1968 Ford Mustang

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

Reproduction intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Used intermediate pipe exhaust bracket for the 67 - 70 Cougar or Mustang. Used on big block vehicles equipped with the transverse muffler. Attaches to the resonator exhaust hangers just before the muffler pipe rises above the rear end. Sold individually, 2 required per car.

Rubber isolator used in tilt away steering column near the lower bearing. Two required per car. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This mounts at the top front corner of the driver side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531491-B or C7WB-6531491. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

This mounts at the top front corner of the passenger side rear interior panel. Ford called this part a "Cap - quarter trim panel upper". All 1967-68 Mercury Cougar and also used on 1968 Ford Mustang coupe with deluxe interior or body code 65B.You may also need the attaching screw. Replaces Ford part number C7WY-6531490-B or C7WB-6531490. Fits 67 CougarFits 68 CougarFits 68 Mustang with body code 65B ...

Factory knob for the new for 1968 rear window defogger. This is the knob for the 2 speed fan switch mounted to the bottom dash on cars so equipped. Rare option, we try and match these up to the switches. Spares occasionally come in, subject to availability.

Used emergency flasher knob for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This unit is a very fragile part which we never find in good used condition. What you will see when it has been broken off is an exposed Phillips screw head. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes...

Hard to find knob with no crack or peeling issues, correct for right or left side Torino, Cougar, Mustang. Not for use with console equipped Mustang and Cougar. Casting number is C8OA-18A932-B.

Used on the Mercury Cougar or Ford Mustang with a factory center console and measures 1-3/8 inches tall. Replaces part # C8ZA-8A932-B

This is correct for your 1968 non console Mustang or Cougar. Fits left or right, no cracks or peeling. Casting number is C8ZA-18817-E.

Reproduction radio knob used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits: 1968 Mercury Cougar

Used on Mercury Cougar or Ford Mustang with a factory center console. Replaces part # C8ZA-18817Fits:1968 Mercury Cougar

This set of knobs is for 1968 Cougar / Mustangs without factory console. The exception to the rule would be the XR7G. Cougars equipped with a console need the longer version of this knob to clear the padded console face. If you happen to have a 1969 or newer radio then the radio has longer shafts and these knobs may in fact work with a console. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 68-70 AM radios with rear speakers and...

Good used set of four knobs for your Mercury Cougar or Ford Mustang with a factory center console. These are plastic and much deeper than the non-console version. The radios that would not utilize the white plastic spacer would be 1967 radios with factory rear speakers, 1968-70 AM radios with rear speakers and 1968-70 AM-FM radios, if you need the white spacer we offer it here. Our blow-out price is based on the fact that these are now available new! Knob length 1 1/2"Sleeve length 1 5/16" ...

Used Carter fuel pump lever. From Carter made fuel pump as installed on Ford 352, 390, 410, 427, 428CJ FE engines. Many of the Carter "X" fuel pumps with screw together rebuildable pumps often times have Ford small block levers. Housings are he same. Levers are removable, see youtube for the rebuilding and assembly procedure.

These plates show almost no wear and would look right at home on a show car.NOTE: The plates and plate numbers pictured are exactly what you'll receive.

These plates show average wear and can be used as is, or restored to look new.NOTE: The plates and plate numbers pictured are exactly what you'll receive. 

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair could use a bit of restoring to get back to perfect condition, but they are in good shape and will not have any extra holes like the grade B plates do.   NOTE:  "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Hard to find pair. This letter series would have been issued in 1968-1969. This particular pair has extra holes drilled, which would need to be repaired (see pictures). They could be restored or used as-is. Because of this, we're selling them at a reduced price. NOTE: "Due to programming limitations, a license plate that still has a record on the database cannot be reassigned. Therefore, customers returning to California after registering their vehicle out of state cannot have their old...

