Interior

Reproduction Sun Visor Bracket & Rod for the 1967, 1968, 1969 and 1970 Mercury Cougar or Ford Mustang. Great quality and fit, left and right use same part, sold separately. Replaces Ford part # C7AZ-6204144-A.

Used cigar / cigarette lighter and ashtray mounting bracket. Mounts behind the dash on 1967-68 Mercury Cougar and Ford Mustang. Holds the cigar or cigarette lighter element, and the ashtray receptacle. 

These courtesy light brackets are located on the very outer right and left under the dash. Typically this bracket is found on the passenger side of 1967-68 Mercury Cougar and Ford Mustang without air conditioning. This is the long style bracket. There is also a short style for both the driver and passenger side courtesy light. If you have factory air conditioning you would want the short bracket that doesn't come into contact with the A/C plenum.Replaces Ford part number C7ZB-13763-A.Fits:1967...

Lower steering column mounting bracket. 1967-68 Mercury Cougar and Ford Mustang. Right and left halves with original fasteners. Rubber gasket sold separately.Ford part number C7ZZ-65017A50 and C7ZZ-65017A51.

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Used bracket for the vacuum reservoir for the tilt / tilt away steering column found in the Mercury cougar or Ford Mustang. This specialized little bracket is used to mount the tilt / tilt away vacuum reservoir in place. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most columns with serious problems do need complete tear down and build up which usually takes 3-4 hours plus the cost of any replacement...

Used windshield wiper mounting bracket for any 1967-68 Mercury Cougar or Ford Mustang. Part of the wiper motor assembly in the Master Parts Catalog, so no Ford number found.

Unique to power brakes and only with 1967 Cougar steering columns. Pedal shipped bare, picture may show hardware and pedal pad with trim. *Note* You will have to drill holes in your existing pedal hanger to accommodate the power brake pedal. Since systems with a vacuum booster take less effort to activate than systems without, a different folcrum point is used that does not utilize built in bushings into the hanger. Please refer to our power brake pedal hanger listing for measurements on where...

These often missing parts are glued into the two recessed areas designed to hold the female portion of your lap belt. They prevent wear on your buckles and keep them from rattling if you are one to leave the shoulder harness off. Sold individually, 2 required per car. There are at least two different styles of these, one version has a ridge near the top. Either one may be shipped.Ford part number C7ZZ-65044E16-A. ...

Sold as a pair. Two required per car.Replaces Ford Part #: 380239.

Replacement rubber bushing for repairing any automatic shift arms on any 1967-73 Mercury Cougar or Ford Mustang, and most Fords with automatic floor shift levers. Fits arms with 3/4 inch lower holes for attaching transmission shift rods. Replaces Ford part number C7ZZ-7343 Check out our video on rebuilding your shifter below: ...

This is the longer of the two versions found on the 1967 XR7 and also found on the Shelby and Mustang. The lens used with this reset button has a smaller hole than the 1968 version.

Great Reproduction of an Often Broken Part. This part fits on the bottom of the steering wheel and must be in place to cancel your turn signal on tilt column cars. Used on all Ford products with a tilt column 1967-69. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here...

Factory original turn signal canceling cam. Originals were molded in white, reproductions are molded in black. Repros also available from us. Without this part that self attaches to the back of your factory steering wheel, you will be turning off your blinkers manually. Click up, click down... *NOTE* We have no good reason to encourage you to purchase this hard to find original over the reproduction, unless you just gotta have it. **NOTE** Need help diagnosing a Cougar turn signal problem?...

Used cap for the index lever tension spring for the Mercury Cougar or Ford Mustang equipped with the tilt/tilt away steering column. Two required per car.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Usually ships in 3-5 business days. Supplier is backordered on this product. Items may not ship until Feb 2023. This is a reproduction of the automatic transmission console for a 1967 Mustang but it also works on a 1968 Mustang. With the the addition of the two pads (Radio Pad and the Lower Pad: 1967 or 1968) it easily becomes a 1967 Cougar or 1968 Cougar console. ...

Usually ships in 3-5 business days. This is a 3 or 4 speed console for a 1967 Mustang but with the the addition of the two pads it easily becomes a Cougar console. Although not visually correct, it will work just as well in a 1968 Mustang or Cougar. Click on images to enlarge. This console does not include the rear radio to console three piece bracket or the windlace that fits between lower dash and console base. The pictures here show the biggest downfall of this console. Right out of the box...

Sprayed with black flocking on the front side and color coded to the console base on the rear side. We have several colors in stock but cannot guarantee you will get your desired color. Will have at least one broken tab for mounting. A drop or two of glue will be needed to attach to the console.

Reproduction center console back plate, or divider, for the 1967 - 1968 Cougar or Mustang center console. includes Light.Replaces Ford part number C3SZ-14A163-B

Call 503-463-1130 for your needs. Many different console bases depended upon year, with or without air conditioning, automatic or manual transmission, XR7 or Standard, and don't forget color.If all we have done is confuse you on what the many differences are and which base you need for your 1967 - 1968 Cougar, this listing may help. Just choose which of the 14 configurations you need. All of our 50 year old bases have some amount of cracks, chips or extra holes drilled. Please contact us...

In the form that is shown, the application for this plastic base is for a non AC car with an automatic transmission. It can easily be cut for an A/C equipped car or a manual transmission, we offer the modification at no cost.  This base is designed for a 1967 standard with AT model but with slight modifications it will work on all models 67-68 manual and AT transmission vehicles. Made from modern injection molded plastic, you will find this is a very sturdy base and the textured...

