Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
Reproduction heater resistor attaching pins correct for 1967-68 Mercury Cougar and Ford Mustang, but works fine with 1969-73 cars too. Sold in sets of 2 pins.
Used retaining bolt with nut for the fixed column on any 70 - 73 Cougar or Mustang. 2 of these bolts are required to holt the two sections of the upper column sleeves together. Sold individually, 2 per column.
Good used 1970 factory installed clip for attaching the high pressure line to the power steering reservoir low pressure tube. Kind of kept the line oriented during installation of the high pressure fitting. For all 1970 Mercury Cougar and Ford Mustang with 351W, 351C or Boss 302 engines. This is more for reference, this clip is much smaller than the one found on 1971-73 Mercury Cougar and Ford Mustangs with power steering. Basic Ford part number in 1970 chassis manual is 3E506. No...
Spring steel clip located under the drive cable housing as seen on page 16, figure 19 of our free download of the sunroof panel service procedure manual.
Great reproduction of a rather hard to find part.
Replaces Ford part #C0AZ-9A307-B.
Good used ring with only surface rust and no obvious gouges.
Used retaining ring for the fuel sending unit or vent on 1971 and newer tanks. Fits a little tighter than the reproduction rings. Ford part #C0AZ-9A307-B.
New lower windshield moulding retainer screw. The retainers slide into the lower stainless steel windshield moulding and attach with these screws into the cowl top. #8 x 1/2 inch hex washer head screw with 1/4 inch drive. Several suppliers or styles of screws were used, some with plain hex some with a slotted hex. We stock the 1/2 inch length #8 hex head washer head screws. Sold individually, 7 total clips hold in that lower windshield moulding on 1969-70 Mercury Cougar and Ford...
We all love the look of classic sealed beam headlights, but the dim halogen light output makes nighttime driving potentially risky for you and your beloved classic. Holley's new RetroBright LED Modern White Headlights offer a number of advantages over traditional sealed beam headlights such as plug and play compatibility, better visibility, and 6 times longer life. Not only that, but because they are LED they take up less space, create far less heat, and use less power than other headlights....
Reproduction pump end return hose for the 67 - 70 Cougar or Mustang. Cut to 2' length.
High Quality 400 PSI pump to valve return line. This is the control valve to the return hose that comes from the power steering pump on all big blocks and the 1969 and 70 small blocks, and will work for the 1967 or 1968 small blocks with the 5/16 inch control valve fitting if the power steering hoses are routed the same as on the big block engines. The big block routing is far superior to the original routing as the original routing was susceptible to rubbing against the exhaust manifold. This...
Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.
We have created all of the components needed to economically install the steel nutsert or Riv-nut for the exterior mirrors that mount to the car doors. Our steel Riv-nut uses a 1/4 inch hole. You will need a 5/32 Allen or hex key, 3/8 inch wrench, and a 7/16 inch wrench. The Riv-nut needs to be assembled on the kit as shown prior to installation. The assembly is installed flush, in the pre-drilled hole. The Allen wrench and the 7/16 are held stationary, while the 3/8 wrench is used to tighten...
If your original is pitted or has come apart this will easily snap in place to remedy the problem. The finish on the repro differs a little from original.
The Rocket "Strike" provides timeless and classic traditional styling at very affordable prices. The Rocket Strike is a 1-piece wheel precision crafted from A356 aluminum and topped off with a vintage style aluminum o-ring center cap. It has a lug centric design and uses standard 60-degree conical seat lug nuts (sold separately). There is 3.00 inches of hub clearance under the center cap. Load rating is 1560 lbs per wheel.4.25 Back spacingFully polished center and outer rim. Cast...
Used roller for any 1969-70 Mercury Cougar or Ford Mustang hardtop or convertible rear quarter glass channel. Often times one of the little branches breaks off and allows chattering of the window movement. Included is a good roller and drilled out rivet. These can be reused if you drill out the center of the rivet and using a tap, cut threads into the hole of your desired machine screw or bolt size. Re-install with a washer and you are done.
Replaces Ford Part Number: B7A-12200-A / DR-5 And C5TZ-12200-A / DR-87 (Service Replacement)
This decal can be used to overlay your replacement oil filter, so it looks more like a vintage original oil filter. Research indicates that the gold was primarily used on 66 and earlier, as was the red. They then phased the red/gold out and replaced it with the white oil filter printed with the Autolite logo. 1967 Cougar/Mustang could have come factory installed with either red or gold. 1967 - 1969 factory serviced cars could have gotten the red or gold until stock was...
This is the type of material that was used to install gasketless windshields starting in 1969. Tom, at KTL Restorations shared this product with West Coast Classic Cougar. Product comes as a 3/8 inch diameter continuous round bead, coiled in 15 foot lengths.
