All Products

Mounts to the rear of a 'turbo' style muffler. Left side bracket. Ford part number C7ZZ-5A246-F.

Mounts to the rear of a 'turbo' style muffler. Right side bracket. Ford part number C7ZZ-5A246-G.

The 289 used a transverse muffler with hangers on either end and dual exhaust was not an option. The 289 Cougars for 1967 also did not use a tail pipe hanger like their 390 brethren did, the tail pipes were free hanging. We have observed in the many 1967 parts cars in our yard that many Cougars have had an after market tail pipe hanger installed at some point. Many Cougars have a hanger welded or bolted to the passenger side tie down bracket.

This set consists of one tail pipe hanger and one muffler hanger, both were mounted on the passenger side of the car. The only cars eligible for single exhaust in 1968 were the C code 289 2V and the F code 302 2V, single exhaust never came on 1968 big block Cougars. In some instances 2 barrel cars had special ordered dual exhaust as an option from the factory. Probably the most common occurrence would be those few F code 302-2V engines installed in the ultra rare, ultra cool XR7-G. *Early...

This set consists of one tail pipe hanger and one muffler hanger, both were mounted on the passenger side of the car. The only cars eligible for single exhaust in 1968 were the C code 289 2V and the F code 302 2V, single exhaust never came on 1968 big block Cougars. *Later production after 11-1-1967

For all H code 351-2V engine codes with single exhaust. Includes 1970 351C or 351W engines. Includes one tail pipe hanger and one muffler hanger, both of which mount to the passenger side of the car.

This used bracket kit is what is needed to mount the headlight vacuum storage tank inside the front of the driver side front fender. This kit differs from the 1970 kit only in the slightly different design of fasteners used.

Includes all the hardware needed to mount your 1968 vacuum storage can located inside the driver fender. Parts do not come cleaned as shown, we clean many of these used parts so as to show the details and true condition of the part you can expect to receive.

Complete mounting kit for the vacuum storage tank located inside the front portion of your driver side fender.

All 1967 and 1968 Mercury Cougar includes both C code 289-2V and A code 289-4V engines. 1967 and 1968 only, 6-5/16 inches in diameter, 3/4 inches thick, cast iron construction with key way groove. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to keep a 100% original looking appearance on a concours car that does not get driven or see...

Ford casting number C8OE-6316-A All 1968 Mercury Cougar 302 engines. Includes both the F code 302-2V and the J code 302-4V engines. The 1968 302 harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/2 inches, and 1-7/8 inches thick. Ford casting number C8OE-6316-A2 is also an acceptable casting number. Ford part number C8AZ-6316-A. Has the timing marks on rim.  The rubber in this used balancer will be the original...

D0AE-6316-A All 1970-73 Mercury Cougar 351C-2V engines, and only the 1970 M code 351C-4V engine. The 1970-73 351 Cleveland harmonic balancers all have 4 bolt holes for attaching the crankshaft pulley. We save the very best used harmonic balancers, those that do not actually need rebuilding. Outside diameter is approximately 6-1/2 inches. Ford master part number DOAZ-6316-A. Crank shaft balancer, crankshaft dampener, harmonic balancer. Price includes $55 core charge. Refundable $50.00 core...

Includes all Ford 1973 H code 351-2V Cleveland engines only. Outside diameter is approximately 6-1/2 inches, and 1-1/4 inches thick. 1971-73 351-4V Cleveland have specific balancers, and are different than 1970-72 351C 2 barrel engines, please identify your engine and verify your balancer numbers. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for...

Includes both the H code 351-2V and the M code 351-4V engines. The 1969 351 Windsor harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-3/8 inches, and 3/4 inches thick. Crank shaft balancer, crankshaft dampener, harmonic balancer. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option...

Includes all 1970 H code 351-2V Windsor engines only. The D0OE-6316-C harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-1/4 inches, and 3/4 inches thick. 351-2V Cleveland and 351-2V Windsor engines were both used in 1970, they each have specific balancers, please identify your engine and verify your balancer numbers. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be...

Ford casting number D0OE-6316-B Includes all 1970-71 J or C code 429CJ engines. The D0OE-6316-B harmonic balancer is identified by the 4 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 6-5/8 inches, and 1-3/8 inches thick. Ford part number D0OZ-6316-B. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to...

Ford casting number C4AE-6316-A. All 1967 Ford S code 390-4V engines. 1967 (and earlier), 6-5/8 inches in diameter, cast iron construction with key way groove. This is a combination crankshaft balancer and pulley. Has the timing marks on rim. Ford Master Part number C3AZ-6312-E. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for those wanting to keep a 100% original looking...

Very nice reproduction of the D0ZZ-15525-A 1970 Mercury Cougar and Ford Mustang 4 speed backup light wiring harness, with the factory installed Hurst shifters. Plugs into the backup lamp switch and connects to the harness plug on the firewall behind the engine.

Nice thick foam. Chromed mounting post. Includes base plate for seat. Keep in mind we have good used for less money, several colors available in good condition. Find them here.

