Light Bulb for the 1967 - 1968 Mercury Cougar. Owners Manual and shop manual incorrectly state the backup light bulb to be the 1156.

Brand new 1157 (dual-filament) exterior stop lamp / turn signal light bulb for the Mercury Cougar or any vehicle equipped with 1157 bulbs. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. For even brighter...

The 67 -73 Cougar uses the 1157A (Amber) bulb for the turn signals.  This bulb will also fit other applications that require an 1157A or 1157NA bulb. Replaces bulb #: 1157A or 1157NA

Replacement lamp for the speedometer, heater controls, ashtray, automatic shift indicator, low fuel, seat belt reminder, or emergency flasher warning lights on the visual check panel.

This bulb fits several applications including the door panel courtesy lights in the 1967 - 1968.

New 1891 bulb for the 1967-68 XR7 overhead console. This bulb will also fit the 67 - 68 rear console light. You can find the LED version of this bulb here.

New 1895 bulb for the instrument clusters. *Note - The table and the owners manuals are wrong for the Visual Check Panel bulbs, Ford literature calls out a 1895 bulb, when in fact the correct bulb is 1891.

Reproduction 631 Glove / Luggage Compartment / Under Dash Courtesy / Trunk Light Bulb for the 1967 - 1973 Mercury Cougar

Bushing that goes to the inside of the brake booster pushrod. This is the early version of this part that is made of plastic, a later version was introduced in 1969 which was made of nylon and is/was more durable.Replaces Ford Part number C9AZ-2474-A

Reproduction bushing for the master cylinder push rod where the switch and brake pedal converge. Two required per car and the bushings are sold separately.Ford part number C5DZ-2B129-B

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...

Used on 1967 Mercury Cougar and Ford Mustang for the air conditioning, located under the dash to the back of the ignition switch. 25 amp circuit breaker, identified in the Ford MPC as part number C5AB-14A065-F or C5AZ-14526-C. It is 1.25" x 0.80". Box is marked FASCO Type 4110. 25AMP 12V. Attached mounting tab is included.These are tested and guaranteed to work.

Used in 1967 Mercury Cougars for the stop lamp switch, located under the dash on a panel next to the fuse block.15amp circuit breaker, not clearly identifiable in the Ford MPC. It is 1.07" x 0.40". Box is marked 15AMP 12V, and made in the U.S.A. Integrated mounting tab for this application. The MPC shows this circuit breaker was also used on 1965-66 Continental convertible and 1965 Thunderbird convertible. These are tested and guaranteed to work.*NOTE* Need help diagnosing a Cougar turn signal...

Used on 1967-68 Mercury Cougar and Lincoln Continental for the tail lamps or running lights in the rear, located in the trunk drivers side upper rear corner. Also used on 1967 Mercury Cougar and Ford Thunderbird for the headlight vacuum solenoids, mounts on panel under the dash board for that application. This 5 amp circuit breaker cycles the rear taillights on and off and is not clearly identifiable in the Ford MPC. It is 1.25" x 0.80". Box is marked FASCO Type 4110. 5AMP 12V. Integrated...

Reproduction batter bracket or clamp for battery installation. "L" bracket attaches to the battery apron and steps down for the battery hold down clamp. Not sure which cars got this, but likely was for the larger sized battery. Fits 1967-68 Cougar and Mustang including Shelby Mustang. USA made preproduction part. 

Stamped steel construction with black vinyl coating like the original to prevent corrosion. Please note that vinyl coating will almost always crack along edges shortly after installation, just like the originals did... This is the same exact hold down you will see listed elsewhere its just that we feel you should know what you are getting up front so you will not be surprised. Replaces Ford part #: C5AZ-10718-A.

Includes battery clamp and bolts required to mount battery on tray. Please note that vinyl coating will almost always crack along edges shortly after installation.

New clip for holding a single wire. Often times this clip is used for the trunk light. Also seen under the dash panel on select years. Most likely other locations too from the factory. Panel hole size is 1/4 inch. From the factory one clip was used per car for the trunk light. Sold individually.  Replaces Ford part number 382929-S.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Vinyl dipped. Clip is used to hold wiring away from hot engine. Also found on trunk floor.

This unit has had the original movement replaced with a quartz movement. It has been meticulously rebuilt by the best in the business and features a new, crystal clear lens. $150 credit when you return your clean rebuildable core with a copy of your invoice. Quartz movement clocks have second hands that click around, original clocks had a constant sweep of the second hand. Check out the video below on our new gauge tester: ...

This is a NOS clock. The face is brilliant, it has never been mounted and is guaranteed to work good. It does have a tiny crack that is mostly hidden by the center knob which is very common for these original lenses.  This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

C7WY-15000-A 1967 - 1968 Standard Cougar body code 65A or 65C, found optionally in the small center pod of the instrument cluster. Used clocks generally do not work after 40 years and unfortunately these do not include the clock knob as folks often do not put them back on after removing them from the cluster. These are considered cores. We also offer rebuilt clocks with modern quartz movements and those will include the knob. Check out the videos below on our new gauge tester and the "Cougar...

NOS 1967 - 1968 Standard Cougar body code 65A or 65C, found optionally in the small center pod of the instrument cluster. Ford part number C7WY-15000-A Check out the video below on our new gauge tester: ...

