All Products

Found on the lower radiator core support. 2 clips total, attaches the wiring harness and the vacuum hoses for the headlight system.Replaces Ford part number 377359-S.

Reproduction BLACK lug nut fits all Legendary Series wheels. 14mm x 1.5 threadSold individually. 

Chrome tapered acorn lug nut for use with the new Legendary wheels. This 13/16" nut really only fits the Magstar style - the others have tighter clearances and you'll want to use the 3/4" nuts made for these wheels. Sold individually here, or in a complete set with valve stems. Replaces Ford Part #: C9ZZ-1012-B.Check out our video on Legendary Wheels below: ...

Correct 3/4" tapered chrome acorn lug nut for the new Legendary Wheels. These are what we recommend you use with these wheels, since the clearances are too tight for regular 13/16" lug nuts. Sold individually here, or as a complete set with valve stems.Check out our video on Legendary Wheels below: ...

Reproduction lug nut for the Legendary GT7 Series wheel. Sold Individually. You can find the complete lug nut installation kit here.Check out our video on Legendary Wheels below: ...

Chrome acorn lug nut for most any Ford steel wheel including styled steel, Magnum 500,  new or reproductions.Replaces Ford Part #: C9ZZ-1012-B.

This is a standard reproduction lug nut that Fits the styled steel wheels and is the same as the original. 1/2"-20. Need to replace missing, cross threaded, or otherwise damaged lug nuts? Do you have after-market chrome wheels with the flat washers and closed round head lugs? Fits the following models with stamped steel wheels: 1967 Mercury Cougar 1968 Mercury Cougar 1969 Mercury Cougar 1970 Mercury Cougar 1971 Mercury Cougar 1972 Mercury Cougar 1973 Mercury...

Standard stamped steel wheel lug nuts in good used condition. 1/2"-20. Need to replace missing, cross threaded, or otherwise damaged lug nuts? Do you have after-market chrome wheels with the flat washers and closed round head lugs? Fits the following models with stamped steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972 Mercury Cougar1973 Mercury Cougar Should have a set of 5 in the trunk for use with your stock steel spare...

Used lug nut for your 1967 - 1970 Cougar

A close economy reproduction of the original Chrome acorn style lug nuts that fit the styled steel wheels. These stand just a little shorter than our other, more accurate reproductions.They don't have the correct matte finish, have a smaller head section and longer edges, but do still have the pointed top. If you are not building a show car then you may want to go with this generic version. Fits the following models with styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury...

Finally! A close reproduction of the original Chrome acorn style lug nuts that fit the styled steel wheels. These premium lugs nuts stand just a little taller than the originals, hard to detect unless you have them side by side with NOS.They have the correct matte finish and pointed top. If you are not building a show car then you will want to buy the brighter, generic version that you can find here. Fits the following models with styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969...

These open lug nuts are commonly used on drag strip or race cars . They will accommodate the aftermarket extended studs which are prevalent in all forms of racing. Plated bright silver zinc. Extended Thread design will work on any Legendary Wheel. 3/4 hex allows plenty of room for sockets. 1/2 x 20 threads. Check out our video on Legendary Wheels below: ...

Reproduction nylon lug nut protectors. These are sold in pairs, and come with 3/4" and 13/16" sizes. Simply slide one of these sleeves into your socket and keep the chrome on your lug nuts in perfect condition!These protectors are simple plastic and are prone to breaking. Can be used on a variety of other vehicles with the same lug nut size. For the 3/4" lugs, use the sleeve with a 7/8" socket. For the 13/16" lugs, use the sleeve with a 15/16" socket. ...

Ford manual transmission flywheel and automatic transmission flex plate mounting bolts. 6 bolts required, sold individually. Replaces Ford part # 378172-S

Reprint of an original pamphlet that was intended to help Ford techs date and identify by using the codes found on the parts. Covers all LFM models, 23 pages.

Complete reprint of the 1968 Vacuum Schematic for the Mustang.  You can find the free download for the headlight vacuum system here.

These little rivets are used to affix the ID tag to the passenger side of the 3 and 4 speed top-loader transmissions. Most tags are held in place by two rivets but on some only two are used from the factory.

Reproduction intake manifold spacer for the Mercury Cougar or Ford Mustang equipped with the 390 or 428 engine. Sold individually, # VI.

This little switch is mounted on the back side of your interior temperature control panel on most 1969-72 Ford products. It energizes the A/C pump when you move the the knob to the "A/C" position. Correct dimensions and easy to install. Starting sometime in 1972, this switch was incorporated with the vacuum selector manifold. This is part of the switch assembly C9ZZ-19B888-A.

