All Products

Grade B used A/C center vent for standard (non XR7) model Cougars. These will have some defective chrome plating, and pitting. Fits the standard model (65A or 65C) Cougars with padded dash face pads. See our other listing for Grade A versions of this air conditioning center register or vent.*Note - Will not fit XR7 model Cougars.Replaces Ford casting number C7WA-19623 and C7WY-19893-A.

Grade B used A/C center vent for XR7 (non Standard) model Cougars. These will have some defective chrome plating, and pitting. Fits the XR7 model (65B) Cougars with woodgrain dash faces. See our other listing for Grade A versions of this air conditioning center register or vent. *Note - Will not fit Standard model Cougars. Replaces Ford number C7WY-19893-D.

Dash color painted steel bezel that houses the courtesy lights on all 1969-70 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL ACCY. Sold pit free, often times we can select your desired color, but plan on detailing them if your undergoing a restoration.Replaces Ford part number C9WB-10964. During assembly of your switches, note that the pins need to be on top. Switches and wiring harnesses sold individually. ...

Dash color painted steel bezel that houses the courtesy switches with DEFOG on all 1970 Mercury Cougar XR7's. This is the bezel that says MAP COURTESY PANEL DEFOG. May have some small pits, depending upon stock on hand. Plan on detailing them with your interior color for best results.Replaces Ford part number D0WB-10964-B. During assembly of your switches, note that the pins need to be on top. Switches and wiring harnesses sold individually. ...

Complete grade "A" bezel with perfect woodgrain and aluminum surround. The 1969 bezel is unique from 1970 in that 1970 had a curved cut-out for the larger diameter column. Notice the circular rings around the gauges are not discolored on this premium grade part.Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

Complete grade "A" bezel with perfect woodgrain and aluminum surround. The 1970 bezel is unique from 1969 in that 1969 had no curved cut-out for the larger diameter column. Notice the circular rings around the gauges are not discolored on this premium grade part. Check out the video below on our new gauge tester: ...

Complete grade "B" bezel will have faded woodgrain, dull aluminum surround and there will also be a few scratches or cracks. The 1969 bezel is unique from 1970 in that 1970 had a curved cut-out for the larger diameter column. Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

Complete grade "A" bezel with flawless woodgrain and aluminum surround. The 1969 bezel is unique from 1970 in that 1970 had a curved cut-out for the larger diameter column.Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts!

Complete grade "B" bezel with faded woodgrain, dull aluminum surround and a few scratches or cracks. The 1969 bezel is unique from 1970 in that 1970 had a curved cut-out for the larger diameter column.Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts! ...

Best used bezel we can find from a Western parts car "Almost" pit free. If you look close you will see some tiny specs. Click onto the image to enlarge the picture.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13064, and D3WY-13064-B.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.

These B grade headlight doors will have some pitting in the chrome. Some of them will be nearly pit free, but may have a small crack. Click onto the image to enlarge the picture.Replaces Ford part number D3WB-13052 and D3WY-13064-A.

Reproduction headlight switch bezel for any 1971-73 Mercury Cougar and Ford Mustang.  Replaces Ford part number D1ZB-11649-AC.

Incorrect chrome finish (supposed to be satin not chrome) Mustang part that requires modification to make the metal XR7 insert fit. This is the only new alternative to your broken bezel, we sometimes get in an original that just needs paint. This unit will also fit the Cyclone, Montego, and many other Mercurys and Fords. Replaces Ford part # C8ZZ-3D572-A.

This is the correct horn panel bezel for all 1968 standard model Cougar steering wheels. The satin paint will need to be resprayed but the two mounting studs are in place and there are no cracks or burns. Please see related for XR7 model bezel. Ford part number C8AA-3D754-A.

License to rear bumper spacer used on all 1973 Cougars. Usually this item is badly cracked or missing. This is a show quality used part for those that are concerned about less than obvious detail items.NOTE: The difference between the 71-72 version and this 73 version is that the 73 did not have a casting number and the earlier year versions did.

