Interior

Due to time constraints, we can no longer offer the service of having your own mirror restored, this is now an exchange based service only.Any mention of it in the video below is outdated, please disregard. Restored 1967 early style larger rectangular rear view mirror lens for the Mercury Cougar or Ford Mustang. Unlike our full price restored lenses, these require no core. These lenses look good at first, but if you look close you may see a scratch, tiny chip around the perimeter or...

Identified with the straight bracket compared to the 1968 relay which has a bend. Keep in mind we have a reproduction substitution for this part. Ford part # C7ZA-3E553-A. Ford packaging reads C7ZZ-10B926-A *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. Helpful tip:  For those having trouble getting their tilt away mechanism to...

This fits behind the door panel and is needed to install your remote mirror correctly.*NOTE*1969 Cougar owners do not need this part as it is built in the the chromed plastic, rectangular bezel on the door panel.

Replaces Ford Part #: C0AB-6423240-B. Four required per car, two per side. If your quarter glass is loose in the track and will not roll up and down these rollers are most likely the culprit. When the tracks get gummed up and the window takes too much effort to roll up and down, these brittle old rollers will break. Even if they are not broken they are often frozen in place from rust and will not spin freely. From our experience every 1967 - 1968 Cougar needs these replaced if they still have...

Sold individually, original glove box cable screw with shoulder. For any 1967-70 Mercury Cougar or Ford Mustang. Probably many other Ford and Mercury cars also.Ford part number 379202-S2.

Used in the latter part of 1967 and all of 1968 and 1969 to fasten the upper column cover to the column. Early 1967 used a chrome version of this screw.

These are original looking seat belts at affordable prices. These are not Concours reproductions, but have the correct vintage look used by Ford on several cars in the Mid to Late 1960's. Starburst Medallion used on the buckle is an exact copy of originals. Hardware included!Sold individually

Now you can replace this original part, which is commonly stripped out, with a nice reproduction. Must be welded to floor pan. 6 total per car, 2 inboard in the transmission tunnel, and 4 on the rear seat pans. The front outboard anchors are part of the rocker rails. Rectangular shaped like the 1967-73 cars. We have noticed that the last generation 1971-73 Cougars had 4 round shaped plates in the rear floors. Same threads, all work the same. These were pretty much used on all Ford...

This is a 100% complete, functional set taken from multiple 1967 Mercury Cougars. Often it takes 2-3 cars to put together one set, decent driver quality set as the driver side will often show excessive wear and other belts can be rusted or missing. The set has been thoroughly inspected, cleaned and redyed with RIT dye in a boiling vat with vinegar. This set is driver quality and if one looks closely you will probably find a small crack in each of the re-tractor plastic covers, a few dots of...

This dealer option was installed for people who were not comfortable with the height of their seats. This same kit was used on many intermediate Ford Products from 1965-1970. One kit does one bucket seat or one bench seat. Ford part # C6OZ-6362016-A. Click on images to enlarge. The screw on clips were included in the kit so the spacer would stay in place as the seat was guided into the four holes in the seat riser. Often these clips are cracked or missing and we cannot guarantee all four will...

Used driver side outer bucket seat black hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561695.

Used driver side outer bucket seat SADDLE hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561695.

Used AQUA passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer plastic...

Used IVY GOLD passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer...

Used SADDLE passenger side inner bucket seat black hinge cover, for any 1967 Mercury Cougar or Ford Mustang. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. Limited to supply on hand. Additionally, this will also fit the driver side outer on 1967 Ford Mustang. Reproduction is available, and these can be installed on the driver side outer of a 1967 Mercury Cougar. But they did come with a longer plastic...

Used passenger side outer bucket seat black hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Used passenger side outer bucket seat IVY GOLD hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Used passenger side outer bucket seat red hinge cover, for any 1967 Mercury Cougar. This is for only a single hinge cover in used condition. Most will have minor scuffs or imperfections. These do not accept paint very well. The factory did modify these by trimming the end that goes under the upholstery. What we have in stock is what we have, some trimmed, some not. Limited to supply on hand. Ford number C7WB-6561694.