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

This rechromed lid is found on many years and cars 1968 - 1971. The diameter of the lid is just over 17 3/4", fits on 17.84" air cleaner bases. Application Mercury Cougar Ford Mustang 302 and 351 engines without ram air. Ford / Mercury have had various part numbers listed for this basic lid over the years. The primary difference was the original lids included an engine size sticker. That is why there are so many listings, the basic part number is 9661. This lid was chromed in several...

This used assembly includes lamp socket, bracket, mercury switch, and length of wire.Replaces part # C7ZB-15702-A

Used Link for 1967-68 Mercury Cougar and Ford Mustang with speed control. The Link is a tubular shaft for the Rod. It attaches to the Trunnion. Ford part number C7ZZ-9D768-A.

NOTE: WE SUGGEST LOCAL PICK UP ONLY FOR CORE ENGINE BLOCKS BECAUSE WE CANNOT GUARANTEE BLOCKS WILL NOT HAVE CRACKS INTERNALLY. Long block, factory J code 302-4V V-8 engine. Rated at 230 Hp with 10.0:1 compression ratio in 1968. Likely 0.030" bored motor that may or may not have been in running condition when pulled. Guaranteed to be rebuildable. Complete engine less carburetor, distributor, exhaust manifolds, fan, accessories, pulleys, and flex plate. Intake manifold and oil pan are included...

Used only in 1968 Manual 3spd and 4spd on non xr7 models and Mustang. Very hard to come by with no splits, burns or cracks. We rarely can supply the color you desire but please let us know your desired color and we will try. Grade A will not have UV ray damage and will look right at home in a low mile car. Satisfaction guaranteed.

Rare find, must have for your Concours Cougar. Sold individually.Ford part number C5ZZ-1012-BFits the following models with Styled steel wheels:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1967 Ford Mustang1968 Ford Mustang1969 Ford Mustang1970 Ford Mustang

Reproduction GOLD HAZE lug nut cover deigned to fit the Cobra / Eleanor style Legendary LW90 wheel.  Sold as a set of 4 and includes 20 Legendary low profile lug nuts.

Reproduction set of 20 lug nuts used specifically on the Rocket Racing wheels. These lugs will not work on any other wheel.

Nice used original Rotunda, over the counter dealer accessory. Stainless steel construction, weighs just under 8 pounds with hardware. Actual dimensions are 20 1/2 inches wide, 48 1/2 inches long, and the back lip is 3 inches tall. Installation hole spacing is as follows. Rear spacing 47-11/16" on center, front spacing (nearest the rear window) is 47-9/16". The spacing on short sides are 18-3/4" on center. This rack was utilized for may years on many cars. The same company made them for...

RAN-D or RAN-D1 Original equipment 3 speed top loader 3.03 transmission from a 1967 - 1968 Mercury Cougar with engine code C - 289-2V, or engine code A - 289-4V only. Could also have a casting number of RAN-D1. Ford master part number C5ZZ-7003-V.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each...

RAT-U Original equipment 3 speed top loader 3.03 transmission from a 1968 Mercury Cougar with engine code F - 302-2V, or engine code J - 302-4V only. Ford master part number C5ZZ-7003-Z.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%)Percentage of each transmission;X = 46.8%W = 33.6%U = 9.5%1 = 7.2%5 = 2.5%6 = 0.5% ...

RAT-N1 or RAT-N2 Original equipment 3 speed top loader 3.03 transmission from a 1968 Mercury Cougar with engine code S - 390-4V only. Transmission with casting number RAT-N2 also used during this model year. Ford master part number C8ZR-7003-E. *Note - RAT-N could also be sustituted.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame...

C5ZZ-7400-C3Assembly Factory 3 Speed manual transmission shift control assembly for any 1967 - 1968 Mercury Cougar and 1965 - 1968 Ford Mustang, 1968's only up until 1-2-1968. Includes shifter mechanism, shift rods, and shift lever. All in used condition. The 1-2-1968 date was the transition of the stronger trunion for the shifter mounting. The Ford MPC states that this same shifter was used on 6 cylinder Mustangs and all V8 Mustangs and Cougars as large as the 390-4V engine. Check out our...

