Interior

Used electrical wiring harness that plugs into the main under dash loom. Two wire harness with light socket and shroud for all 1969-70 Mercury Cougar. This can be made to work on a Mustang. Ford number C9WB-14412-A printed on the wire harness.Fits 69 CougarFits 70 Cougar

This is the same sound deadener kit that everyone else is offering, but if what you are looking for is a kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least...

If what you are looking for is a sound deadener kit that fits and performs as good or better than the original... What you get when you order this kit is rather disappointing. For years we have not sold any underlay kits at all, we have just suggested you get your dose of disappointment closer to home and save the shipping costs or visit your local stereo store and see what high tech "cut to suit" materials they offer. Well, at least this listing will give you an honest idea of what you are...

5/16" thick sound deadening and heat reflecting material, comes in a 4' X 6' sheet that can be cut to fit. This insulation consists of two layers of polyethylene bubble film sandwiched between two layers of aluminum foil. Temperature range rated -60 deg. F. to 180 deg. F. Combining this with the tar-based sound deadener underlayment will result in similar sound deadening as the OEM sound deadener.Below is listed how many rolls you will need to underlay the sections of a Cougar:  Area...

This sound deadener is comprised of one layer of tar sound deadener and a layer of Jute. Here is a shot of the original sound deadener pulled (slightly) apart to expose the en-capsuled insulation.  This new OEM style sound deadener is very similar, but is lacking the extra layer of tar on the bottom.  This can be overcome by adding the tar only kit to this kit.  This combination will come by far the closest to OEM than any other kit available! ...

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Used steering column tube and locking pawl spacer for the Mercury Cougar or Ford Mustang equipped with the tilt / tilt away steering column. This unit is used to align the inner steering column tube and align the locking pawl cable with the lower flange. Ford part # C9SZ-3C708-A.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

Good used and working speedometer from 1969-70 standard model Cougars. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work correctly. 1969 and 1970 standard speedometers all look exactly the same on the front, but the 1969 is white backed, and most of the 1970 ones are bare steel color. Replaces...

Good used and working speedometer from 1969-70 XR7's and Eliminators. Grade A used, tested and will have good numbers on the odometer section. (Our Grade B examples are fully functioning, but will have worn numbers on the odometer section. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the comments section of your order. Good used unit that is not overly faded and guaranteed to work...

Good used and working speedometer from 1969-70 XR7's and Eliminators. Grade B used, tested and will have faded or missing numbers on the odometer section, generally the dials look black where the white numbers have worn or faded off. (Our Grade A examples are fully functioning, and will have legible numbers on the odometer section. We cannot guarantee your desired odometer reading but since we always have multiple units in stock we can at least try. Please request mileage reading in the...

This is the plastic center piece you press down to release your seat belt on the 68 - 72 seat belts. It comes unbroken and without cracks. This button piece has original decal with starburst design. Spring is included. Check out our video "All about seat belts" below.

Better quality than our reproduction for less money. Ford part number C0DZ-13807-A.

This gives the thumb release button in your T shaped shift handle its tension. If it is rusted then your button will not return back to its outer position easily. Fits 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Technically this spring fits all Ford and Mercury floor shifters 1965-73. Ford part number C5ZZ-7C300-A. The MPC shows this spring to have a free length of 2-1/16 inches.

Used spring cap that is used in the tilt / tilt away steering column found in the Mercury Cougar or Ford Mustang. One required per car. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

This clip is the same as a door panel clip with the exception that it does not have the foam spacer. This clip was used on the 1968 XR7 overhead console, 1967 - 1968 xr7 and standard model upper and lower console pads, seat back access panels and several other applications. This original clip holds tighter than the reproduction. We recommend using this used clip over our reproduction for applications like the seat back because the reproductions often do not cut it. Ford part number...

Don't try to straighten your rod if it looks like this. The contour seen here is correct. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

NOS lens for the Standard model Cougar optional clock. Not the same as XR7, this clock is would be located in the gauge panel on the driver side instrument cluster. Nice quality, NOS, not polished lenses. Fits 1969-70 Mercury Cougar Standard, body style 65A, 65C, and 76A. Made by Borg Co., which originally made these lenses for Cougars.  *Note - excludes XR7 and Eliminator.

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber. 16 individual pads in a package.

Used tilt / tilt away steering column converted into a tilt only unit for the Mercury Cougar or Ford Mustang. All 1967-69 Cougars and Mustangs optioned with a tilt column also had the tilt-away (aka tilt-swing, tilt-fly or tilt-pop). There was never a tilt only option in 1967-69 Cougar or Mustang, no matter what you may have been told... That being said some of our customers prefer not to have the added expense or complexity involved with the swing-away function. This column has been fused at...

Fixed steering column from a 1969 Mercury Cougar or Ford Mustang. Reasonably rust free column, collapsible style. Ships as shown in picture. Often we will leave the turn signal switch in place but you should count on it being non functional. Two piece collapsible shafts have tiny plastic pins these often brake due to age or handling. Lower shaft may need to be pushed up or down for proper fitment, this is a common occurrence. Upper and lower mounting brackets, are available, but sold...

This is my most favorite Cougar - Mustang - Shelby option of all time! In fact as a rather tall person, that is not as slim as I once was, I do not really enjoy driving a Pony car that does not have this option anymore. This column does not only manually adjust up and down with the depression of the turn signal wand, it also releases and swings up and towards the passenger side of the car each time the ignition is turned off and the door is opened. To start the car you must close the door and...