Permatex RTV gasket maker for the automatic transmission in your Mercury or Ford. Great stuff for sealing up that leaky transmission pan gasket!
New RTV gasket maker for use on the differential of your Mercury or Ford. This gasket maker is specially formulated to withstand today's gear oils and prevent leakage.
New RTV oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.
New rust treatment in aerosol form for the Mercury or Ford. Provides one-step treatment that destroys old rust and prevents new rust. Just spray it on. Within minutes, rust is replaced by a durable black polymer coating that may be painted. Excellent protective primer. Follow directions for use, wear gloves it does not wash off readily.*NOTE* This item can only be shipped via UPS ground. No Foreign orders please. ...
Automatic chokes had been the norm for many years so a notice to the operator was a must. Decal Text:NOTICEThis vehicle is equipped with a manual choke located immediately below the ignition switch. For proper starting use manual choke. ...
Sold individually Zinc with Bi-wax sealer (dark silver with gold color on threads)
Concours? almost, these are stainless steel screws with the wax tipped coating like the originals, for installing the door sill plates. The wax was deemed necessary by the Ford Motor Co. as a seal. These can be used on all years 1967-73 Mercury Cougar, Ford Mustang and most all other Ford, Mercury, Lincoln cars of the era. Works well with any of the reproduction sill plates, these were really made to be used with the premium reproduction sill plates in stainless steel. 1967-68 Cougar and...
New hex head screw for attaching the fuel filler neck to the rear body. 67 to 70 Mercury Cougar and 1965-70 Ford Mustang. 1965-68 filler necks require 4 of this style screws. 1969-70 filler necks require a total of 5 hex head screws. #10 x 3/8". Replaces Ford number 42120-S8.
Original style fuel tank installation screw. 3/8 inch hex head. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks. See item 11942 for the kit of 12 screws, better value.
Original style fuel tank installation screw kit. 3/8 inch hex head. This is a set of 12 new screws. Black phosphate finish on this reproduction, originals were plated. Fits all 1967-70 Mustang and Cougar fuel tanks.
Sold individually. Two needed for globe box cable 1967-70 Mercury Cougar. 3 needed for installation of turn signal switches 1967-73 Mercury Cougar or Ford Mustang.Ford number 379203-S. Phosphate & Oil (gray-black)
Individual screw for attaching the headlight retaining ring on any 1967-70 Mercury Cougar or 1965-70 Ford Mustang, and pretty much most all other Fords during those years. #8 stainless steel screw. Two needed per headlight bulb retaining ring. A total of 8 would be needed for a quad headlight system on all Cougars.Replaces Ford part number 375452-S.
Sold individually Zinc Dichromate (yellow-rainbow)
Sold individually. Zinc (dark silver)
Reproduction Phillips head screw that is used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Sold individually. 24 required per car, set of 24 also available. ...
24 Reproduction Phillips head screws that are used in a variety of applications on the Mercury Cougar or Ford Mustang. This phosphate & oil (gray-black) colored unit features a wide flat head and is used for attaching the stainless roof side weatherstrip rail. However, it has other interior applications as well. Also sold individually.
Three required per car, includes washer. Used in conjunction with a steel clip to secure lower flange to column tube.
Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...
Used unique Phillips bright finish screw that attaches cable guides to roof.
Sold individually Attaches the lens to the light housing. Fits all 1967-70 Mercury Cougar or Ford Mustang.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...
8-32 screw for attaching the window regulator drive arm slide, to the rear channel bracket on 1969-70 Mercury Cougar and Ford Mustang with glue in glass. 8-32 Phillips oval head machine screw.
Fits Standard and XR7 Sold as a Set as Pictured.
One size fits all. Set of 4. Good replacement if not worried about show quality. 1967 – 1968 Coupe 6 Required per car 1969 – 1973 Coupe 4 required per car 1969 – 1973 Convertible 2 required per car Will also work on the 69 - 73 shifter bezels. 4 required. Not recommended for our Mass Backed Carpeting. Please see related items for the longer screws. Replaces Ford Part #: 381571-S
Fits all Mustangs, Cougars, Fords 65-70. Attaches the striker on the door pillar, the big screws. Little known fact: these aren't Phillips head screws, they are actually Pozi head / Pozi-Driv screws. While you can usually get a large Phillips screwdriver to work, the correct tool for these fasteners is a size 4 Pozi bit.
These are the screws that are used to attach the door latch to the door shell on the 67 - 73 Cougar or Mustang. Sold in a set of 6.
New set of 8 chrome headed screws for installing original or reproduction door speaker covers on all 1969-70 Mercury Cougars and Ford Mustangs.