Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 
Filter Products by


Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 3937-3984 of 4620
$0 Price: $55.89

Buy Details

Availability: Out of Stock
Item #: 25558 -

D3AZ-17A812-A Front bumper guard rubber pad used prior to September 5, 1972, on a 1973 Mercury Cougar. The early front bumper guards had a narrow rubber pad early on. The rear flat surface measures 3/4 inches wide. Same rubber strip either right or left side. Hard to find without some scaring on the rubber. This pad is not nearly as common as the wider one which measures about 1-1/8 inches wide.Replaces Ford part number D3AB-17A812-A.

$0 Price: $38.88

Buy Details

Availability: Out of Stock
Item #: 25559 -

D3AZ-17A812-B Front bumper guard rubber pad used after September 5, 1972, on a 1973 Mercury Cougar. These later front bumper guards have a rubber pad that measures 1-1/8 inches wide on the flat rear surface. Same rubber strip either right or left side. Hard to find without some scaring on the rubber. This pad is more common than the thinner 3/4 inches wide pad.Replaces Ford part number D3AB-17A812-B.

$0 Price: $26.85

Buy Details

Availability: Out of Stock
Item #: 32783 -

New old stock rubber fender to hood bumpers. Set of 4 NOS Ford. Replaces Ford part #: C6OZ-16758-A.

$0 Price: $30.00

Buy Details

Availability: Out of Stock
Item #: 33328 -

New Old Stock lower distributor bushing for most V-8 engines 1965 through 1968-69. Ford deemed this bushing as not needed during 1968. That is why all 351W distributors do not have one installed. All 289 distributors 1965-67 should have one installed, starting in 1968 some did, some did not. Many 1968-69 302-2V's and all Boss 302 distributors had them installed. Same with FE distributors all had them starting in 1965, by 1968-69, they were disappearing. Limited to stock on hand. If Ford deemed...

$0 Price: $50.85

Buy Details

Availability: Out of Stock
Item #: 15-0037 -

Used plastic bushing for the lock pawl rod guide for the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. These delicate little bushings are needed to keep the lock pawl rod in alignment with the vacuum motor shaft. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

$0 Price: $31.85

Buy Details

Availability: Out of Stock
Item #: 15253 -

This kit is for the clutch equalizer or clutch Z-bar on 1971-73 Mercury Cougars or Ford Mustangs, all V8 engines. All parts included as shown. *Tip - Add a liberal amount of grease to these parts during installation.

$0 Price: $27.35

Buy Details

Availability: Out of Stock, On Order
Item #: 31867 -

Reproduction ram cylinder bracket bushings for the 68 - 70 Cougar or Mustang. If you're having trouble with the bushings on your car ripping or tearing through the hole in your power steering ram cylinder bracket (more so with our reproduction drop down bracket), you can purchase this pair of polyurethane bushings to replace your existing ones. The boot kit we sell also comes with similar bushings, but are a lower quality item, so this set should solve your problem. Sold as a pair. ...

$0 Price: $50.85

Buy Details

Availability: Out of Stock
Item #: 25732 -

C60Z-6222454-B door handle hardware kit for 69-70 Cougar as well as select Torino / Fairlane / Cobra / Falcon

$0 Price: $89.87

Buy Details

Availability: Out of Stock
Item #: 11023 -

C9ZZ-2853-A Front emergency brake cable for all 1969-70 Mercury Cougar and Ford Mustang. Front cable attaches to the emergency foot brake. New Old Stock, measures 43-5/8 inches long.

$0 Price: $59.15

Buy Details

Availability: Out of Stock
Item #: 42001 -

This reproduction rear emergency / parking brake cable kit fits from equalizer to rear brakes. 2 required per vehicle. Equal length emergency brake cables for 1967 on both the Mercury Cougar and Ford Mustangs. Upgrading to the 1968 unequal length cables can easily be done. Equal length cables is correct for 1967 Mercury Cougar and Ford Mustangs. Fits L.H. or R.H., the Cougar uses a longer keeper than the Mustang to compensate for the added wheel base length. Replaces Ford part # C7ZZ-2A635-A,...

$0 Price: $77.85

Buy Details

Availability: Out of Stock
Item #: 25835 -

This is our heater cable for use with Mercury Cougars and Ford Mustangs with factory equipped A/C. The best part, its NOS, so you know it will fit right the first time! Ford part # C9ZZ-19988-A.