Reproduction chrome knob for the seat track release to adjust the position of the seat. This knob is an exact replica of the original and installs with a hidden set screw. A simple way to dress up your interior while maintaining a stock appearance. Made from chrome plated die cast metal.Sold individually. Replaces Ford Part #: C5AZ-6261753-BA.

We have a VERY limited supply of seat tracks that are taken from cars that have never been in the weather. These should need nothing but cleaning and lubrication. Fits all 1967-70 Mercury Cougar including convertible, and 1965-70 Ford Mustang. Used kit includes C5ZZ-6561704-F, C5ZZ-6561705-F, and C5ZZ-6561726-A. Note that many of the 67's do not have the rectangular plate in place as seen here. We have a separate listing for those if you want to match your existing version. ...

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Ford master part number C7ZZ-6561705-A. Application 1967-69 Mercury Cougar and Ford Mustang only.

Good used part that will need to be cleaned up and painted if you want it to look perfect but will be ready to use as is. Functionally and structurally perfect, cosmetically average. Clean original FoMoCo parts like these in the end are almost always a better choice in the end even if they do require some elbow grease to look as new. There are minor differences between the years, select the correct year for your application and we will be sure to choose the correct style from our large...

Installs between seat track and carpet. These are the same gauge steel as originals. Four per bucket seat, normally only seen on the 1967 model year, will need to be restored. Reproductions work fine, but look a little different. Ford Part # C5ZZ-13190-K

1967-69 Mercury Cougar and 1965 - 1969 Ford Mustang shifter handle for automatic transmissions. We find this smaller early style chromed shifter handle in lots of 1969 Cougars, we believe that there was a transition period before the C8OZ-7213-A was used. This is the base model shifter handle with both black buttons, and set screws. Ford part numbers C5ZZ-7213-F, C5ZZ-7C488-M, C5ZZ-7C488-D. Click on images to enlarge. Check out our video on rebuilding your shifter below: ...

New old stock 1968-72 (works on 1967) Mercury Cougar XR7 and Ford Mustang Deluxe shifter button for automatic transmissions. This is for all cars with body type 65B, 76B, and Grande. This is for the deluxe model shifter. New old stock, NOS. Ford part number C8OZ-7C488-A. Check out our video on rebuilding your shifter below: ...

Brass sensor that screws into intake manifold and activates temperature gauge in dash. Replaces Ford Part #: C6DZ-10884-B (SW-552) or C9WY-10884-A (SW-888)*. Temp Sender Switch Temp Rating : 15.2-19 Ohms Resistance At 220 Deg F Temperature Switch Thread Size : 3/8" x 18 NPT * - The 1969 351 Windsor temperature sending unit has been discontinued. Most manufacturers list the 1968 302 temperature sending unit as the closest replacement.Check out the video below on our new gauge tester: ...

Mercury Cougar shift handles never came covered in real leather from the factory but what a cool upgrade! We sell a lot of these and the feedback has been great. We also carry the original plastic covered (simulated leather) reproduction XR7 shift handles in several colors but this real leather handle comes in black only.

Complete floor shift assembly for the 67 - 68 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm. Ford part numbers: C7ZZ-7210A C7ZZ-7A306B C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

If you want to install factory shoulder belts on your 1967 Cougar or Mustang, you need to install these shoulder belt brackets. It's a threaded block inserted into the clip that holds it in place. 67 Cougars and Mustangs didn't come with shoulder belts, but the raised area where these brackets attach is still present. Simply clip the bracket in place. Now you've got what you need to bolt that shoulder belt in place. Keep in mind that you need to have the correct lap belt configuration to be...