Good used base with no visible cracks, burns or extra holes drilled. The Cougars equipped with air conditioning had the last few inches trimmed off. It is a rather rough, hand cut from the factory. Standard is different from XR7 in that the XR7 had two holes drilled in the base towards the back to fasten the top pad. The standard base has no metal clip on the top side, midway as the chrome shifter bezel clips into the larger chrome bezel under the top pad. *NOTE* The base shown has been cut...

Good used base with minimal cracks. The Cougars equipped with air conditioning had the last few inches trimmed off. It is a rather rough, hand cut from the factory. Standard is different from XR7 in that the XR7 had two holes drilled in the base towards the back to fasten the top pad. The standard base has no metal clip on the top side, midway as the chrome shifter bezel clips into the larger chrome bezel under the top pad. All of our 50 year old bases have some amount of cracks, chips or...

This listing includes all parts shown here. It is correct for a 1967 Mustang but for those 1967 Cougar owners looking to delete the tired, warped, peeling old pads this is a great way to clean up a very focal part in your interior. These items can also replace the very hard to find 1968 console parts found in both the Mustang and Cougar but look much different than the 1968 style. Keep in mind West Coast Classic Cougar will take your Grade A 1967 or 1968 used console parts in trade. ...

Two required per car, early 67 used a chrome version of this screw. Later years used this screw.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Knob is exact replacement, element is a generic replacement. Exact replacement for 67-68 dash or 69 center console lighter and lighter socket.

Cigar lighter for all 1967-68 Mercury Cougar and Ford Mustang dash ashtray mounted locations. Additionally used on 1969 Cougar and Mustang consoles, console only, not the under dash ashtray unit.

Knob is exact replacement, element is a generic replacement. Socket and element are manufactured by the same company to insure fit. Exact replacement for 1967-68 dash or 1969-70 under dash lighter and lighter socket. Replaces Ford part # C7ZZ-15052 and C6ZZ-15055-B.*Note - Retainer should have a ground lug on it in order to work with 1969 console cigar or cigarette lighters.

This unique little clip looks a lot like the more common door panel clip but on close inspection you will find it is different. Whereas there are slots for three of these per side, only two per side were installed at the factory.Replaces Ford part number 352775-S100.

Used retaining clip for the adjustment bar in the tilt / tilt away steering column in the Mercury Cougar or Ford Mustang. Two required per car, used to hold the tilt position adjustment bar in place.  * While not technically correct, this also will work for 1970 - 1974 Cougar/ Mustang tilt columns. SOLD INDIVIDUALLY*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our...

Used clip for the adjustment tension spring for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

These original clips hold better than the reproductions we offer. If you look closely you will see the angle bend is more acute on the originals. For you 71-73 owners with warped panels you will want to use these original clips (at least along the bottom edge) for a tighter hold. The only difference between this spring clip and the other used one we offer is the presence of the foam spacer pad. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Package of 100 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

Package of 30 spring clips. These are also used to fasten your pads to the console on 1967-68 Models. Coated to prevent rust. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle.

In addition to fastening your door panels to the doors, these spring clips are also used to fasten your pads to the console on 67 - 68 models and seat backs to seats 67 - 70. Coated to prevent rust. Sold Individually. These do not hold as well as our originals but do function fine for most applications. 23 - 29 used per door panel, depending upon model. Helpful tip: Door panel clips install sliding toward the rear of the vehicle. ...

Secures cable to heater control assembly, heater plenum and heater box. Black oxide bracket with screw.Replaces Ford part number 378897-S

Fits 1967 and 1968 Standard or XR7

Prepare to be disappointed... This is a reproduction 1967 - 1968 Ford Mustang clock knob and set screw (replaces Ford part # C7ZZ-15032-A) that can be cut down to work on your 67-68 standard Mercury Cougar (barely). The pictures below will guide you on this "adequate at best" solution for those of you missing this hard to find knob and set screw.Click on images to enlarge. The above picture is a good used original Cougar knob mounted on a 68 clock.  We do not have these original Cougar...

This reproduction stainless trim mounts over your pedal pad. Not only adds style but also holds your pad in place. Replaces Ford part number C5ZZ-7B544-A.

Sold as pair, exact copy. These also double to keep your windlace firmly in place.

One year only part not found on any other car except Cougar and Mustang with tilt. If you would like to run a 1968 or newer steering wheel on your 1967 then you need to exchange this cover with the version found on the 1967 Thunderbird which has no lip at the top. We have these in stock and would enthusiastically trade it for the Cougar / Mustang upper cover. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

This Thunderbird collar is a good substitute for those wanting to put an after-market or 1968 up steering wheel on their 1967 Cougar / Mustang. We also suggest purchasing this collar when installing our reproduction 1967 Mustang deluxe steering wheel.  *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction Console Ashtray Bumper for the 1967 Mercury Cougar or Ford Mustang.

New chrome finish screws for attaching OEM consoles. Screws fit all stock consoles 1967-73 on Mercury Cougar and Ford Mustang, most any Ford consoles actually. Phillips head oval. 1967-68 consoles use 4 attaching screws, 1969-70 consoles need 6 along the outside, 1971-73 consoles have a total of 8 screws along the outside. These are 1-1/2 inches long like the originals.

Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull.  We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...

Used pivot cover for the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction headlight knob, retainer & bezel, cigar lighter and ignition switch retainer.

Used metal dash support brace for all 1967-68 Mercury Cougar and Ford Mustangs. Fastens to the lower flange of the metal dash panel and attaches to the inner cowl, 8-1/2 inches long. Viewed in the 1967 Osborn Body Assembly Manual on page 23. Replaces Ford part numbers C7ZB-6504672 or C7ZZ-6504672-A.