RUG-E2 Original equipment 4 speed top loader transmission from a 1968 Mercury Cougar with engine code C - 289-2V, engine code F 302-2V, and engine code J 302-4V only. Ford master part number C6ZZ-7003-E. Bare transmission. Percentages of Cougars equipped with a manual transmission by year 1967 = 18.5% 1968 = 13.2% 1969 = 10.5% 1970 = 7.8% 1971 = 2.8% 1972 = 1.5% 1973 = 0.7% Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were 25.2%) Percentage of each transmission; X = 46.8% W...

RUG-M3 Original equipment 4 speed top loader transmission from a 1969 Mercury Cougar with engine code S 390-4V only. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear. Ford master part number C7ZZ-7003-E.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were...

RUG-AE or RUG-AE1 Original equipment 4 speed top loader transmission from a 1968 Mercury Cougar with engine code R 428 Cobra Jet only. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear. Ford master part number C8ZZ-7003-B.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame...

RUG-AD Original equipment 4 speed top loader transmission from a 1968 Mercury Cougar with engine code S 390-4V only. Transmission code 6 on the door tag, this would be a close ratio 4 speed transmission with a 2.32 ratio first gear. Ford master part number C8ZZ-7003-A.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were...

RUG-M2 Original equipment 4 speed top loader transmission from a 1968 Mercury Cougar with engine code S 390-4V only. Transmission code 5 on the door tag, this would be a wide ratio 4 speed transmission with a 2.78 ratio first gear. Ford master part number C7ZZ-7003-C.Percentages of Cougars equipped with a manual transmission by year1967 = 18.5%1968 = 13.2%1969 = 10.5%1970 = 7.8%1971 = 2.8%1972 = 1.5%1973 = 0.7%Total for 1967 to 1973 = 10.1% (Mustangs for the same time frame were...

New old stock Bendix master cylinder for 1968-69 Mercury Cougar and Ford Mustang with factory power disc brakes. This is a Bendix manufactured MC with proper 2227161 number and stop bolt on the bottom. Also has the dimple forward of the front brake line.  Includes a new cap with diaphragm as shown. The cap is not assembly line correct as this is a service replacement part.*Note even though this is a brand new unit, it should be tested for leaks prior to installation. Things happen when...

New Old Stock Ford C4 or C6 transmission modulator valve for 1967-73 Mercury Cougar or 1965-73 Ford and Mustang. Also known as the throttle valve, this valve controls vacuum to the transmission as you press the gas pedal, and it will apply higher control pressure for better quality shifts at higher RPMs. Ford part number C4AZ-7A377-B.

NOS big block motor mount. Left is the same as right, sold individually. This isolator is used with the 390, 427, 428 and 429 Cobra Jet engines.  Sold individually. Ford Part #: D1ZZ-6038-A.

Used engine or 'motor' mount for any 1969 Mercury Cougar or 1967-69 Ford Mustang convertible. There is not a replacement engine mount for the 1967 cars with 289 engine. These have the Ford casting number of C7ZA-6038-F, in the rubber. The mounts that we have in stock are a 30 year accumulation, needless to say it is very limited supply. They all appear to be in good shape without cracks in the rubber. We offer them for those enthusiasts that want correctness for concours judging, we suggest...

Keep in mind that if you have the original motor mounts in your 1967 with a 289 or 1969-1970 convertible these mounts will not work. Nobody sells motor mounts for them, period. This is contrary to what every auto parts store will tell you. Your options are to purchase our (used 68-70 frame stands) or modify your existing ones.Sold individually, two required per car, left is the same as right.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

Reproduction pillar post mouldings for the Mercury Cougar or Ford Mustang that feature two 2" gauge pods on the driver side. Sold as a pair.

Driver side upper windshield mouldinig. Suitable for restoration or could fit right in on or your lower quality daily driver. Ford part number C5ZZ-6503145-B.

NOS upper moulding at the top of the windshield on the left hand side. Ford part number C5ZZ-6503145-B