Attaches to the console shifter bezel on any 1967-68 Mercury Cougar or Ford Mustang. We occasionally have these available when we get broken console bezels. This surround or "U" plate was originally attached with heat to pin connectors. To reattach we suggest using glue. This U part attaches to the bottom of the console shifter bezel and shrouds the light. Check out our video on rebuilding your shifter below: ...

This reproduction cigar / cigarette lighter socket is a good fit and is easy to install. This lighter socket also comes with the retainer. Replaces Ford part # C6ZZ-15055-B.

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Used steering wheel tension spring used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. Keeps tension on the steering wheel shaft so as to keep the steering wheel from contacting the upper column cover. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. NOS new old stock door jamb switch to release tilt/tilt-away columns on a 67, 68 or 69 Mercury Cougar or Ford Mustang. Here is an excerpt from the 1967 owners manual: The wheel will swing to the right and up towards the instrument panel whenever the driver opens his door, provided the ignition switch is turned off. When re-entering the vehicle on the drivers side, pull the...

The classic hood mounted tach from the 60's. Black plastic housing with a black or white dial face and bright back lit numbers makes this a great add-on accessory. Features a red-line needle. Holes must be drilled in the hood for proper installation.  It measures 5 1/4" at its widest, 3 1/4" at its tallest and 9" long when you include the hooded portion. Installation:   Wires: Red – Power Black – Ground Green – Coil – Negative White – Lights Internal switch which can be viewed...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels on any 1967-70 Mercury Cougar or Ford Mustang. Additionally, it also removes the wiper switch on 1969-70 Mercury Cougar and Ford Mustang. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68, or 1969...

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. We also have a handmade version of this same tool for a lower price.

Great investment considering how easy it is to mar your switch, bezel or dash paint when trying to remove your ignition switch bezel with a hammer and screw driver. Black, basic handle tool removes and installs headlight switch bezels. When coupled with ignition bezel tool it removes and installs ignition switch bezels on any 1967-68 Mercury Cougar and Ford Mustang. A 5/32" Allen wrench is needed to attach tools together. Allen wrench included.  ...

One required per car, includes Phillips screw.*NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. ...

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used vacuum reservoir for the tilt / tilt away steering column equipped Mercury Cougar or Ford Mustang. This is a 1967 only design that is very hard to find in rust free condition with a working vacuum check valve. Beware of substitutes as there are close facsimiles with different sized nipples, different brackets or plastic built in check valves. These versions off later model cars...

New Old Stock passenger side (right hand) vent / wing window handle for the 1967 Mercury Cougar or Ford Mustang. Also fits 1966 Ford and Mercury mid sized cars. Ford part number C6OZ-6222916-A.

This threaded replacement wand will require you to cut 8/32" fine threads in your original controller. Your OEM mirror controller is made of a very soft metal so one can often install these as "self tapping".1967 and 1968 are different, see comparison picture. The 1968 version was rounded off due to new safety standards. The mirror nut tool will fit over the 1967 wand, but not the 1968.

Used seat belt bolt washer for the Mercury or Ford.

Used on front re-tractors, two per side on either side of the re-tractor mounting hole. Used to prevent rattles.

Reproduction Concours weave black headliner windlace for the driver or passenger side of the Mercury Cougar or Ford Mustang. This unit helps hold the sides of the headliner in place and covers the pinch weld; it is also known as the pinch weld moulding. This is an individual piece and is 7 feet of windlace. You will have to trim this piece to fit and it should be around 6ft each when correctly trimmed. This windlace is correct for 1967-70, however the 1967-68 Cougar with the décor group...

Reproduction concours weave black rear interior panel windlace that helps hold the rear interior panels in place. It is also known as the pinch weld moulding. This one piece of windlace will fit on either the driver and passenger side and is about 2 total feet worth of windlace. You will have to trim this unit to fit and it should be about 20 inches when correctly trimmed. *NOTE* There are two types of this trim found in the 1967-68, the smooth or rough textured version like the one shown...