1967 Mercury Cougar

Good used, rust free valance with provisions for rear bumper guards. Getting to be hard to find without excessive filler. We have a local body man take out the small dents and he does not load them up with Bondo. He removes the filler and works the dent out properly. If you have the optional rear bumper guards then you will want a valance like the one pictured that has the factory holes for them. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car. We do...

Decent used, rust free valance that will need substantial work. Getting to be hard to find without excessive filler. These are not paint ready, flawless parts but rather 40 years old, taken from a parts car that will have small dents, creases and often some amount of filler. We do have NOS and on occasion we get in a flawless used example.Ford part # C7WY-6540544-A.

Vacuum tested working hot water valve for Mercury Cougars and Ford Mustangs equipped with factory A/C. This valve stops the flow of warm coolant when the A/C is on and has the original cast brass valve with bracket and vacuum pod. We are unable to guarantee that the water seal is good. Ford part # C7ZZ-18495-A, casting number on vacuum valve C7ZA-18C310-A.

Core C-4 Transmission valve body for any 1967-68 Mercury Cougar or 1967-69 Ford Mustang with code "W" transmission code on the door tag. This is only for 1967 through 1969 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in...

Core C-4 Transmission valve body for any 1968 Mercury Cougar or 1968 Ford Mustang with code "W" transmission code on the door tag. This is only for 1968 transmissions with P-R-N-D-2-1 shift pattern. Also known as the 8 bolt valve body. Sold as a core, should be thoroughly cleaned and rebuilt with quality parts. These units can be upgraded with 'shift kits' to firm up shifts, add longevity, and they help reduce and eliminate clutch and band slippage. Various kits available in the aftermarket,...

C6ZZ-6582-H Smooth chromed valve cover without "Powered by Ford" embossed in the metal. Correct on 1967 DGS Mercury Cougar and optional on 1965-67 Ford Mustang with 289 engines. Ford master parts catalog shows a right and left version of this cover those numbers are C6ZZ-6582-H & C6ZZ-6582-J. *Note - This is a used chrome valve cover. The plating was pretty low quality back in 1966-67 and these will show rust pitting. For best results we recommend the painted version of this valve cover...

Reproduction set of after market cast aluminum valve covers with COBRA 428 lettering. Fits any FE style Ford engine, including 390, and 428 cubic inches.

New Old Stock passenger side (right hand) vent / wing window handle for the 1967 Mercury Cougar or Ford Mustang. Also fits 1966 Ford and Mercury mid sized cars. Ford part number C6OZ-6222916-A.

Good used axle vent nipple or tube. This vent tube screws into the top of the rear axle and is a breather / vent to equalize the pressure inside the axle tube. Fits both 8 inch and 9 inch rear axles. Fits Mercury Cougar and Ford Mustang 1967-73.  A (5/16" inside diameter) rubber hose about 18-1/4 inches long attaches to the nipple. Has a very tiny diameter hole inside, about 0.062". Needs to be kept clear to work properly. Also see the reproduction version from AMK. Concours hose kit with...

This kit includes 2 vent frames, 2 quarter window frames and all four stainless parts that complete the frames. By purchasing this as a kit you are getting the stainless parts for almost free. Keep in mind, those who send in high quality cores in advance of making their order get the advantage of core matching. If you send in cores in advance with minimal pitting we hand select your parts to give you our best. If you do not send your cores in advance we select your parts randomly. If you are...

Used grade "A" driver side (left hand) vent window frame as it comes out of the door and is just the bare window frame. This is not a perfect part but it will look good on a low mile car that shows a little patina. The weatherstrip track that continues down into the door can be had with this part for no extra charge, please mention it in the comments section when you order online. Ford part # C7ZZ-6522205-A. Casting # C7ZB-6522223-A Check out our video below for helpful tips on disassembling...

New old stock instrument panel voltage regulator or IVR for all 1967-68 Mercury Cougar and Ford Mustang. Additionally fits 1967-68 Ford full size, 1966-68 Torino,CycloneMounts to the rear of the instrument clusters, voltage regulator for dash gauges power.  Ford part number C6DZ-10804-A. Check out the video below on our new gauge tester: ...

This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety standards. The mirror nut tool will fit over the 1967 wand, but not the 1968.

Emergency or parking brake indicator lamp and wiring assembly. Tested and working red indicator light which was found optionally on any 1967 Mercury Cougar standard model 65A or 65C. The 1967 parking brake light kit gets its power from the ignition switch. Ford part number C7WB-10A841-A. This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in...

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

Small block Ford water pump core, suitable for rebuilding. This version has a casting number of C6OE-A. Found on many Ford 289 engines from 1966-67. These do not have casting dates, and plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tubes, and impeller will need replacing. Occasionally they have the original non-HiPo cast iron impeller, but not always. See our other core water pump listings for other casting...

Dated 6M29, December 29, 1966. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two...

Dated 7C17, March 19, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two different...

Dated 7C20, March 20, 1967. Big block Ford water pump core, suitable for rebuilding. This version has a casting number of C6AE-8505-B. Found on many Ford 390 engines from 1966-67. These have casting dates, we list the dates when we have them in stock. Plan on sending it to a vendor that specializes in water pump rebuilding. In all likelihood, the rear cover, heater tube, and impeller will need replacing. See our other core water pump listings for other casting numbers. Two different...