$0 Price: $95.00

Buy Details

Availability: Rare / NOS Part
Item #: 33238 -

New Old Stock cable for any 1971-73 Mercury Cougar. Cable only, handle needs to be replaced from your unit. Drift pin hold it onto the cable. Reuse your bezel too. Ford Part Number: D1WY-2760-A or D1WY-2A760-A This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not...

MSRP:$99.99
$99.99 Price: $61.85

Buy Details

Availability: Out of Stock
Item #: 14365 -

NOS heater cable for 1969 - 1973 Cougars or Mustangs that are not equipped with factory air conditioning.Ford Part #: D1ZZ-18518-A

$0 Price: $40.37

Buy Details

Availability: Out of Stock
Item #: 32716 -

This used emergency / parking brake cable connector is for the Mercury Cougar only. That is because it is longer than the Mustang version due to the Cougar's longer wheelbase. This connector connects the two ball ends of the long and short emergency brake cables. Ford part # C7WY-2A790-A.

$0 Price: $73.89

Buy Details

Availability: Out of Stock
Item #: 24065 -

Used passenger side (right hand) disc brake caliper mounting bracket that is a unique and one year only bracket for mounting the Kelsey Hayes twin piston caliper to the 1967 Cougar brake spindle. Tough parts to find in rebuildable condition. We won't always have them in inventory as singles unless we have multiples of these extra brackets for one side or the other. Ford part # C7OZ-2B134-A. Check out this video ...

$0 Price: $72.86

Buy Details

Availability: Out of Stock
Item #: 24027 -

1967 289-2V autolite 2100 carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base, 1.02" venturi size and 240 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note - Not for DSO 52 and DSO 53 California destined cars. ...

$0 Price: $65.57

Buy Details

Availability: Out of Stock
Item #: 24029 -

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-H stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

$0 Price: $65.57

Buy Details

Availability: Out of Stock
Item #: 24031 -

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-N stamped on the carburetor base, 1.02" venturi size 240 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

$0 Price: $65.57

Buy Details

Availability: Out of Stock
Item #: 24032 -

1967 289-2V carburetor, automatic C4 transmission - 49 states. C7DF-F stamped on the carburetor base 1.14" venturi size 300 cfm. Core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note not for DSO 52 and DSO 53 California destined cars. *NOTE - Take a kid for a ride in a classic...

$0 Price: $65.57

Buy Details

Availability: Out of Stock
Item #: 24033 -

1967 289-2V Autolite 2100 carburetor, manual transmission - 49 states. C7DF-S stamped on the carburetor base, 1.02" venturi size 240 cfm. Application for 3 and 4 speed manual transmissions. Rebuildable core carburetor with proper numbers, we don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. *Note - Not for DSO 52 or DSO 53 cars destined for California. *NOTE* Take a...

$0 Price: $65.57

Buy Details

Availability: Out of Stock
Item #: 24034 -

1967 289-2V Autolite 2100 carburetor, automatic C4 transmission - California DSO 52 and 53. C7DF-V stamped on the carburetor base, 1.14" venturi size 300 cfm. Core, rebuildable carburetor with proper numbers. We don't always have the factory Ford Autolite tag that was affixed to the top. PCV spacer plates also available and required for stock air cleaner clearance on top of engine. C code 289-2V engines and automatic transmissions. *Note-for use with California Thermactor smog equipped...

$0 Price: $74.57

Buy Details

Availability: Out of Stock
Item #: 41936 -

CARBURETOR SPACER PLATE, 0.28" thick, has correct tab marked "FRONT". Replaces Ford Part Number C8AZ-9A589-G

$0 Price: $75.87

Buy Details

Availability: Out of Stock
Item #: 24501 -

Factory two barrel carburetor spacer plate. Positions carburetor above intake manifold for proper linkage operation. With PCV fitting at rear. Unique to the X code 390-2V premium fuel engines.

$0 Price: $81.85

Buy Details

Availability: Out of Stock, On Order
Item #: 41935 -

CARBURETOR SPACER PLATE, 0.28" thick, has correct straight 1/2" PCV hose nipple in rear. Replaces Ford Part Number DOOZ-9A589-A. PCV System overview courtesy of Mansfield Mustang.

