All Products

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here! Does...

This used original, color coded set of vacuum hoses is 100% complete and relatively pliable. It comes complete with decades of dirt and grime (patina) for no extra charge. If you want to remove the grime it will take some serious elbow grease but it can be done. The color coded stripes are quite resilient to cleaning as the ink used actually embedded itself into the rubber. If you have a tried and true method of cleaning these hoses let us know and if it sounds good we will post it here! Does...

New silicone radiator hoses for the 69 - 70 Cougar or Mustang with the 390 or 428CJ engine. The hoses are made with a sturdy black silicone, which will last longer than standard rubber hoses and has a higher burst pressure rating. Includes upper and lower radiator hose, and a bypass hose. To help enhance its performance, the lower hose is nylon-reinforced and comes with a stainless steel spring, which will keep this hose from collapsing and causing other problems. Replaces Ford...

Used rear driver side (left hand and passenger side (right hand) courtesy / opera light housings for the Mercury Cougar. The rear courtesy / opera light was standard on all XR7 Cougars, but were a popular option on decor and standard level interior Cougars. These units are marked LH for the driver side and RH for the passenger side. Also sold individually, see related items. Ford part # C7WB-13B729-C or C7WY13A744-C for the passenger side, C7WB-13B736-C or C7WY-13A744-D for the driver side....

New front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch front drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. Needs threaded studs, see related...

Used front drum brake hub for all Mercury Cougars equipped with front drum brakes. Pretty much fits most front 5 lug 10 inch drum brakes on all mid sized Ford and Mercury cars. Front drum brakes only. Fits 1967-69 Mercury Cougar and 1965-69 Ford Mustang with 5 lug 10 inch drums. Several manufacturers of the front drum assemblies such as Kelsey Hayes and Bendix were suppliers to Ford over the years. Quite a bit of labor to press these out. May or may not have threaded studs, or...

Dog dish style hubcap / wheel cover with the Mercury Man center cap for the Mercury Montego. This very rare optional unit was used in conjunction with the 14x6" 16 hole GT wheel commonly found on Mustangs and Torinos in 1968. This hubcap / wheel cover was offered only in 1968 and rarely seen on a Cougar as it would have only been offered as an over the counter option at your Mercury dealership. The more common application for this unit would be the 1968 Mercury Montego or Cyclone. No pitting,...

Excellent condition NOS "dog dish" style hubcap. Most early Cougars used the full hubcap / wheel cover, so this one is rarely found on a Cougar. We have seen these used on wheels painted the body color on basic Cougars as well as black painted wheels. Ford part # C8MY-1130-A

NOS hubcap / wheel cover that is new in it's original Ford box for your Mercury Cougar.Ford part # C7WY-1130-B This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash...

One year only, very hard to find in used condition with brilliant red, most have faded to pink or gray. Used on standard Cougar only. Ford part # C8WY-1130-BFits:1968 Mercury Cougar

Used grade "A" turbine style hubcap / wheel cover for the Mercury Cougar and Montego. Will have no obvious curb rash, the center will still show some red but usually will be faded and the paint will show some aging. These are the same as the 1969 Sports Special / 1968 Dan Gurney hubcap / wheel cover, but have the Mercury logo glued in the center. Ford part # C8GY-1130-G.Fits:1968 Mercury Montego

Used simulated wire spoke hubcap / wheel cover that is in above average condition with no curb scrapes. This listing is for someone who has removed their center from their current damaged cap and wants to save money by purchasing a cap with no center. The same cap was used on most all FoMoCo products including, but not limited to the Falcon, Mustang, Fairlane, Comet, Galaxie, Montego and LTD. Only the center logo changed from one car to the next. Ford part # C7WY-1130-C. ...

Used wire spoke hubcap / wheel cover for the 69 - 73 Cougar. These units are above average with no scratches where they have rubbed the curb, almost pitting in the center and faint, if any fading in the logo.Ford part # D0WY-1130-DFits:1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar ...

Used wire spoke hubcap / wheel cover for the 70 - 73 Cougar. Will have no obvious curb scratches, pits in die cast, bent spokes or cracks in plexi center. Ford part # D0WY-1130-D Fits: 1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar

Used Grade "A" XR7 hubcap / wheel cover for the Mercury Cougar. This wheel cover was used on the xr7 and it can also be found on Ford Mavericks but with a different center medallion. Grade A will not be perfect but will not have obvious curb rash and the center medallion will still have good color. If you have grade A caps like this one we are buyers.Ford part # D1WY-1130-E.This is the same cap as found on the 1973 - 1977 Ford Maverick. The Maverick has a different plastic center and carries a...

New Old Stock aka NOS XR7 shield hubcap and wheel cover for the 1969 Mercury Cougar with a WHITE inner ring. There were two versions of this cap, one with a white painted ring around the center, and one with black around the center. This white version was used in 1969, with the black version being used in 1970. Ford part # C9WY-1130-B. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store...