Original NOS part, new in box. Ford part # C5ZZ-6503110-A

Economy replacement vinyl top that looks great and fits perfect. This economy version top has the fuzzy white backing, not common on the more expensive vinyl tops.  Picture demonstrates texture.

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction concours weave black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown...

Reproduction black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown here. ...

Reproduction dark red headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a...

Reproduction white headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group option used a wider...

Good used crank correct for 1967 XR7 or standard models. No obvious blemishes, driver quality. The Ford part # is C5ZZ-6523342-C, casting number as found on the back reads C7ZB-6523348-A. *Customer Feedback* Don, Lin and staff; Just to let you gentlemen know that I have received the 1967 XR7 saddle tan door panels you sent and I am extremely happy with the condition and the service! It has been less than a week since I ordered them and they arrived via USPS, as per requested, with a very...

Good used

Good used

This is a good used fitting with large and small nipples for use with the foot actuated washer pumps found on 1967-68 Mercury Cougar and Ford Mustang. Good used part that we verify the check valve is working. These screw into of the rubber covered pumps.

High quality rubberized vinyl bag, with Gold silk screened FoMoCo logo. An exact copy of the original unit. Only the early model 1967 Cougars would have used this, all other 67-68 Cougars would have used the plastic washer bottle. Replaces Ford Part # C1AZ-17618.According to Phil Parcells who runs the national data base for the Mercury Cougar, the changeover from the washer bag to the plastic bottle was approx Dec 1, 1966, at approximately consecutive unit # 545100. However there are oddball...

1967 was the last year for the 3/8"-16 threads. We also carry the J bolt C6OZ-1448-A, and the top plate or disc C5ZZ-1424-A. Wing-nut, spinner. *NOTE* The original 67 wing nut had no protruding tabs in the recessed area as did most of the 1968 - 1973 wing nuts.

We shatter the castings from used back-up light assemblies to remove the socket and pigtail complete. This is for the person who has a nice original back up light and is willing to invest the time to repair a damaged pigtail. This light was also used on the 1965-1966 Ford Mustang.

Differs from all other Cougar console wiring in that it has a black plug for the shift indicator light.

Factory used and tested under dash wiring harness for all 1968 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This harness plugs into the speaker plug of the radio, and connects the kick panel speakers in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door wiring harness that has the speaker plug for the door mounted speakers in 1969-70 cars. White speaker wire goes to the passenger side speaker, and the orange colored wire...

Quality reproduction of the tilt column wiring harness for the 1967 Mercury Cougar and Ford Mustang. Two harnesses as shown in the wiring diagrams. 

Used under dash wiring harness repair plug and pigtail for the neutral safety switch / back-up lights and engine feed harness for the EARLY 1967 Mercury Cougar. This is part of the 14401 main under dash wiring harness.*NOTE* The blue/red to yellow/black wire is for the radio feed. The only difference between the early and late harnesses, is the early harness has an extra blue wire.

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio. Original used under dash speaker wiring harness pigtail for all 1967-70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your passenger side speaker, which is denoted by the white wire.Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the...

This pigtail is for 68 - 70 cars, but will work on 1967 cars with 8 track radio.Original used under dash speaker wiring harness pigtail for all 1967 - 70 Mercury Cougar and Ford Mustang cars with factory AM/FM or AM 8 Track stereo radios. This speaker wiring harness pigtail plug end goes to the your radio. Part of the stereo speaker wiring harness that goes to a pair of factory speakers in the kick panels in a 1967-68 Mercury Cougar or to the A pillar post where it connects to the door...

Used under dash wiring harness repair pigtail for your Mercury Cougar is from the ignition switch to the harness plug that feeds the regulator, starter solenoid, and alternator. This is part of the 14401 main under dash wiring harness.*NOTE* This pigtail also has a pink resistor wire that should not be cut or spliced because it's ohm resistance is dependent upon it's length.

Used wiring pigtail that runs from the under hood harness to the starter solenoid (battery side post) on the 67 - 68 Standard and XR7 model Cougars.

The Wittek Company manufactured the tower clamps used on the Cougar from 1967 to 1973, the Mustang from 1964 1/2 to 1973, as well as many other Ford and Mercury cars during that period. In October or 1993, the company filed for bankruptcy. This has made the tower clamp unavailable to the classic car restorer. Our supplier was able to bid at the auction for enough of the original tooling and parts to make these clamps available again. Other companies have also reproduced these clamps, but...

New old stock manual steering worm gear for any 1967-70 Mercury Cougar or Ford Mustang with manual steering or 19:1 steering gear box. Factory new worm gear assembly for rebuilding your steering gear box. NOS in the box Ford part number C7ZZ-3524-C. Check out this video

Used wrench or crank, for manually closing the factory installed sunroof installed on any 1967-73 Mercury Cougar. Sunroofs, technically moonroofs, were originally installed by ASC or American Sunroof Corporation. Hertz 1968 XR7-G cars all came with factory sunroofs, as did the Hertz rental 1969-70 Cougar Eliminators. ASC also installed sunroofs in Ford Thunderbird, Lincoln MK III.ASC used Golde mechanical parts from Germany. Golde was a manufacturer of sliding canvas and metal roofs on...

[No Description Provided]