Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1-48 of 193
$0 Price: $45.45

Buy Details

Availability: In-Stock Item
Item #: 14-0024 -

New adhesive / epoxy applicator to apply our 3M window adhesive to the glass (or whatever else needs bonding) in your Mercury or Ford. This non-drip unit features an easy loading breech, a 1:1 mixing ratio and full cartridge support. We also offer a 60 day loaner if you only need this unit for a short time. ...

$0 Price: $79.96

Buy Details

Availability: Out of Stock, On Order
Item #: 10487 -

This high performance alignment kit replaces the factory eccentric bolt and cam that holds the lower control arm to the frame. The eccentric cam is used for setting wheel camber. When the eccentric is turned, the lower arm moves in or out changing camber. Stock eccentric cams can slip or rotate going over bumps, allowing the alignment to change. Which is the cause of many worn tires. The lower control arm adjusting cam eliminator kit replaces the eccentric bolt and cam with non slipping...

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24393 -

C8OA-3B236-A Complete lower control arm cam and attaching bolt. 4 pieces included - Cam/bolt, lower cam, nut and lock washer. We offer this used front suspension lower control arm adjusting cam from rust free Western States cars. These are MUCH better quality than any of the stock "looking" reproductions offered. For use on all 1967 - 1973 Mercury Cougar and Ford Mustangs. Part of the C6OZ-3048-A lower arm mounting kit. Bolt/cam part number C8OA-3B236-A, secondary cam part...

$0 Price: $1.45

Buy Details

Availability: In-Stock Item
Item #: 41430 -

Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.

$0 Price: $99.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24630 -

Left side axle, 28 spline 27-1/16 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs.*Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

$0 Price: $139.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24629 -

Right side axle, 28 spline 31-1/8 inch length. For both 8 inch and 9 inch rear ends. Ships with used bearing, bearing retainer plate, and 5 pressed in wheel studs. *Note Boss 302 and 428 CJ equipped Cougars came with heavy duty 31 splined axles.

$0 Price: $199.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27516 -

Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare 8 inch axle housing with proper axle pad spacing, vent location, brake line attaching, and fill plug in third member. Over-sized shipping length.

$0 Price: $225.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24271 -

Bare housing with proper axle pad spacing for all 1967-1968 Cougars with 289 or 302 engines. Over-sized shipping length. Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. This axle housing was used starting about mid 1967. It does not have the fill plug in the rear of the housing. * Important - Please check your car to verify that your 8 inch third member has a fill plug. Replaces Ford part number C7ZZ-4010-E. ...

$0 Price: $399.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27514 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Spring perches are 43 inches apart on center. Complete rear end housing - drum to drum, with axles, and with pumpkin. 1967 EARLY 8 inch rear end housings with fill plug in the steel housing as seen...

$0 Price: $445.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24269 -

NOTE! When we ship a rear end, we will remove the third member and ship it in a separate box. Some assembly will be required. Housing overall width - 54-1/4 inches flange to flange without fill plug in housing. Spring perches are 43 inches apart on center. Overall width measured from faces of axles, not the tips. All 1967-70 have the same overall width of 59-1/2 inches. Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long. Complete rear end housing - drum to drum, with...

$0 Price: $929.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24270 -

Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Bare 9 inch axle housing with proper axle pad spacing, vent location, brake line attaching, and rear fill plug. Correct for all early 1967 big block Cougars. Over-sized shipping length.Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long.

$0 Price: $1,000.04

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27515 -

Housing overall width - 54-1/4 inches flange to flange. Spring perches are 43 inches apart on center. Axles used: Passenger side - 31-1/8 inches long, Driver side 27 inches long. Bare housing with proper axle pad spacing, vent location, and brake line attaching. For all 1967 late big block Cougars and 1967 Mustang GT. Over-sized shipping length. This is the late 1967 housing that incorporates the oil fill plug in the third member or pumpkin. *Tip* If you are looking to strengthen your 1967-68...

$0 Price: $32.75

Buy Details

Availability: In-Stock Item
Item #: 15819 -

This is the 4 hole version of the ball joint for the 1967 - 1969 Cougar and Mustang. Right is same as left. Two required per car. Hardware included.

$0 Price: $54.64

Buy Details

Availability: In-Stock Item
Item #: 13000 -

New axle bearing for any 8 or 9 inch Ford rear end with 28 splined axles. Common on all Mercury Cougar and Ford Mustang with V-8 engines. Excludes 31 splined axles as found on Boss and Cobra Jet cars.These should be professionally installed with a bearing press.

$0 Price: $9.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11371 -

Used front crossmember bolt for the Mercury Cougar or Ford Mustang. It is crucial that you use this correct tapered bolt when installing the front cross member.

$0 Price: $13.45

Buy Details

Availability: In-Stock Item
Item #: 32154 -

Bolt kit for installing front sway bar clamps to the body for any 1967-68 Mercury Cougar or Ford Mustang. 3/8" bolts for 1967-68 cars. Starting in 1969, the bolt size was changed to 5/16". This size of bolt is obviously stronger and can be used on all cars 1967-73. 

