Interior

This light was used on 1967 - 1968 Mercury Cougar and 1967-68 Ford Mustang Consoles with the roll up door. Not for use on the XR7 console. Notice the light lens is painted white on one half unlike the reproduction lens that is all white.  Assembly will not come with a working bulb, you can find the correct 1891 replacement here, or grab an 1891 LED here. You can find a replacement lens here. ...

Original good used part with no cracks, but may be brittle from age. These really are getting hard to find in mint condition. For the money, the reproductions are every bit as good as the originals. They are also available in red and yellow.Replaces Ford part number C4VY-10B870-A.

Available in original blue light diffusers or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have, there are different numbers of diffusers (filters) needed for different years and models. Sold as a set of four. SOLD AS SET OF FOUR(4).67 - 68 Cougar Uses6 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) 2 - Oil Pressure Gauge (XR7)69 - 70 Cougar Uses5 - Instrument Cluster (XR7 or Standard) 2 - Clock (XR7) ...

Available in original blue light diffuser or custom red or yellow for a brighter "custom" look. Please note that depending on the options you have there are different numbers of defusers (filters) needed for different years and models. SOLD AS SET OF FOUR(4). 67 - 68 Cougar Uses 6 - Instrument Cluster (XR7 or Standard) 2 - Clock 2 - Oil Pressure Gauge 69 - 70 Cougar Uses 5 - Instrument Cluster (XR7 or Standard) 2 - Clock ...

Glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

Short Style glove box or glove compartment light with switch. Fits 1967-68 Mercury Cougar, 1965-68 Ford Mustang. Used switch and socket assembly, tested and working. Ford part number C5AB-14413-A1 Fits 67 CougarFits 68 CougarFits 67 MustangFits 68 Mustang

This is a correct reproduction C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used C6 arm for a 1966 - 1969 FoMoCo pony car and midsize with a floor shift C-6 transmission. This also works on the 1970 as long as the lockout rod is removed. Midsize would be Fairlane Cyclone and the individual models associated with them like Ranchero, etc. Replaces Ford Part #: C6OZ-7A256-B Check out our video on rebuilding your shifter below: ...

Used locking pawl for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. This pawl is released and via the vacuum motor when the door is opened and the ignition is in the off position. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used locking lever for the tilt / tilt away equipped Mercury Cougar or Ford Mustang. Two required per car. Here is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

This will really help you understand how your column works! Covers operation, tests and adjustments. All Mustang / Cougar tilt columns were tilt-away in 1967 - 1969. This manual is free for the asking when you purchase a tilt column from us. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* WCCC services all FoMoCo tilt and tilt-tilt away steering columns 1967-1979. Our shop rate for this service is $90 per hour and most...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

These reproduction A pillarpads / moulding / trim were used on the 1967 - 1968 Mustang Coupe and Fastback and even though they carry a C7WB part number on the back side they were never used on a 67 or 68 Cougar. Reason being is they are two wide to fit next to the wide Cougar roof side Pinch weld moulding, soft trim. If you use the thin inexpensive pinch weld moulding we sell you can use these. Also note that the 1968 1/2 standard level interior used the thin pinch weld moulding from the...

Reproduction metal trim for filling the gap between the windshield and the dash pads on all 1967-68 Mercury Cougars and Ford Mustangs. This reproduction version is a copy of the 1968 moldings. 1968 mouldings were slightly shorter in length, due to the padded A pillars pads found on Cougar XR7's. 7 attaching screws are included. Ford part numbers C7ZZ-6504522-A and C7ZZ-6504523-A.

Ninety degree bracket needed to mount the starter safety switch to the column tube in 1967.

Reproductions of the rare mounting kit brackets used to hold the shift indicator assembly to the console. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them.

