Your cart is empty!
Our shopping cart requires the use of cookies. If you have your cookies disabled, please enable them for our site to place an order. If you have cookies enabled and have added an item to your cart, but you are still seeing this message, that could indicate that the cookie for our shopping cart is corrupted on your computer.You should be able to fix this by either:
Buy Details
New Old Stock Ford small block Ford distributor shaft to engine block gasket, made of rubber. Fits all 260, 289, 302, 351w, 351c engines. 1959-76. This is a "O" ring rubber washer. Will not fit big block FE, 360, 390, 410, 427, 428 engines. Ford part number B9TF-12143-A.
New Old Stock Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.
Ford FE distributor shaft to engine block gasket, made of rubber. Fits all FE or 352, 360, 390, 410, 427, 428 engines. 1958-76. This is a tapered rubber washer. Will not fit small block Windsor or Cleveland engines. Ford part number B8A-12143-A.
NOS C7ZB-6522449-A Driver side small size pad or gasket for the exterior door handle. Driver side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.
NOS C7ZZ-6522428-A Passenger side large size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.
NOS C7ZB-6522448-A Passenger side small size pad or gasket for the exterior door handle. Passenger side only, application 1967-68 Mercury Cougar and 1967-70 Ford Mustang as well as 1970 and newer Maverick and Comet with the early style chrome door handles.
Made from fuel resistant cork like original. Modeled off the Mustang \ 69 Cougar gasket which has 5 screws (67-68 Cougar only used 4 screws), but works for any 67-73 Mustang / Cougar. For 67-68 Cougar applications you will have to just screw through the cork. We can say with out a doubt, that in both Dearborn and San Jose, the factory workers did not use the pre-drilled holes when installing the fuel filler necks. We have suggested that the supplier not make them with holes. Probably...
Replaces part #C0AF-9276-A. Goes between fuel sending unit and tank.
Door lock and trunk lock gasket as found on all 1969-73 Mercury Cougar. Gasket used to seal the lock cylinders to the exterior door on all 1967 - 1973 Mercury Cougar and Ford Mustang as well as the trunk lock gasket on all 1969-73 Mercury Cougar. It is not used for the trunk lock cylinder on the 1967 - 1968 Mercury Cougar because they uses a flip up trunk lock cover that instead uses a gasket between the covers housing and the trunk. Replaces Ford part #C7AZ-6243625.
Gasket, for the C6 transmission filter. Fits all c-6 transmissions 1967-73 Mercury Cougar and Ford and Mustang.
Gasket for mounting the oil filter adapter to any FE or Ford 360, 390, 410, 427, 428CJ engine. Name brand gasket, fits all 1967-70 Mercury Cougar or Ford Mustang with S, X, R, Q, or W code engines.
OEM Cork Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.
Rubber Style Oil Pan Gasket. Four Piece Gasket. 1967-70 Mercury Cougar and Ford Mustang, includes 1969-70 G code Boss 302 engines.
OEM Style Oil Pan Gasket. Four Piece Gasket.
One piece molded rubber gasket with metal core. Keeps the rails flat and rigid, and prevents damage from over-tightening. Made by Fel-Pro. Oil pan SnapUps are included for easy mounting. This is by far the best oil pan gasket on the market.
New outer axle gasket for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars. One required per side, two per car.
Replaces Ford part #C7AZ-13568
Thermostat Housing Gasket BY FEL-PRO® Replaces Ford Part #: C5AZ-8255-A.
Thermostat Housing Gasket BY FEL-PRO® for the 351 Cleveland.
Adhesive-Backed Gasket Material Helps Prevent Breaking of Water Outlet. Gasket Cement is Not Needed. Self-Adhesive Backing Holds Thermostat in Place While Water Outlet is Being Installed.
Thermostat Housing Gasket By FEL-PRO® for the Big Block. REplaces Ford Part #: C7ZZ-8255-D.
New water pump plate gasket for the Mercury Cougar or Ford Mustang.
New water pump gasket for FE Ford engines. 1967-70 Mercury Cougar and Ford Mustang with 390/427/428CJ engines. Single gasket, two gaskets needed for installing your water pump. Price is for one gasket only.
Premium quality, exact fit plastic gasket set for both the driver and passenger side door handles. Also fits 66-71 Ford Fairlane and 70-71 Cyclone / Torino as well as several other Mercury, Ford Lincoln models. We are the exclusive retailers in the U.S. for this quality kit.