$0 Price: $144.85

Buy Details

Availability: Out of Stock
Item #: 23883 -

Bracket mounts to 9 inch third member. Will not have heavy corrosion as found on Midwest and Eastern cars. Not notched like later years of snubbers. Correct for 1967 Mercury Cougar and 1965-67 Ford Mustang. Rubber bumper sold separately - C3AZ-4730-B rubber carrier bumper. Picture - 2007 40th Anniversary show in Carlisle PA. Bill Pratt with "Catvert".

$0 Price: $6.15

Buy Details

Availability: In-Stock Item
Item #: 26561 -

Mounts to the bottom lip of the coil spring cover, two required per car, sold individually. Replaces Ford part #: C6OZ-3020-A.

$0 Price: $7.35

Buy Details

Availability: In-Stock Item
Item #: 26525 -

Mounts on floor pan above the center of the rear axle over 3rd member on small block cars with 8 inch rear ends. Mustang only, will not fit a Cougar.Replaces Ford part #: C5ZZ-4730-B orC3AZ-4730-B. Customer Comment:Thank You Don and WCCC,Copy Cat's almost done!Yesterday was such a nice day I took Copy Cat out to Show Don and Lin the final (almost) product.Without their patience and understanding along with a great selection of parts I wouldn't have her in such great shape.Thanks guys, along...

$0 Price: $1.36

Buy Details

Availability: In-Stock Item
Item #: 41270 -

This is the bushing that Ford lists as the REAR stabilizer end link bushing, but it works for both front and rear. Smaller image shows a comparison of the NOS(Left) and Repro (right). SOLD INDIVIDUALLY. Replaces Ford Part #: KC-55490-A.

$0 Price: $30.35

Buy Details

Availability: In-Stock Item
Item #: 26724 -

Although this premium reproduction strut rod bushing kit appears very similar to the economy kit, they are in fact superior. The main difference being that the bushings are made from a higher quality rubber compound.Replaces Ford Part #: C6OZ-3A187-AR.

$0 Price: $34.97

Buy Details

Availability: In-Stock Item
Item #: 14060 -

These are OEM replacement bushings. The problem with these are most original sets are rusted out on the metal parts. We highly recommend the upgrade, unitized sets we sell over the orignal design.Replaces Ford Part #: C6OZ-3A187-A

$20.00 Price: $27.35

Buy Details

Availability: In-Stock Item
Item #: 13373 -

It took a long time but our supplier finally got this bushing right. They ended up copying a never installed production original bushing Ed Meyer acquired from the Kar Kraft factory back in the day. All details have been copied including the two small ribbed lines located on one side. NOS Bushing notes: If you have NOS C9ZZ-5493-A front sway bar bushings in a Ford bag good luck making them fit. Yes, its a documented fact that almost all NOS 15/16" sway bar bushing Ford sold in a bag are too...

$0 Price: $3.35

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27504 -

Used 3/8-16 x 41/64"  carriage bolt for the shock tower shock cap. Three bolts used on each cap, 6 total per car. Sold individually. *Note - Carriage bolt detail cleaned for the picture, actual part will need a clean up on a wire wheel.Replaces Ford part number 378535-S2.

$0 Price: $134.01

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12379 -

We will loan this coil spring compressor for 60 days, with a 100% refundable purchase price. This tool now comes with a bearing to make the job much easier. Only available to customers that purchase our front suspension rebuild kits. Tool must be returned in undamaged condition with no missing parts within the 60 day time period. Returns past 60 days are subject to a 25% restocking fee. Coil spring compressing tool, this is a must for safely removing front coil springs on any 1967-73...

$0 Price: $139.85

Buy Details

Availability: In-Stock Item
Item #: 12-3009 -

New coil spring compressing tool to compress the coil springs of the 1967-73 Mercury Cougar or 1965-73 Ford Mustang. This tool now comes with a bearing to make the job much easier. This spring compressor is a must for safely removing front coil springs. We also offer a 60 Day Loaner if you only need the tool for a short period of time. *NOTE* Not recommended for heavy duty coil springs like found on pickup trucks and full sized cars. ...

$0 Price: $9.75

Buy Details

Availability: In-Stock Item
Item #: 31550 -

Made from polyurethane, a bit more rigid and stiffer than our rubber insulators. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. Replaces Ford Part #: C4DZ-5415-A.

$0 Price: $5.27

Buy Details

Availability: In-Stock Item
Item #: 26654 -

Made from soft flexible rubber very similar to the OEM material. Sold individually. Two required per vehicle. These are the coil spring insulators available from most Mustang/Cougar suppliers. If you prefer polyurethane insulators, you can find them here. Replaces Ford Part #: C4DZ-5415-A.

$0 Price: $38.75

Buy Details

Availability: In-Stock Item
Item #: 26684 -

Features quality stamped steel construction, bushings, nuts, anti-squeak coil protector pads. From the get go these were never a very good design... The rubber is prone to cracking and the unit will bind under severe use. Not just speaking of the unit we are offering but all of them including the original Ford units. Here is an interesting article for those that are not happy with status quo. Global West and others have come up with their own solutions and after we have spent more time testing...