Tired of your mirror falling out of adjustment? This installs easily and is correct in all details. Unlike the two piece unit we offer this one has the correct satin finish and correct screws. Replaces Ford Part #: C2SZ-17690-F. Reference from mercurycougar.net: Best guys to always talk to about Cougars..will take the time on the phone with you, call you back if you leave a message, got all the time in the world for you when you're talking 'cause you're important to them. Greatest thing for...

Reproduction exterior mirror pad for the passenger side sport mirror on any 1969 Mercury Cyclone or Montego, or 1969 Torino, Ranchero, etc., all with factory sport mirrors. Nice quality plastic reproduction sport mirror pad. Marked C9OB-17C701-A.Replaces Ford part number C9OZ-17724-A.

Driver side (left hand) mirror pad / gasket made of very soft rubber. Fits 69-70 driver side Sport Mirrors, and 69-70 driver side chrome mirrors on the Mercury Cougar. Will not work on the passenger side. While this is "better than nothing" it will never fit or look correct. We highly recommend purchasing our good used hard plastic mirror pad that is especially contoured to fit the door on the driver side. Replaces Ford Part # C9WY-17724. Do you have riv-nut questions? Here are riv-nut...

Replaces Ford Part #: D2AF-12029-AA

Three required per car, held in place by Allen head bolt, fits in the three slots at the top of the column tube.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.Fits: 1968 Mercury Cougar1969 Mercury Cougar 1968 Ford Mustang1969 Ford Mustang ...

D0WY-9A225-A "L" shaped mounting bracket for the rear evaporative vapor separator, mounts in the drivers side trunk well. *Note - This is only a small part of the 9B004 assembly.

There is not a special part number for this mounting bracket that was originally spot welded to the front of the headlamp switch. We offer these for use with our reproduction headlamp switch. This adapter or retainer is needed to correctly keep the headlamp switch at the correct angle to the lower metal dash. 1967-68 Mercury Cougar.

Repro fuel pump gasket for 1967 - 1970 Cougars or Mustangs with 289/302/351W/390/428CJ engines.

Nut for attaching brake boosters in any 1967-73 Mercury Cougar or Ford anything, including Mustang. 3/8 - 16 zinc plated nut with serrations.

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the course threaded nuts on the 1971-73 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Replaces Ford part # 55806-S

Reproduction nuts for mounting the 1969 Mercury Cougar headlight door or eyelid cover to the hideaway headlamp hinge.

Reproduction pair of mounting nuts for any 68 - 70 Cougar or Mustang with power brakes.

Used mounting plate for the heater blower motor on the 67 - 68 Cougar or Mustang without A/C.

Used on the backside of all but the driver side door panel. The screws that hold this plate on may be available upon request for an additional charge.

4" mounting Plate for Standard Spare Tire. Replaces Ford Part #: C5ZZ-1424-A.

3 1/8" Style Steel Wheel Spare Tire Hold Down. Available in Black or Chrome. Ford Master Parts Catalog indicates that this hold down was found on some 68 and 69 Cougars with SS Wheels. You may need to bend the ears in slightly to get them to fit properly inside the hole in the center of the wheel. Replaces Ford Part #: C8MY-1424-A.

Sold individually. Phosphate & Oil (gray-black)

This specialty screw attaches the gas pedal to the throttle linkage. Fun fact: the head looks like Phillips (and that works fine) but this is actually designed for a Pozi bit.

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Reproduction side view mirror screw. These screws are sold individually. Do you have riv-nut questions? Here are riv-nut answers!

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Fits 1967 Standard and XR7 Cougars or most Ford and Mercury with inside rear view mirrors. Also used on the 1967 xr7 hash marks located on the rocker.

1/4-20x1 inch stud. Sold individually. Found on various years and parts of Cougars. Used for attaching 1967-68 grilles to the headlight buckets. Also as replacement mounting studs for front and rear fender and quarter extensions. Zinc Dichromate (yellow-rainbow)

10 of these are used to mount the 1968-71 Cougar hood scoop found on the 68 428 CJ, 1969-70 Eliminator, 1969-70 428 Ram Air equipped Cougars, and 1971 GT and 429CJ. Sold individually Zinc (dark silver).

Door window glass grommet or washer to protect the glass for the Mercury Cougar or Ford Mustang. These units are placed under the bolts for mounting the window stops and the channel bracket. Used on most full and mid sized Ford

This gasket seals the fresh air tube in the cowl to the heater box inlet on 1967 through 1970 Cougars.