Reproduction hydraulic cylinder for the Mercury Cougar or Ford Mustang convertible equipped with the power top. Includes pictured pivot bushings.* - According to the manufacturer and the Ford Master Parts Catalog, 1971 Mustang would have originally used the passenger side cylinder (D1ZZ-7650600-A) for both sides.Replaces Ford Part #: D1WY-7650601-A, D2ZZ-7650601-A

Reproduction hydraulic cylinder for the Mercury Cougar or Ford Mustang convertible equipped with the power top. Includes pictured pivot bushings.* - According to the manufacturer and the Ford Master Parts Catalog, 1971 Mustang would have originally used the passenger side cylinder (D1ZZ-7650600-A) for both sides.Replaces Ford Part #: D1WY-7650600-A, D1ZZ-7650600-A, D2ZZ-7650600-A

Connecting to the Convertible Frame Lift Lever and the Convertible Hoses, the Convertible Top Hydraulic Cylinder creates pressure from the fluid transferred by the hoses. Each Hydraulic Cylinder consists of light-weight aluminum casing, a durable steel rod, and includes all bushings and gaskets. Part is made through innovative engineering and rigorously tested to provide you with the best in functionality and long-term dependability.  Precisely crafted with high grade materials...

Air conditioning belt tensioning pulley with new bearing. This adjustable bracket and pulley was used on all 1970-73 351 engines that came with A/C, as well as 1970 428CJ & 1971 429CJ. This part often has a casting number of D0AA-8A617-C1 but not always. This adjustable idler pulley is identified by having the large bearing pulley. Same as the C8AZ-8678-A adjustable idler pulley only with a small bearing pulley. We also offer a bearing replacement service to rebuild your adjustable idler...

Air conditioning belt tension pulley. For Cougars and Mustangs with the 289 or 302 engine built between 1/3/1967 and 3/1/1968. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C7AZ-8678-B. *NOTE* Must be used with the C7AA-2888-G cast iron lateral support brace. ...

Used A/C belt tensioning pulley with new bearing. Ford standardized some of the brackets starting in 1968. This adjustable bracket and pulley was used on all 1968-69 390 / 428CJ engines and 1968 289 and 302 engines after 3/1/1968. Additionally it was on 1969 351W engines as well. This adjustable tensioner pulley is identified by having the small bearing pulley. Same as the DOAZ-8678-C adjustable idler pulley only with a big bearing pulley. *Note* All new bearings will have a slight bit of play...

NOS, new old stock bracket and pulley assembly with new installed bearing for 1968-69 Cougar or Mustang equipped with the 390 or 428CJ engine. We also offer a bearing replacement service to rebuild your fixed idler pulley, see item 27539. Ford part # C8AZ-8678-B. ...

Air conditioning fixed idler pulley for Ford or Mercury with the 289 engines. 1965, 1966, early 1967 Ford and Mercury full and midsized cars all with 289 engines and factory air conditioning. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C5AZ-8678-D. ...

Used bracket and pulley assembly for Cougars and Mustangs with the 289 or 302 engine built after 3/1/1968. All pulleys are sold with new bearings installed.  If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! We also offer a bearing replacement service to rebuild your 289 or 302 fixed idler pulley, see item 27539. Replaces part # C7AZ-8678-C. ...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which were used starting in...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 351W or 351C engines. Sometimes has Ford number D0AA-8A617-A stamped on the bracket, not always.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which were used starting in 1968, now have an ever so slight amount of play....

Air conditioning fixed idler pulley for Ford or Mercury with the 352 / 390 / 410 / 428 engines. These are all sold with new bearings. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got what you need! Ford part # C5AA-8A919-C and C5AZ-8678-C ...

Used bracket and pulley assembly for 1967 Cougar or Mustang with 390 engines. All pulleys with bearings are sold in working used condition. If your pulley only needs a bearing, don't sweat it. Click this BEARING link, we've got the parts you need! Ford part # C7SZ-8678-B. ...

Used bracket and pulley assembly with new installed bearing for Cougars or Mustangs equipped with the 428CJ engine. This is also a service replacement part for the C8AZ-8678-B fixed idler pulley. The only difference between them is that this part has the larger bearing.*Note* All new bearings will have a slight bit of play in them. This is by design, by the manufactures. We have asked the suppliers, and the answer is to allow for possible heat expansion. Even the "Koyo" branded ones, which...

Used inner and outer driver side (left hand) wheel house as cut from a parts car. This is a hard part for us to obtain as we have to sacrifice all surrounding parts to remove it in its entirety. The almost always will have a substantial amount of rust showing at the very tips of the outers where they end behind the wheel. If you want to save shipping costs we can sacrifice the inner wheel house and sell you only the outer portion.Used inner and outer driver side (left hand) wheel house as cut...