Poor condition with scratches and pitting as shown. This die cast bezel with a brushed finish was used from 1969 to the first part of 1970. The engineering number found on the back is C8AB-14505-B.

Good used bezel with no obvious scratches or pits. This bezel was used on the passenger door and both sides of the back seat in 1969 and on some earlier 1970 Cougars. The Ford engineering number found on the back is C8AB-14507-B.

Used grade "A" bezel used on the passenger side door and both rear seat switches. Looks similar to the 1970 bezel but is held in place with very hard to find clips not speed nuts. No pits or obvious scratches, Ford engineering number as seen from the back is C9AB-14A432-DFord part # is C9AZ-14528-A

Used grade A power window switch bezel for the Mercury Cougar. This bezel is used with all power window switches, except for the driver side door, and was only used on the 1973 model. Ford engineering # D3MB-14528-DA.

Good used bezel with obvious scratches and or pits. This bezel was used on the passenger door and both sides of the back seat in 1969 and on some earlier 1970 Cougars. The Ford engineering number found on the back is C8AB-14507-B.

Used grade B power window switch bezel for the Mercury Cougar. This bezel is used with all the power window switches, except for the driver side door, and was used on the 1973 model only. B grade, expect rust pitting in the chrome. Ford engineering # D3MB-14528-DA.

The Cougar radio bezel at first glance looks much like the Mustang radio bezel. It does in fact carry a Cougar part number and has a slightly different shape to it. The most noticeable difference is the fifth screw hole at the top middle, Mustang does not have this hole. Keep in mind the AM-8 track used the same bezel but with an enlarged hole.This enlargement was done at the factory prior to plating and if you look at the back side you will see the cut line. This is a pit free bezel that has...

The Cougar radio bezel at first glance looks much like the Mustang radio bezel. It does in fact carry a Cougar part number and has a slightly different shape to it. The most noticeable difference is the fifth screw hole at the top middle, Mustang does not have this hole. Keep in mind the AM-8 track used the same bezel but with an enlarged hole.This enlargement was done at the factory prior to plating and if you look at the back side you will see the cut line. This is a B grade bezel that has...

Used radio bezel that will show minor pitting and will most likely need the black area repainted. For use on cars with no console. Two different castings, need to be side by side to see minor difference. Ford part # C8ZA-18842 and C7ZA-18842.

This radio bezel is made by the original Ford supplier and features high quality die cast chrome. For cars without a center console. Replaces Ford Part #:C8ZA-18842-C.

Here's another quality reproduction with the correct camera case finish used on all 1969-70 Mustangs and Cougars except Xr7. Replaces Ford part # C9ZZ-6504774-B.

Both our A and B quality bezels will need the overlay replaced. Cosmetically this bezel will be as good as our grade "A" units, but when you turn them over you will notice one or two of the feet will be broken off. These missing feet may make it a little more cumbersome to install and if someone walks on your installed console these feet do provide support. Obviously it would be easy to glue on some feet (or spacers) but this item will install just fine without them. Most likely the white will...

Used shifter plate bezel for the Mercury Cougar or Ford Mustang equipped with a 3 or 4 speed manual transmission, but without a center console. This unit is a nice upgrade from the simple plain Mustang boot retainer. This version is the one held down with no screws, the rubber boot holds it in place. Part number C7WB-7262-D is the one being sold.Ford part # three different casting numbers with very slight variations. C7WB-7262-A, C7WB-7262-C, & C7WB-7262-D. Check out our video on...

Used driver side (left hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Used grade "B" passenger side (right hand) rear maker light bezel for the Mercury Cougar. We find that these are usually in better condition than the fronts, so we can offer you better quality at a lower price than we can the fronts. These same bezels can also be found on other full size 1970 Mercurys. Ford part # D0MB-15A466-A.