New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1964-73 small block Ford engines with size 260/289/302 cubic inches. C code 289-2V, A code 289-4V, F code 302-2V, and J code 302-4V.*Note - Excludes 1969-70 Boss 302 engines.
New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits all 1970-73 Ford 351C engines with 4 barrel intake manifolds 1969-70 Mercury Cougar and Ford Mustang with 351C-4V engines. This gasket set includes a metal valley pan.Any doubts? 351 Windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 351W engines. *Note - Excludes 351C-2V Cleveland engines. ...
New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1967-70 big block Ford engines with size 390, 427, or 428 cubic inches, FE engine only. 1967-70 Mercury Cougar, Ford and Ford Mustang.
New timing cover gasket set for 1967-70 Mercury Cougar and most all Fords with 289/302/351W engines. Gasket set includes; timing cover gasket, crankshaft seal, water pump gasket for early or late water pumps, and the oil pan corner gaskets under the timing cover.
New timing cover gasket set for 1970-73 Mercury Cougar and Ford Mustang with 351C engine. Includes gaskets as shown, timing cover, water pump to timing cover, fuel pump, crankshaft seal, and oil pan saddle.
New timing cover gasket set for the 1967-70 Mercury Cougar and most Fords with 390-2V, 390-4V, 427-4V, and the 428 Cobra Jets. Gasket set includes; crankshaft seal, timing cover gasket, two water pump gaskets, fuel pump gasket, and oil pan to timing cover gasket.
Cork valve cover gaskets for any big block Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.
Rubber valve cover gaskets for any FE 390 or 428 Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers.
Cork gasket for the disc brake splash shield. Fits all 1968-73 Mercury Cougar and Mustang and 1968-71 Ford mid size including Torino, Cyclone, Ranchero, Fairlane.Replaces Ford part number C8OZ-2B160-A.
Seals the lenses to the light body mounted in the front valance. Replaces Ford part # C9WY-13211. Sold as a pair. Also used on 1970 Mach I and 1969 - 1970 Shelby.
Seals the chrome marker light bezel to body. Seals the chrome marker light bezel to body. Their function is to keep water from entering the trunk around the rear lights. No gasket is needed on the front side markers. Replaces Ford part #D0ZZ-15447. These are designed for the Mustang and do not fit the Cougar without trimming. Sold as a pair.
These white foam gaskets fit between the sealed lens assembly and the chrome side marker light housing. They are sold as a pair. Replaces Ford part number D0ZZ-15209. *NOTE* To separate the sealed plastic lens assembly from the chrome bezels you will have to gently break away the edges of the factory "melted over" plastic stud. A drop or two of your favorite adhesive will reattach them but this is not crucial as the two threaded studs keep everything tied together once they are mounted back to...
Replaces Ford part #C9ZZ-6344228, sold as a pair. This is our economy version.
These are Concours quality with correct bevel and markings.. Sold as a pair.
Cork valve cover gaskets for any 289/302/351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.
Rubber valve cover gaskets for any 289 302 351W Ford engine. Sold in pairs, works well with either stamped steel or cast aluminum valve covers. Excludes Boss 302.
NEW PRODUCT! This gauge tester can be used to test all gauges on any Ford vehicle from 1956 to 1983. We are privileged to be one of the first companies able to offer this new product that has long been needed by the classic car community. Now you can quickly determine if the gauges in your car are accurate with this gauge tester. You can verify the high medium and low reading for your gauges, and also shows that the Instrument Voltage Regulator is working. If you own a...
Reproduction bolt in four piece clear glass set for the 1970 Mercury Cougar convertible. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions...
Reproduction bolt in four piece smoked glass set for the Mercury Cougar convertible. This set does not include any of the window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. Then there is this version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are reproductions of original...
Reproduction four piece bolt in tinted glass set for the 1970 Mercury Cougar or Ford Mustang convertible. This set does not come with any window trim so save yours for reuse. There are three versions of this glass. The clear version is just that, clear with no tint. There is a tinted version that will have a slight green tint to the glass. There is also a second tinted version that is called smoked and this version has a grey / brown tint to the glass. The clear and the tinted versions are...
1969-1973 20 amp Buss style glass tube fuses sold in a package of 5 and used in multiple positions. They are used for accessory feed, seat belt warning, tilt swing column, speed control, door ajar, low fuel, and power window relay.
1969-1970 30 amp Buss style glass tube fuses sold in a package of 5 and used for air conditioning.
1967-1970 7.5 amp Buss style glass tube fuses sold in a package of 5 and used for courtesy, glove box, luggage compartment, clock, tachometer, and radio pilot lights. Fuse length 7/8"