$0 Price: $75.02

Buy Details

Availability: Out of Stock
Item #: 11-0121 -

Grade B used A/C center vent for any 1967-68 Ford Mustang. Grade B will have a defect or two in the chrome plating.Replaces Ford number C7ZA-19623.

$0 Price: $32.85

Buy Details

Availability: Out of Stock
Item #: 33145 -

New Old Stock center cap emblem for the Mercury Cougar with XR7 hubcaps / wheel covers. On the XR7 package, this concave aluminum applique was applied to the center of the hubcap / wheel cover. Called an applique. Used only in 1968 on the one style XR7 hubcap. Not sure why it has a 1969 part number, error? Ford part number C9WY-1137-A.

$0 Price: $59.85

Buy Details

Availability: Out of Stock
Item #: 19185 -

Used chrome / black center cap for the 67 - 68 Mercury Cougar equipped with the wire spoke hubcaps / wheel covers.Fits:1967 Mercury Cougar1968 Mercury Cougar

$0 Price: $55.89

Buy Details

Availability: Out of Stock
Item #: 30450 -

Used chrome / red center cap for the 1967 and 1968 Mercury Cougar and Ford Mustang Equipped with the Wire Spoke Hubcaps / Wheel Covers. Fits:1967 Mercury Cougar1968 Mercury Cougar

$0 Price: $69.89

Buy Details

Availability: Out of Stock
Item #: 16801 -

The only reason you would buy an original used unit is that you would want to match your existing original caps. The reproductions we carry are actually much better quality than the originals, as they will never fall off. Chrome center cap with black background and chrome Mercury man logo. Came from the factory on 1967 and 1968 Mercury Cougars with Styled Steel Wheels, but will work on any 67-70 with Styled Steel Wheels. Fits the following models with style steel wheels: 1967 Mercury...

$0 Price: $69.89

Buy Details

Availability: Out of Stock
Item #: 22623 -

These original clip on center caps are an inferior design compared to our reproductions that screw on from the back. The originals had varying shades of blue, whereas the repro has a solid blue. The only reason you would purchase this fragile expensive used cap is to match what you currently have on a very original car. When using center caps on Legendary wheels, you will need these adapter plates. Ford part # C9WY-1130-BCheck out our center cap installation tips video below: ...

$0 Price: $87.89

Buy Details

Availability: Out of Stock
Item #: 11827 -

This XR7-G center cap adapter cone was used in conjunction with the RADER wheel and is needed to mount the center cap to the aluminum centered wheel. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know...

$0 Price: $52.88

Buy Details

Availability: Out of Stock, Discontinued
Item #: 13830 -

1970 Mustang with deluxe woodgrain console insert. Fits all 1969-70 consoles, but the 1969 console insert had the seat belt storage cups. NOTE: These inserts came with enough studs to fit multiple cars. When installing this insert, simply clip off the extra studs you don't need.

$0 Price: $38.85

Buy Details

Availability: Out of Stock
Item #: 32769 -

New old stock check valve for Bendix brake boosters. This is a white plastic check valve. Ford part number D0AZ-2365-A.Check the related items, for a reproduction rubber grommet.

$0 Price: $48.87

Buy Details

Availability: Out of Stock
Item #: 19023 -

This one in, one out design was unique to the early 1967 Cougar for the headlights. Also found on vacuum controlled options like the 1967 Mustang Cougar tilt / tilt-away steering column. This is a good used unit that has been tested and found to hold vacuum well. This valve is located a few inches behind the carburetor.

$0 Price: $72.86

Buy Details

Availability: Out of Stock
Item #: 24376 -

Screws onto the cylinder head smog tubes. Sold individually, two needed per application. Ford part number C8AZ-9A487-A.

$0 Price: $32.85

Buy Details

Availability: Out of Stock
Item #: 26501 -

This is the 100% correct Ford original battery hold down clamp. Stamped with D0OB10755A. Ford Part #: D0OZ-10718-B. Note: The battery hold down clamp offered by many Mustang / Cougar vendors as "Concours Correct" is actually for the 1974 - 1978 Cougar /  Mustang.

$0 Price: $28.89

Buy Details

Availability: Out of Stock
Item #: 25271 -

Yoke style factory exhaust pipe clamp. For 2 inch outside diameter exhaust pipes. Two piece clamp see picture Ford part number D1AZ-5A231-C.