We rarely have extras of these in stock but we like to show these items so you know what you are looking for or you can use it as a visual and fabricate your own kit. The washer measures 1 13/16" x 5x8" and the total length of the screw is 1 3/8" but a much shorter screw would suffice.Also available as a reproduction mounting kit. *NOTE* the raised lip of this washer faces up and only the three beveled holes on the shift indicator bezel use them. ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads.  3/8-24 threaded nut, serrated washer head style. Check out our video on rebuilding your shifter below: ...

Locking nut that attaches the shift lever to the shifter arm and support inside the shifter buckets. We normally see the fine threaded nuts on the 1967-70 shifters. Please check your shift arm support for correct threads. Check out our video on rebuilding your shifter below: ...

Unique shouldered screw that keeps your switch in perfect alignment, using incorrect screws will damage the switch.Fixed columns require 3 screws. Tilt columns require 2 screws.  *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of...

Fits 1967 Standard and XR7 Cougars or most Ford and Mercury with inside rear view mirrors. Also used on the 1967 xr7 hash marks located on the rocker.

The first in a series on production facts, this handy volume examines seven years of data from just about every imaginable statistical angle! Ever wonder how many cars were painted like yours? How about the rarest paint & trim combination...or the most common? You'll find those tidbits and many more, as we show you the figures for: * exterior color * interior trimset * color and trimset * engine * transmission * engine and trans. This book also provided the total production for RPOs -...

CRL brand glass bedding compound for installing the 1967-68 glass windshields and 1967-73 back glass that use rubber gaskets. This is a non-hardening material that seals the glass to the rubber

Four nuts per bucket seat, 8 total nuts per car with bucket seats. Sold individually. Replaces Ford part # 378643-S. Phosphate & Oil (gray & black) finish

Unlike our reproduction nuts these good used original nuts can be purchased individually and they cost less to boot! 8 required per car, 4 per bucket seat.

Quality chrome and fit. Replaces Ford Part #: C7ZZ-11650-A. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. 

Reproduction overhead console bracket for the Mercury Cougar or Ford Mustang. This is a decent part, but not as good as the original FoMoCo part we offer.

This good used original front bracket for the over head console of the Mercury Cougar and Ford Mustang. This unit is better than the repro and was also used on 1967-68 Mustang fastback. We also have the clips that attach to the overhead console and then clip into this bracket. Ford Part #: C7ZZ-65519B46-A. *NOTE* 2 are required per car.

Reproduction pair of package tray retainers for your 67 - 70 Cougar or Mustang. Made from stamped steel with a black finish to keep them from rusting. They install in the front of the package tray, keeping it secure.

NOS brake pedal for the Mercury Cougar or Ford Mustang equipped with power drum brakes. This unit will work with disc brake Cougars and Mustangs, but is not correct. That is because the power drum pad has "power brake" inscribed on the pad where the disc brake version has "disc brakes." Also, the 1967 version is narrower than 1968-73 piece.Ford part # C5ZZ-2457-E.

Quality reproduction. Replaces Ford Part #: C5ZZ-7A624-B. Dear Lin Thurston, Hi, just wanted to let you know how impressed I am, to receive a package ordered on 6-6-07 and have it arrive on 6-13-07 all the way up here in Ontario Canada. That is impressive! Your shipping department is to be commended. I must say that the mail service worked at part of it, but the speed at which your firm addresses online orders from outside your country will keep me coming back for other items! Thank you, Phil...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. This SEM Trim Black paint is a satin black acrylic coating, formulated to match the OEM finish on automotive trim parts. Good for use on plastic, aluminum, steel, stainless steel and chrome. Great for refinishing grilles, taillight bezels, vinyl top trim, pinch weld blackout, and more.No primer...

WE CAN NOT SHIP THIS PRODUCT INTERNATIONALLY WITHOUT SHIPPING IT AS HAZARDOUS MATERIAL. THIS WILL INCUR HAZARDOUS MATERIAL CHARGES VIA UPS AND SOME COUNTRIES DO NOT ACCEPT IMPORTING THIS PRODUCT. New SEM aerosol flexable paint for the Mercury Cougar or Ford Mustang. This is a great match for the 1967, 1968 and 1969 dark blue interior color. SEM brand COLOR COAT is formulated to match, restore or change color on most vinyl surfaces, flexible and rigid plastics, carpet and velour. COLOR...