$0 Price: $84.05

Buy Details

Availability: In-Stock Item
Item #: 11979 -

High Performance Coil Spring Perches offer a very affordable upgrade to stock spring perches with rubber bushings. These are made with synthetic elastomer bushings which are similar to polyurethane in performance and longevity, but will not squeak like polyurethane. The perch can rotate 360 degrees on the shaft, which allows the front suspension to articulate freely. This feature also eases the installation of the coil spring. Zerk grease fittings are installed and locking nuts are included....

$0 Price: $140.20

Buy Details

Availability: In-Stock Item
Item #: 26688 -

These Linear springs are custom wound for the performance-oriented customer. These feature 600-pound/inch rating and will lower the car approximately one inch from stock. Painted black, sold as a pair. Note: If you look close at factory sales pictures from the day you will notice the cars sit about 1" lower in back than front. These springs will level the car out provided your rear leaf springs are not sagging.  Linear springs are the easiest to understand. When you think of a spring,...

$0 Price: $226.25

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 11688 -

Get ready for some serious labor if your car needs this complete panel!

$0 Price: $46.67

Buy Details

Availability: In-Stock Item
Item #: 25963 -

This kit is good for cowls with moderate to minimal rust. Easy to install on the driver side, but takes more effort on the passenger side especially if you have A/C. Another way to avoid doing expensive cowl repairs is to purchase our cowl cover.

$0 Price: $109.15

Buy Details

Availability: In-Stock Item
Item #: 17-0002 -

This original part has been reinforced to brace the front frame rails / tie together lower control arm pivots in a superior way to the original design. This design will prevent any camber change in hard cornering. This is not needed for the average Cougar owner but if you are desiring to make your car a "Handling Machine" every bit counts and this is an inexpensive upgrade. These crossmembers are welded in house, and will be unpainted bare metal. This combined with our shock tower...

$65.00 Price: $69.15

Buy Details

Availability: Out of Stock
Item #: 11372 -

This product has received the 'Crappy Product' certificate. Items that receive the 'Crappy Product' certificate are products that we carry for comparison purposes as they are often the version offered by other vendors or because it is the only version available. We would not be willing to use these parts on our own cars, and we do not recommend purchasing these parts. WE ARE NOT ABLE TO ACCEPT RETURNS FOR THESE PARTS. This is the reproduction cross member offered by most of the Mustang...

$0 Price: $29.57

Buy Details

Availability: Out of Stock
Item #: 11383 -

This reproduction radiator support crossmember is correct for the 1967-68 Mercury Cougar and Ford Mustang, but will work on any 1967-70 Cat or Pony.Replaces Ford # C7ZZ-6510852-B or C9ZZ-6510852.

$0 Price: $963.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 19926 -

1967 Front unibody cut, this one has only one torque box which is located on the driver side of the car. If originality isn't an issue we recommend 1968 versions that have both torque boxes, which adds strength. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual...

$0 Price: $963.86

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27222 -

1967 Front unibody cut, this one has only one torque box which is located on the driver side of the car. If originality isn't an issue we recommend 1968 versions that have both torque boxes, which adds strength. Excellent value! Please consider a front clip replacement for your vintage 1967-73 Cougar or Mustang - including fastbacks! No differences exist between the front understructures of a Mercury Cougar or Ford Mustang year for year. How many hours of labor is needed to replace individual...

$0 Price: $743.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 20184 -

Comes with good shock towers, front aprons, and core support. This is a great value for those that need to replace multiple parts upfront as you will not only get factory joined parts that will save you money and time, but it will also  preserve the value of your car. With a clean Western cut like this, one should be able to install it so that nobody would ever know your car has had anything replaced. You will have to call to order this one. Expect to pay about $300 for crating and...

$0 Price: $1,499.85

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 20509 -

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new 4 pinion Trac-Loc unit, new Motive ring and pinion gears, new Timkin bearings, new crush sleeve, new bolts, and new seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. There are various ring and pinion (gear) ratios and axle splines available, if you are unsure of what you need it is best to call (503) 463-1130 for your order. This is a drop ship item. *Note - New...

$0 Price: $1,999.89

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 20510 -

Limited slip 8 inch Ford third member rebuilt with all new parts. Factory new Eaton True-Trac 8 pinion clutchless traction locking unit, Richmond ring and pinion gear, Timkin bearings, crush sleeve, bolts, and seal. Rebuilt using 1967 and newer two rib style case, with oil fill plug, and standard 1310 yoke. Ships with direction sheet and bottle of Ford Motorcraft friction modifier additive for the rear end gear oil. For use with 28 splined axles, but can be custom...

$0 Price: $2,381.85

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 19797 -

Limited slip, nodular 9 inch Ford third member rebuilt with all new or reconditioned parts. Used modern design Detroit Locker unit, new Richmond ring and pinion gear, new Timkin bearings, new selective size sleeve, new bolts, and new seal. Rebuilt using 1967-1973 nodular 9 inch cases with oil fill plug, for 28 or 31 splined axles. This unit was used in 1967-73 Cougars and Mustangs, but it also came in any other Fords or Mercurys with a 9 inch drop out center section....

  • < Prev