1967 - 1968 Standard Cougar body code 65A or 65C, found optionally in the small center pod of the instrument cluster. This clock has had the original mechanical movement replaced with a new quartz movement by the best auto clock restorer around. Some of these standard clock faces have discoloration so if your face is mint you will want to send the core to us prior to us sending one out to you so as to insure like quality. You should get many, many years of trouble free accurate use out of this...

Used clock for the center console equipped Mercury Cougar XR7. Most used clocks typically do not work after 40+ years and you can also expect that the lens will have some cracks. However, we offer a nice reproduction lens or restored clocks with a modern quartz movement or NOS movement.Ford part # C7WY-15000-B.Check out the video below on our new gauge tester: This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we...

[No Description Provided]

Prepare to be disappointed... This is a reproduction 1967 - 1968 Ford Mustang clock knob and set screw (replaces Ford part # C7ZZ-15032-A) that can be cut down to work on your 67-68 standard Mercury Cougar (barely). The pictures below will guide you on this "adequate at best" solution for those of you missing this hard to find knob and set screw.Click on images to enlarge. The above picture is a good used original Cougar knob mounted on a 68 clock.  We do not have these original Cougar...

Used 1969 351W coil mounting bracket. This version of the bracket is specific on the 351W and allows extra room for the oil dipstick. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. Listed in the...

Reproduction coil mounting bracket. The manufacturer claims it fits all cars 1967-73. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to the front of one of the cylinder heads. To our knowledge this is the only reproduction style on the...

Used coil mounting bracket. This is the Big Block V-8 version starting 1967-69. Found on 390 and 428CJ cars. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. This version is for big block V-8's, and has an additional 'C" channel bracket on the bottom, later versions had an removed thel reinforcing 'C' channel on the bottom. Later version...

Used coil mounting bracket. This version of the bracket is probably the most common. Typically this version was used on small block V-8's in 1967-68. This version has the 'rails' to give it strength. We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. Some have the coil on top of the intake manifold, while some years and engines have the coil mounted to...

Used coil mounting bracket. This is the later Big Block V-8 version starting 1969. Found on 390 and 428CJ cars.We happen to know that there are no less than 4 different versions of factory Ford coil brackets used on 1967-73 Mercury Cougar and Ford Mustangs and literally all other Ford cars and trucks. This version is for big block V-8's, and has a 'flat' strap on the bottom, earlier versions had an additional reinforcing 'C' channel on the bottom. Probably used starting in 1969. Some have...

This is a complete set of four used headlight bulbs, marked with the FoMoCo logo. These sets come with two high beam and two low beam bulbs. Each bulb is tested by the electrical department. If you're trying to keep your Cougar or Mustang as close to original as possible, you should definitely grab a set.These bulbs are date coded, so if you want a particular date, be sure to mention it in the comments section of your order.  

Reproduction under dash light assembly for the 67 - 68 Cougar or 65 - 68 Mustang. This short style assembly was used on either driver or passenger side. There were two versions of this light, a long bracket version and a short bracket version. The driver side was always the same, but the passenger side typically used the longer version on cars with no A/C. Cars that had air conditioning used the shorter bracket style to keep from coming in contact with the A/C plenum. ...

C7WB-13K705-C-AGRADE Left side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13K705-C courtesy lamp assembly left hand side. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway. Hardest side to find in primo condition most get dinged up from errant seatbelts. This...

Left side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13K705-C courtesy lamp assembly left hand side. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses.Replaces Ford part number C7WB-13K705-C.Fits:1967 Mercury Cougar1968 Mercury Cougar ...

C7WB-13707-C Right side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13707-C courtesy lamp assembly right hand side. This is a grade "A" premium grade harness that is not sun damaged, spliced or damaged in anyway.

Right side courtesy lamp assembly attached to the door panel of all 1967 Cougars and 1968 Cougars with either decor or XR7 interiors. Courtesy light assembly tag numbers as listed in the 1967 Cougar Electrical assembly manual on page 16, C7WB-13707-C courtesy lamp assembly right hand side. This is a grade "B" good used light assembly, expect minor rust pitting on the bezel and scratched lenses.Replaces Ford part number C7WB-13707-C.Fits:1967 Mercury Cougar1968 Mercury Cougar ...

Rechromed Bezel for your door courtesy lights found on all 67-68 Cougars except the 1968 Standard model. These will require some patience with a dremel tool to remove the lenses from your cores and place them in these. Passenger and driver are the same, keep in mind the red lens goes to the back of the bezel. To be eligible for core refund, your cores can only show light pitting. ...

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check out our video on dash removal and restoration: ...

Used grade B driver side dash insert for the 67 - 68 XR7 Cougar. Will show some amount of fading and scratches. When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side. Check...

When purchasing this part from us it is best if you send in one of the dash parts you wish to match. The one pictured is the best we have to offer but the one that you need maybe faded which means a substantial savings depending on how faded of a bezel will be suitable for you needs. The best way to judge just how much fading has occurred on the panel is to remove the emblem for comparison purposes. Prices for our less than stellar woodgrain parts usually run $25-$85 for the driver side.Check...