This is a one year only, Cougar only part. I do not care what they told you down at the "Mustang Mega Barn", Cougar is different as it has mounting holes at the top and Mustang does not. The Mustang cover has no mounting holes at the top and resembles the 1970 cover. This may just be the most delicate part found on a 69 Cougar and is just behind good used interior sail panels in scarcity. Rarely do we have this in stock and we can almost assure you we will never be able to come up with the...

Quality reproduction lower column cover for the 69 Cougar.  Grommet sold separate. NOTE* This is not a Mustang part, the Mustang version is similar but has no upper mounting holes.

Reproduction rim blow steering wheel for any 1969 Mercury Cougar or Ford Mustang, and generally any other Ford Lincoln or Mercury with tri-spoke rim blow steering without speed control. Brand new to market, black is the only color. These now come with the switch pre-installed! We asked long time Cougar collector and restorer Randy Carlson to give us his honest opinion of this new to the market wheel and this is how he responded; "Be ready to cut the box to pieces to get the wheel out of the...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Note that the color on these has too much gray in it and is...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Having issues with wobbly or loose steering? Check out our...

Pictured in black. This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad. Having issues with wobbly or loose...

This steering wheel was used only on standard interior 68-69 Cougars and will not fit a 1967 or 1970 - 73. Most Cougars were equipped with decore or XR7 interiors which used a two spoke wheel with woodgrained rim in 1968 and an all together different three spoke Rim Blow wheel in 1969. If you have a deluxe woodgrained wheel in your 1968 decore or xr7 equipped Cougar this solid colored wheel will accept your existing horn ring and pad.

Core wheel good only for restoration. We have a very hard time keeping these in stock due to their popularity in Australia. If you have any 1969 3 spoke rim-blow steering wheels for sale we would like to hear from you! 503-463-1130 Having issues with wobbly or loose steering? Check out our video on sloppy steering below. ...

Description: This one year only, three spoke wheel was used on all Cougars in 1969 except the Cougars equipped with standard interior. The standard interior Cougars used the solid colored two spoke wheel. The un-restored XR7 pad and bezel shown are not included with the wheel, they are sold separately. As we prefer to start with a very nice core wheel, a good core wheel is required in exchange or a core charge will apply. We choose to only send in wheels that are not separating or have large...

Good used wheel with no cracks. Will need horn switch replaced. We will take your core(s) in trade for this wheel, send us enough 1969 core wheels and we can do a straight across trade.

Please email us for color on hand, rarely do we have more than one grade A in stock. Grade A will have almost no warping or lifting issues, soft and pliable and will not need repaint. Very hard to find, one year only part.

Good used pad available in most colors, please let us know which color you need in the comments section and we will try to accommodate. Grade B pads will be lifting at the top, be a little warped and have some missing texture where your thumbs often ride at 3 and 9 o'clock.

Not the best fit, texture is incorrect. Guaranteed disappointed, no returns on this item please.

Excellent quality reproduction sun visor assemblies and corner trim for the convertible 1969 - 1970 Mercury Cougar or Ford Mustang. These feature the correct satin finish, fit perfect and look spot on. Sold as a pair, the original passenger side part has a C9ZB-7604122-C casting number on the back side and the driver side reads C9ZB-7604123-C. These will also interchange with versions ending in A B or D. Later versions will show one less screw tab. Replaces Ford part # C9ZZ-7604144 /...

Used single hole front mount center visor bracket for the 1969 / 1970 Mercury Cougar and Ford Mustang hard tops.  The colors don't always match the seat color, so plan on spraying these with vinyl paint to match your interior. We often times can supply your desired color, mention your desired color in the 'comments' section of your order. Ford part # C9AZ-6204132, casting # C9AB-6204132-B.

Used 2 hole front mount center bracket for the sun visors in the 69 - 70 Mercury Cougar or 68 - 70 Ford Mustang convertible. The Master Parts Catalog (MPC) shows a specific part for the convertibles, but we have found three different styles of the sun visor arm clips used in the 68 - 70 convertibles.  Casting# C8OB-6304132-A has no dividerCasting# C8ZB-6504132-A has a partial divider (Most Common)Casting# C8ZB-6504132-B has a complete divider.  The colors don't always...

This is the 1968 coupe version of the 2 hole front mounting sun visor center bracket and is a close match for the 1968 / 1969 / 1970 convertible sun visor bracket.  This bracket is not, however, an exact match for 1971 /1972 / 1973 convertible as some sites suggest, but it will work. On the 71 - 73, the hole spacing and distance from the windshield are identical to this bracket, but the bracket is not the same size. This bracket is 1/8" longer on the...

Reproduction single hole front mount center visor bracket for the 1969 and 1970 Mercury Cougar or Ford Mustang. This is a decent reproduction, but not quite as nice as the originals. Reproductions only come in 'paint to suit' black but we have most original colors in used. Replaces Ford Part #: C9AZ-6204132.

For the purists out there we have a very limited amount of used visors that have no impressions, seam separation and minimal rust on the clips if any. Convertible and Coupe are the same.Please indicate the color desired and we will try to accommodate but painting might be required.Sold individually

Reproduction sun visors that are fully padded and covered with the correct textured vinyl to match the seats. These units are sold as a pair.