1969 Ford Mustang

Master clip kit which includes following fasteners:Door courtesy and speaker Driver side apronEngine feedFirewallFront crossmemberGas tank senderHorn feedPassenger side apron below relayRadio cable to dashSide marker and headlightsTurn signal lights on hood scoopUnder dashVarious location zip tiesKeep in mind that there are many other fasteners on 1969 Cougars / Mustangs that are not in this kit. ...

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. About 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end.

Air Conditioning Clutch Feed Wire that runs along the driver side valve cover to the clutch on the compressor. 24 inches in total length. Starting in 1969 the female plug was of the water proof variety. Black plugs on either end. Replaces Ford Part #: C9ZB-19A885-B.

Wire harness extension that runs from the under dash harness to the A/C fan control switch on any 69 - 70 Cougar Standard or XR7, or the 69 - 70 Mustang.Ford part number C9ZA-19945-B

Complete 25 piece clip kit for the 1969 Cougar or Mustang. Keep in mind that this is produced as a Mustang clip kit, and although most clips are the same between Mustang and Cougar...not all clips apply to Cougar applications.   

This Screw fastens the plastic guide for turn signal wires next to column under the cone by steering wheel.

This short harness attaches to the black power wire coming from the starter solenoid and then attaches to the harness that brings the power back to the convertible top pump or power sunroof motor. This harness is for the 1969 XR7 or 1969 Standard and the 1970 Standard but it is not correct for the 1970 XR7 with power sunroof or convertible top as the 1970 XR7 used a rocker switch mounted in the dash pad located above the AC or AC block off plate. *NOTE* Side by side comparisons between 1969...

Preproduction wiring harness, connects the convertible top switch to the pump on both the xr7 and standard model Cougars and Mustang 1969 - 1973 convertibles.

This harness connects the convertible top motor to the under dash convertible top harness under the dash. Fits 1969-70 Mercury Cougar and 1969-70 Ford Mustang. This wire rests in the trough under the passenger side sill plate and goes behind the back seat where the convertible top pump is located.Ford part number C9ZB-15A668-B.

This harness connects the convertible top switch to the pump on both the xr7 and standard 1969 - 1973 convertibles.

This black wire attaches to the fusible link. The Fusible link connects to the starter solenoid with an eyelet connector, then connects to this wire with a billet connector. This wire then passes through the firewall to mate with the power top switch wiring under the dash. Correct for both XR7, Standard convertibles and power sunroof equipped Cougars in 1969, and Standard Cougar Convertibles in 1970.Casting Number: C9ZB-15A669-BFord Part Number: C9ZZ-15A669-BFits: 1969 Mercury Cougar Standard...

Used jumper wire used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Used wiring harness assembly specific to 1969 Mercury Cougar or Ford Mustang with H code 351W-2V or M code 351W-4V engines. Jumper harness about 9-1/2 inches long. Goes between the cowl plug for the engine gauge feed harness, and the engine gauge feed harness. Special with a 2 ohm resistance wire for the temperature gauge / sending unit. We believe that this wire harness was used specifically with the factory installed temperature sending units for 351W engines in 1969. Ford part...

This black wire attaches to the Circuit Breaker coming off the starter solenoid on one end then passes through the firewall to mate with the top switch wiring harness at the other end. We believe that some 1969 harnesses may have used a fusible link wiring harness in place of this one. This harness and the circuit breaker can be used on those applications.Ford part number C9ZB-15A669-B or C9ZZ-15A669-B.

Reproduction dash to console harness for your 69 - 70 Cougar or Mustang.

Main console wiring harness only, 1969 Mercury Cougar and Ford Mustang. Ford part number C9ZB-15A056-A and C9ZZ-15A056-A. Plugs for cigar lighter, shift indicator or PRNDL light, ashtray wiring harness plug, and heat/AC control. 15A056 harness only, secondary harnesses available separately.

Grade "A" harness that runs from the passenger side door jamb to the courtesy / C-Pillar light. This harness is only needed if you have a Standard model car. NOTE: All XR7's would have already come equipped with his harness.

This harness connects the rear speaker harness to the fader switch. Ford part number C8GA-18A900-BOverall length: 44"

For AM radio optional rear speaker. Ford part number C9ZB-18A900-BOverall length: 11' 7"

Quality wiring reproduction for Perfect Circle brand of speed controls as found on most 1968-1971 Ford - Mercury - Lincoln automobiles. Main harness with Ford part number 9A840, can be used on a variety of model and years. Harness connects the servo, has grommet for firewall, and connectors under the dash. Jumper wire to the brake pedal.

Used tilt / tilt away steering column wiring harness for the 1969 Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

For use on fixed columns only. Attaches to the bottom side of the column to keep the wiring in place. Fits all 1968-69 Mercury Cougar, Ford Mustang, Ford Torino, Mercury Cyclone.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Used radio light socket and wiring pigtail for all factory Philco AM radios as installed in 1967-70 Mercury Cougar and Ford Mustang cars. These light sockets are tested and cleaned, and have enough wiring lead to re-solder or crimp connect to your Philco AM radio. Original part with correct color wire.

Original used AM radio speaker lead wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustangs with factory AM radios. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios

Original used speaker lead wiring harness pigtail for all 69 - 70 Cougars and Mustangs with factory AM radios. This wire pigtail is located in the door.*Note - The only difference between this pigtail and the one listed for the 1967-68 dash speaker is the actual plug design.

New wiring pigtail with male bullet connector, and male / female paired connector. Also has rubber grommet that fits a 5/8" inch hole. Looks like 18 gauge wiring. These are remnants from the reproduction Mustang front turn signal lights that we convert to Cougar wiring. Brand new, approximately 13-15 inches in total length. Colors as shown.