Reproduction pair of halogen headlights for any 67 - 73 Cougar or Mustang. These bulbs work for both high and low beam, you simply need to bend one of the tabs back for high beam (see photo above). Keep in mind that you will need a headlight relay kit when installing halogen headlights on your car.  Benefits of switching to halogen bulbs: Brighter lightDramatically improves driver visionOptical lens for a powerful beamLong range high powered lightsCrystal clear glass face with H4 halogen...

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

Sold as a pair, these were a one year only feature that allows you to quickly disconnect the hideaway headlight vacuum hose kit a few inches from the firewall. The fittings are slightly different so as not to mix up the connection by crossing the lines.

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1971-73 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. 

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL GRADE B ACTUATORS COME WITH A 60 DAY WARRANTY. You can find the seal rebuild kit here. Used grade "B" headlight door actuator for your Mercury Cougar. Every once in a while (not often) we will...

Requires you to PRE-PAY a core charge of $30. Used grade "B" headlight door actuator for your Mercury Cougar. This grade B actuator has been reconditioned with new seals but will still slowly leak down after time as not all of them will function as new after being reconditioned. These actuators are sold individually on an exchange basis or outright (for an additional core charge). One actuator actuates both headlight doors on the 69-70. This unit also comes with a 30 day warranty. Ford part #...

Used headlight wiring harness for either side of the Mercury Cougar. This harness is the sub-harness that connects your headlights to the under hood harness. The Cougar uses one per side and they are identical. Sold individually.Ford part # C9ZZ-13076-A, tagged C9ZB-13076-B.*NOTE* A pair of these units were also used on the 1969 Mustang and Mach 1. However, they were not used on the quad headlight 1970 Mustangs.

Contrary to what you might think at first glance, the support rods used in 1967 - 1968 Cougar headliners are not the same front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must keep the rods in the same order as they came out of the original headliner. To help you do this, Lincoln-Mercury coded each rod with a color applied to each end. From front to rear, the 1967 - 1968 color codes of the headliner rods are: None (this is the...

Reproduction LIGHT BLUE Interior Headliner for the 1967 Mercury Cougar. Correct Moon Crater texture available in most stock colors. This is a VERY light blue used on the early 1967 XR7 with dark blue interior. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark...

Reproduction BLACK Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of installing...

Reproduction BRIGHT RED Interior Headliner found in the very early 1967 Standard Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured)....

Reproduction DARK AQUA Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Reproduction dark ivy gold / dark green headliner for the 1967 and 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Thinking of installing your own headliner? Join in the discussion here for some helpful tips. Check out our video below showing how to install...

Reproduction interior headliner in light ivy gold / light green for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured)....

Reproduction MAROON / DARK RED Interior Headliner for the 1967 or 1968 XR7 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red and Dark Ivy Gold. Thinking of installing your own headliner? Join in the discussion...

Reproduction MEDIUM BLUE Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not pictured) and Dark Green (in Cougar called Dark Ivy Gold, not pictured). Thinking of...

Note: This is the correct color for a Parchment / Off-White interior in a Cougar. Reproduction PARCHMENT / OFF-WHITE Interior Headliner for the 1967 or 1968 Mercury Cougar. Correct Moon Crater texture available in most stock colors. We also have used headliner bows and used windlace in stock. Keep in mind you have to remove your front and rear glass to do a headliner correctly. This holds true when you replace your vinyl top as well. Now also available in Medium Blue, Dark Aqua, Dark Red (not...

Contrary to what you might think at first glance, the support rods used in 1969 - 1970 Cougar headliners are not the same front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must keep the rods in the same order as they came out of the original headliner. 5 Rods total. Once installed in the car, each rod should be about the same distance from the roof as the other rods. WCCC marks the bows with a sharpie pen, 1 hash mark, 2 hash...

Contrary to what you might think at first glance, the support rods used in 1971-73 Mercury Cougar headliners are not the same from front to back. Each of the rods is bowed to a different curve. To replace a headliner and make it look right, you must install the rods in the same order as they came out from the original locations. To help you do this, Lincoln-Mercury coded each rod with a color applied to each end. 1st. Driver Side: Pink - Passenger Side: Pink 2nd. Driver Side: Pink - Passenger...

We found that the plastic adjustment clip can break easily on these reproductions, so consider buying a good used original Ford part instead, for around the same price. Find it here.

Used headrest guide and retainer for the 69 Cougar or Mustang. The plastic adjustment clip doesn't break as easy as it does on the reproductions, so consider buying this good used original Ford part instead.When ordering please mention in the comments section what color you desire and we will do our best to accommodate.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

Exact OEM standards and specifications. Correct fiberglass insulation, fittings, rubber hose and S clip.

Exact OEM standards and specificatons. Correct fiberglass insulation, fittings, rubber hose and S clip.

This is the heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 2 Barrel Carburetor and the 351 Cleveland engine. Exact OEM standards and specifications. Correct fiberglass insulation, fittings and S clip.

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up.  Made out of OE Steel.  This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.

This is a 2 piece heat riser choke tube that provides heat to the choke, so the choke will open up as the motor warms up. Made out of Stainless Steel. This tube is designed to work on the 1970, 1971, 1972 & 1973 Mercury Cougar or Ford Mustang with a factory 4 Barrel Carburetor and the 351 Cleveland engine.