My Lists
Login
Subtotal
$0.00
Shipping
Tax
Discount
Total
*NOTE* According to Phil Parcels of the National Cougar Data Base Project, the approximate cut off VIN for determining EARLY...
This solid state sequential kit eliminates all the mechanical motor-driven sequencers and relays used in the trunks of the...
Our turn signal switches are made on the FoMoCo original tooling. If you have replaced your sequential unit in the trunk...
Reproduction dash pad in black for the 1967 and 1968 Mercury Cougar. This is the same Dashes Direct pad you see advertised...
NOTE: At the moment the supplier is only making the late model version of this beltline kit. The late version has a slight...
Another spot-on reproduction by WCCC! C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2....
Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines...
Correct fitting reproduction set of 4 wheel lip mouldings for the 67 - 68 Mercury Cougar Check out this video...
New LED dash light kit for the gauges in your STANDARD 67 - 68 Mercury Cougar. Finally, a kit that will provide you the...
New LED dash light kit for the gauges in your Mercury Cougar. Finally, a kit that will provide you the light you need to see...
This conversion will replace the old, tired, vacuum system that likes to leak and wear out. This kit consists of two BRAND...
This conversion will replace the old, tired, vacuum system that likes to leak and wear out. There are few differences...
Electrical wiring pigtail for the windshield wiper motors on any 1969-70 Mercury Cougar or Ford Mustang. Plug with grommet and correct color wires and an adequate amount of wire length to make a...
Original stereo radio pigtail and plug. From a 1972-73 Mercury Cougar or Ford Mustang stereo radio. Has correct plug, wire colors and makings for the plug that connects to the factory speaker...
Reproduction wiring pigtail repair kit for the sequential box on the 1968 Cougar. Included are: 1 four pin red connector1 four pin black square connector1 four pin white square connector1 four...
Reproduction ignition switch repair pigtail for your 68-69 Cougar and Mustang. This pigtail is not going to be a good fit, but if you choose this as your replacement, keep in mind that although this...
Used under dash wiring harness repair bare ignition switch plug for the 1968 Mercury Cougar. This is the plug only, no wiring pigtail, and is part of the 14401 main under dash wiring harness.NOTE: A...
New old stock manual steering worm gear for any 1967-70 Mercury Cougar or Ford Mustang with manual steering or 19:1 steering gear box. Factory new worm gear assembly for rebuilding your steering...
Used wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American...
Quality plexi-glass lens that is ready to install. Just peel off the protective tape and carefully pull your clock apart and replace and reassemble.The originals had a very slight concavity to them...
Reproduction 270 piece interior master fastener kit for the Mercury Cougar that fits both Standard and XR7. *NOTE* If you click on the selections below, they will take you to each of the sub kits...
New old stock toggle tips or 'handles' as Ford called them. Fits 1967 Mercury Cougar XR7 models. Ford part number C7WY-13B760-A. Do not put excessive force on the shaft as you may damage the switch...
New old stock toggle tips or 'handles' as Ford called them. Fits 1968 Mercury Cougar XR7 models. Ford part number C8WY-13B760-A. Do not put excessive force on the shaft as you may damage the switch...
Good original used toggle tip for the 1971 - 1973 Mercury Cougar XR7