Original used AM radio power lead wiring harness pigtail for the 67 - 71 Mercury Cougar and Ford Mustangs with factory AM radios. This double male plugged wiring pigtail solders to the your factory Ford AM radio. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail. Proper length for re-soldering to factory AM radios.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your driver side speaker, which is denoted by the orange wire. Red or black colored plugs are acceptable for the left hand speaker.Part of the stereo speaker wiring harness that goes to a pair of factory...

Original used stereo radio speaker wiring harness pigtail for all 1967-70 Mercury Cougars and Ford Mustangs  with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your under dash radio speaker wiring harness. We have a limited supply of these but also offer a quality reproduction version of this wiring plug pigtail.White speaker wire goes to the passenger side speaker, and the orange colored wire goes to the driver side speaker. This is...

Used turn signal wiring pigtail for the 69 - 70 Cougar or Mustang. Pigtail is from the switch side of the turn signal.

Used wiring pigtail from the under dash harness to the door jamb switch on the driver side of the 69 Standard Cougar / 69 Ford Mustang

Used wiring pigtail from the under dash harness to the door jamb switch on the passenger side of the 69 Standard Cougar / 69 Ford Mustang.

Used under dash wiring harness repair plug and pigtail to the windshield wiper switch for the Mercury Cougar XR7. It was also used on the Standard model after 3/3/1969. This is part of the 14401 main under dash wiring harness.

Used plug and wiring pigtail for the brake light warning switch located on the drum or disc brake distribution block mounted to the driver side fender apron. This is a plug and section of wire for repairing the underhood harness. Specific to 68 - early 70 Cougars and Mustangs.The only difference between the late and early pigtail is that the early plug is black and the late plug is white. No difference in wiring.

Reproduction under hood wiring harness repair plugs and leads that go from the under hood harness to the starter solenoid on the Mercury Cougar or Ford Mustang.  Sold as a pair.

Used wiring pigtail for the Windshield washer pump on the 1969 - 1970 Mercury Cougar or Ford Mustang.

Electrical wiring pigtail for the windshield wiper motors on any 1969-70 Mercury Cougar or Ford Mustang. Plug with grommet and correct color wires and an adequate amount of wire length to make a repair or splice onto the newer motors without plugs.

Reproduction ignition switch repair pigtail for your 68-69 Cougar and Mustang. This pigtail is not going to be a good fit, but if you choose this as your replacement, keep in mind that although this pigtail has an extra long resistor wire, do not splice into it or cut it down. Its resistance is dependent on its full length. This is a  cheap, inexpensive replacement, but we don't recommend it and would highly suggest going with one of our used pigtails instead.  NOTE - We've...

Used steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1970-72 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968-69, Ford, Mercury, & Lincoln. This plug is black, there is also a natural or white color version of this plug used by Ford 1968-69. Ford part number D0AZ-14489-L.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the...

Steering column wiring harness plug aka Turn Signal Switch Harness Connector. Replacement plug for all 1968 - 1969 Mercury Cougar and Ford Mustang, with tilt or fixed steering columns. Generic Ford part likely lots of applications between 1968 - 1969, Ford, Mercury, & Lincoln. Ford part number C8AZ-14489-S.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the...

Correct plug for your 67-71 AM- FM radio, or 8-track... Often these have been cut from the main loom to install an after market radio.The 1972 model used the same plug, but the wires are not in the same spots, go figure! These are speaker wires not power wires.The color codes are:  White right cowl speaker.   Orange left cowl speaker. Speaker blue / black ground. Power "not this listing." Blue / red stripe, radio light. Yellow / black stripe, power in for radio. ...

Exact replacement for that valuable AM-FM radio. This plug and pigtail is used to repair the radio out to speaker wiring so that it will plug into the plug for the speakers. Don't fake it and hack up your valuable under-dash wiring harness to make your original radio work! Fix it correctly the first time with this quality replacement piece.

This direct replacement is the 2 inch Y pipe only with 2-1/4 intermediate pipe outlets and is for any 1969-70 Mercury Cougar or Ford Mustang equipped with the 351W engine with stock cast iron exhaust manifolds. These units are manufactured right here in the good old USA from 2 inch aluminized pipes and made from an original 1971 Cougar and Mustang with the 351W 2V engine. We also sell OEM style dual exhaust systems that include the H pipe, mufflers, and tail pipes.*NOTE* Will not fit 351...

Reproduction engine side stud for the clutch equalizer bar or z-bar that fits a 289, 302, 351W, or 351C engines in the 67-70 Cougar or Mustang. 

This big book measures 18" x 13" x 3" and weighs 8 pounds. It's a must have if you are serious about electrical or vacuum work on the Cougar, Thunderbird, Mark III, Montego, Fairlane, Maverick, Cyclone, Bronco, F100, Torino, Mustang or other Ford products products from 1969. Condition is used and will have a few pages that have torn away from the rings. Form 7795P-69 Course 13003 and 1703

NOS 1983 Ford manual on how to read and understand vacuum diagrams. Although it's technically made for older cars, it has tons of useful information on how to decode diagrams. Includes sections on vacuum theory and applications, devices, hoses, schematics and system diagnosis. This handy book has information pertaining to how the engine creates vacuum, the carburetor and it's vacuum pressure regulation characteristics as well as air intake, fuel induction, emissions and ignition. As an...

New old stock, NOS, windshield wiper switch for any 1969 Cougar or Mustang. Marked C9ZB-17A553-A on the back. This is the two speed variety, the 1970 switch has a longer shaft than this 1969 version.

Reproduction emblem for the 390 engine designation. Never used on a Cougar, but an attractive emblem for customizing. Measures 3 1/8" x 3/4" and has two mounting studs.Replaces Ford part # C9ZZ-16637-D.