Used passenger side (right hand) rear marker light bezel for any 1971-73 Mercury Cougar. Originally painted body color, flush mounted to the passenger side rear quarter panel. Has two attaching studs, and sometimes one locating stud. We often times find that the locating stud is broken or cut off. You will want to cut the corner stud off if using the available reproduction Mustang red rear reflectors. All of our bezels will have the 2 larger studs intact. See related items for new lenses and...

Used grade "B" driver side (left hand) front side marker bezel for the Mercury Cougar. The 1970 Ford Torino and Maverick units look similar, but do not have the same angle or depth as the Cougar. These bezels are also unique to the 1970 Cougar. We do not have any of these bezels in "mint" condition, all of our lights will have minor blemishes like the unit shown. Ford part # D0WB-15A441-A.

Used grade "A" passenger side (right hand) front side marker bezel for the Mercury Cougar. The 1970 Ford Torino and Maverick units look similar, but do not have the same angle or depth as the Cougar. These bezels are also unique to the 1970 Cougar. We do not have any of these bezels in "mint" condition, all of our lights will have minor blemishes like the unit shown.Ford part # D0WB-15A440-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73...

Used grade "B" passenger side (right hand) front side marker bezel for the Mercury Cougar. The 1970 Ford Torino and Maverick units look similar, but do not have the same angle or depth as the Cougar. These bezels are also unique to the 1970 Cougar. We do not have any of these bezels in "mint" condition, all of our lights will have minor blemishes like the unit shown. Ford part # D0WB-15A440-B.

NOS bezel for the side marker lights on the Mercury Cougar or Ford Mustang. This is an original Ford replacement part. Used with front and rear 1969 marker lenses and fits almost all 1969 Ford and Mercury cars. Ford part # C9AZ-15A440-A, casting # C9AB-15A466-A.

Used grade "B" driver side (left hand) rear maker light bezel for the Mercury Cougar. We find that these are usually in better condition than the fronts, so we can offer you better quality at a lower price than we can the fronts. These same bezels can also be found on other full size 1970 Mercurys. Ford part # D0MB-15A466-A.

Used grade "B" bezel for the three spoke rim blow steering wheel found in the Mercury Cougar Eliminator or the decor equipped Cougar. Grade B bezels will have at least one broken stud and the decals will be showing signs of peeling. Ford part # C9WA-3D752-A.

Poor condition, sun faded bezel that needs restoration. We usually have 40 to choose from in all conditions ranging from $10-$175. No center emblem, plan on having missing or broken studs on the rear. May have come from either a decor or XR7 interior, meaning it could have one of two wood grain patterns visible.Ford part # C9WA-3D752-A.

Good used part with no peeling foil covering or cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. We also have these in grade "B" for $43.85. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate. ...

Good used part with a little peeling on the foil and this part will most likely have cracks. Of the three studs on the back you can rest assured one if not two of the studs will have cracks or a portion missing. Contact us for the many options as we have over 50 in stock. We sell the metal woodgrain painted center section separate.

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts.Ford part # C9WB-13449 for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source...

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts. Ford part # D0WB-13504-A for the driver side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great...

Used driver side 1971-72 Mercury Cougar tail light bezel. Minor blemishes, perfect driver quality. Mercury part number D1WY-13489-B. No Core required. Thinking about adding some LED taillight bulbs to your car? Here is great little video that shows the performance of LEDs and traditional bulbs side by side so that you can make an informed decision. ...

Used driver side 1973 Mercury Cougar tail light bezel. Minor blemishes, perfect driver quality. Mercury part number D3WY-13489-B. No Core required. Thinking about adding some LED taillight bulbs to your car? Here is great little video that shows the performance of LEDs and traditional bulbs side by side so that you can make an informed decision. ...

This is a poor condition bezel with pitting on all surfaces. It is a better than nothing type of part. We do not accept returns on grade C parts.Ford part # C9WB-13449 for the passenger side. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great...