$0 Price: $28.89

Buy Details

Availability: Out of Stock
Item #: 23900 -

Band or ring style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Comes with a course sheet metal type hex head bolt. Ford part number C6AA-5A272-A. *Not all 1969 & 1970 Cougars had 2-1/4 inch tailpipes from the factory. Check the outside diameter of your current tailpipe for fitment. Part number C5DA-5A272-B is the factory style 2" tailpipe clamp.

$0 Price: $28.89

Buy Details

Availability: Out of Stock
Item #: 25270 -

Yoke style factory exhaust pipe clamp. For 2-1/4 inch outside diameter exhaust pipes. Two piece clamp see picture Ford part number D1AZ-5A231-A.

$0 Price: $40.37

Buy Details

Availability: Out of Stock
Item #: 14164 -

Very hard to find clip that fastens the chrome power window switch bezel to the door panel. Two required per bezel. Ford part number D0AZ-14570-A. *NOTE* Early 1970 Models used the 1969 style of bezel and did not use this clip.Do you have questions about Glue-In vs Bolt-In glass? How about how to properly install Glue-In glass in your 1969 Cougar or Mustang? Check out our video below for some great glassy information!1969 Glue-In Glass: The Comprehensive Repair Guide Video ...

$0 Price: $49.86

Buy Details

Availability: Out of Stock
Item #: 30259 -

NOS rocker moulding end clip. Fits all 1968 Mercury Cougars. This clip is plastic and metal, it has a stud which goes through the body of the car. Sold individually, 4 total needed per car. Our all metal version of this clip is reproduced and is a better value. Find it here.Ford part number C7OZ-6221094-A.

$0 Price: $33.89

Buy Details

Availability: Out of Stock
Item #: 19699 -

Used grade A rocker panel clip for the 71 - 73 Mercury Cougar 

$0 Price: $33.89

Buy Details

Availability: Out of Stock
Item #: 19455 -

Ford part number C9WY-6510198-A. This is the metal rocker moulding clip that attaches the front and rear of the mouldings to the car in 1969 (except the Sport Special which only has them on the rear). In 1970 a Phillips screw held the rear end of the rocker moulding to the quarter panel on each side so just the fronts of the mouldings used these clips in 1970. Keep in mind that this same basic clip can be found on 1977-1979 Mercury Cougars and Ford Thunderbirds that were equipped with optional...

$0 Price: $29.85

Buy Details

Availability: Out of Stock
Item #: 30662 -

Set of seven used clips with reproduction stainless steel acorn nuts. These fit the best when using an original aluminum deck lid moulding on a 1967 or 68 Cougar. In 69-70 a stainless deck trim was used and the clip was all metal with no plastic coating. For more insight on this tricky trunk trim, check out our video below: ...

$0 Price: $85.85

Buy Details

Availability: Out of Stock
Item #: 33132 -

New Old Stock set of brushes only fits the Eaton brand of air compressor clutch. Pitts compressor clutch is the most common one starting in 1969. These are exact reproductions made from the original tooling.Ford part #: C8SZ-2979-A

$0 Price: $50.45

Buy Details

Availability: Out of Stock
Item #: 41789 -

This set of brushes only fits the Eaton brand of air compressor clutch. These are exact reproductions made from the original tooling. It is possible to reuse the FoMoCo stamped bracket from the originals and re-rivet to this version. Yes, you can make it sneaky concours. You would have to figure out the rivets though. See related items for core brushes with stamped Ford numbers. Pitts compressor clutch is the most common one starting in 1969. Replaces Ford part #: C5ZZ-2979. C7AA-2979-A ...

$0 Price: $71.87

Buy Details

Availability: Out of Stock
Item #: 24869 -

C9ZZ-7528-A Equalizer bar or "Z" bar for 351 cubic inch Windsor engines and Boss 302 Eliminators with manual transmissions. Both 3 and 4 speed manual transmissions. This is a used part and it will most likely show some wear form previous use.

$34.99 Price: $36.86

Buy Details

Availability: Out of Stock
Item #: 31437 -

Used clutch spring bracket that attaches to the brake / clutch hanging bracket. All 1967-68 Mercury Cougar and Ford Mustang with manual transmissions. Replaces Ford Part #: C7ZZ-7535-B.