New pan head screws for installing the automatic console shifter bezel. Sold as a set of 4. Used in conjunction with the 3 metal strips to attach the automatic shifter bezel. Correct black pan head Phillips screw. *HINT - The metal strips can be made from any strips of steel, they don't really need the edges folded if you don't cinch them down too tight. Metal strip should be 1-11/16" x 5/8" with a hole in the middle.

This is a general listing for anything and everything seat belt related. We can't go through and list every single seat belt part we have here, but chances are, we have what you need. If you're looking for used belts, all you have to do is call our seat belt guy (his name is Junior, at extension 209) and he'll go out in the warehouse and put together a set to match your needs and price range. We have everything from dirty old faded belts with minor rust on the chrome, to super nice, clean,...

Reproduction pillar post mouldings that feature and vinyl overlay for the Mercury Cougar or Ford Mustang. These units are sold as a pair.

1967 Cougar Owners: To view our exploded view interactive diagram of the tilt steering column parts, click here. Used pin for the locking lever in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. Two are required in 1967-69, but only one is required for 1970 and up. Recommend changing to a up dated version of this pin with one that has circlips or snap rings (15-0156 for 1967 -69 or 15-0157 for 1970-1973) *NOTE* For tilt column service, you can contact Tony...

Reproduction pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and 2 - 4 are required per car. Pin is custom made on short runs and is very difficult to find. .001 undersized, and with 8/32 threads instead of 6/32 like the originals. Newer pin removal tools will fit. Replaces Ford part # C7SZ-3D739-A. Removing pivot pins on 67 - 69 tilt away columns: Work on the upper knuckle pivot pins as there is room...

Used pivot pin for the Mercury Cougar or Ford Mustang / Thunderbird equipped with a tilt / tilt away column. This is a pressed pin with a flange and five are required per car. This pin is internally threaded with a # 6-32 thread. Ford part # C7SZ-3D739-A. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

1967-68 and 1971-73 Cougar/Mustang used bulb 1076 for Backup Lights, see part # 12175 As seen on Gearz with Stacey David. If you're looking for the best and brightest lighting for your car, look no further.  These WHITE "Plasma" LEDs are a direct replacement for 1156 and will fit anything you might have that takes an 1156 bulb (or other bulbs with the same base configuration, such as 97 and 1003 bulbs).  Basically good for every car from 1950 to 1990 that uses a 1156...

Note: Not for use with aftermarket radios. Finding correct radio knobs for a 1968 Ford Mustang or Mercury Cougar equipped with a center console has been a huge obstacle for decades now. To clear the padded radio bezel cover, one must have these elusive, one year only, deep well knobs. These will also work on 1967 Cougar with console and although they would not be letter correct for anything but a 68 with a console, they do not look out of place on a 67 with console. Note that this four piece...

This is a radio nut removal tool used to remove the radio shaft nuts. No more trying to remove those little units with the wrong tools and potentially damaging your bezel or dash. These are made from HRS steel and are milled to fit the shaft nut perfectly.

Reproduction rag joint for the fixed steering column in the Mercury Cougar or Ford Mustang. This assembly is for the fixed column only and will not work for the tilt / tilt away steering column. Our reproduction rag joint comes assembled with the lower splined casting. 

Good used part without excessive rust or damaged rubber. For use with fixed column only.

This polyurethane steering coupler repair kit for your tilt column, commonly referred to as a "rag joint", connects the steering shaft to the input shaft on the steering box. Some customers feel polyurethane improves steering feel. Replaces factory steering coupler on 1967 - 1973 cars. Most 1967 Mustangs with fixed steering columns do not have coupler.Replaces Ford Part #: C7OZ-3A525 Check out this video ...