Full driver (left hand) side front frame rail measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Full passenger (right hand) side front frame rail that measures 52" long and the outer rail has weld nuts installed for proper installation. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar 1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang ...

Used tilt / tilt away column shaft for the Mercury Cougar or Ford Mustang. Inner shaft with tight U-joint and perfect steering wheel mounting threads. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Quality inner wheel house made by Dynacorn patterned off of Grade A used panels provided by West Coast Classic Cougar.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box.

Quality inner wheel house made by Dynacorn patterned off of Grade A used panels provided by West Coast Classic Cougar.We also sell these as a complete set of four, which will save you money on shipping as we unbox them and nest all four together and fit them in one box. ...

This is for your automatic transmission 1969 Cougar XR7, Standard, Decor or Eliminator console. The 1969 is unique over the 70 in that it has a provision for your seat belt buckles. This requires an additional woodgrain insert, we also have one listed that does not require the additional insert (no holes). Absolute perfection in every detail, if all reproductions were this nice there would be almost no market for used parts. *Note - This console part does have pre-drilled holes for installing...

This is for your automatic transmission 1969 Cougar. The 69 is unique over the 70 in that it has a provision for your seat belt buckles. This does not require an additional woodgrain insert. Absolute perfection in every detail, if all reproductions were this nice there would be no market for used parts.

This is for your three or four speed manual transmission 1969 Cougar. The 69 is unique over the 70 in that it has provision for your seat belt buckles to be stored when not in use. This requires an additional woodgrain insert, we also have one listed that does not require the additional insert (no holes). Absolute perfection in every detail, if all reproductions were this nice there would be no market for used parts. *Note - This console part does have pre-drilled holes for installing the...

This console bezel is for your three or four speed manual transmission 1969 Cougar. The 69 is unique over the 70 in that it has a provision for your seat belt buckles. This does not require an additional woodgrain insert, so it is not technically correct for your Cougar. We list this unit because there is no quality XR7 burl grained inserts available at this time and some customers prefer the clean uncluttered look of the plain camera case finish. Absolute perfection in every detail, if all...

Grade "A" condition with rich luster on the woodgrain. Will have a few minor blemishes usually on the XR7 emblem and aluminum surround. No dents or scratches.Here’s a little inspiration for you to get our vinyl overlay kit and wrap your own parts!

This set of three woodgrain dash inserts for the Mercury Cougar without A/C are not as good as our grade "A" unit. However, it will work well for your daily driver. These retain an original looking finish and we carefully match these under bright lights to ensure they match color wise. This dash insert may have some slight scratches, dings or other blemishes, and all four toggle switch labels will be in place. Click here for the A/C version with the center hole.Here’s a little inspiration for...

This set of three woodgrain dash inserts for the Mercury Cougar with A/C are not as good as our grade "B" units. However, it will work for your lower quality daily driver. These retain an original looking finish that may be faded due to age and we carefully match these under bright lights to ensure they match color wise. This dash insert will have scratches, dings, or other blemishes, and all four toggle switch labels may not be in place. Click here for the non A/C version.Here’s a little...

This set of three woodgrain dash inserts for the Mercury Cougar with A/C are not as good as our grade "A" unit. However, it will work well for your daily driver. These retain an original looking finish and we carefully match these under bright lights to ensure they match color wise. This dash insert may have some slight scratches, dings or other blemishes, and all four toggle switch labels will be in place. Click here for the non A/C version without the center hole.Here’s a little inspiration...

This set of three woodgrain dash inserts for the Mercury Cougar with A/C are not as good as our grade "B" units. However, it will work for your lower quality daily driver. These retain an original looking finish and we carefully match these under bright lights to ensure they match color wise. This dash insert will have scratches, dings, or other blemishes, and all four toggle switch labels will be in place. (although the pictures may not be correct, you will get the correct A/C parts).Here’s a...

Reproduction inspection plate cover for all 390-4V and 428CJ engines with a manual transmissions, both 3 and 4 speeds. All years 1967 - 1970. Access cover to the flywheel and clutch.Replaces Ford part number C3AZ-6366-A.

This listing is for a used complete 1972 Standard instrument gauge housing with gauges and printed circuit board included. All gauges and circuit boards are tested, functional and will come with a 90 day guarantee. You'll actually save money buying this complete assembly as compared to buying the gauges, housing and circuit board individually. Each housing may have been constructed from multiple assemblies. Ford casting number on housing D1WF-10848 Check out...

Complete bezel, no cracks and no extra holes drilled and vibrant woodgrain insert. The difference between 71 and 72-3 is that 71 has no provision at the top for the seatbelt warning light. When you order please mention which interior color you have and we will try and accommodate. We suggest using a Mowtow "chrome touch-up" pen to touch up the chrome areas. Ford casting number D1WB-6504438-BW ...