Engine & Under Hood

Reproduction pair of brass oil cooler fittings for the Mercury Cougar or Ford Mustang that screws into the oil cooler. 1/2" threads go to cooling lines.3/8" threads go into the radiator.

Steel freeze plug or expansion plug set for any Ford 390 / 427 / 428CJ engine. 1967-70 Mercury Cougar and 1967-70 Ford Mustang. 17 piece set with threaded screw in plugs as shown. 

Round ring shaped gasket that goes on top of the carburetor. Protects and seals the carburetor to the air cleaner.New Old Stock Ford gasket, Ford part number C5ZZ-9654-B.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-73 small block Ford engines with size 351 cubic inches, Windsor engine only. 1969-70 Mercury Cougar and Ford Mustang with 351W engines.Any doubts? 351 windsor engines have 6 bolts holding the valve covers in place. 351 Cleveland engines have 8 bolts holding down the valve covers.*Note - Excludes 289/302 engines. *Note - Excludes 351C or 351 Cleveland engines.

New gaskets for installing your intake manifold. This is the Felpro branded gasket. Fits 1969-70  Boss 302 Ford engines. 1969-70 Mercury Cougar Eliminator and Ford Mustang with G code 302HO engines. *Note - Excludes 289 / 302 / 351C / 351W engines. 

Ford casting number C8AE-6316-C Includes all 1969-70 Q or R code 428SCJ engines or those cars with the drag pak option. The C8AE-6316-C harmonic balancer is identified by the 3 bolt holes for attaching the crankshaft pulley. Outside diameter is approximately 7-1/2 inches. Ford part number C8AZ-6316-C. Has the timing marks on rim. The rubber in this used balancer will be the original and will not be showing cracks or signs of having shifted. This good quality used balancer is a good option for...

Used original heat riser / S tube for 1968, 1969, and 1970 Cougar and Mustang 428 Cobra Jet / Super Cobra Jet. These will seldom be available. The one pictured above is the best example we've ever seen - removed from the car in 1969 just days after purchase. The pictures below are a more realistic example of the used condition you might expect. There are also additional comparison shots next to the reproduction S tube we also sell. The differences are small but the most obvious is the fact...

Used grade "A" heat shield for the Mercury Cougar or Ford Mustang equipped with either the H code 2V or M code 4V 351 Windsor engine. This metal shroud and tube assembly attaches to the factory air cleaner assembly and really finishes off the engine bay. Ford part # C9OZ-9A603-A.*NOTE* For 1970, this shield was used after the build date of 2/2/1970, but it can also be used on prior dates. We suspect that the early 2 piece shroud was discontinued because of rattling noises or some...

This two piece heat shield has a very narrow application in that it is a one year only item and only for the 390 IP (Improved Performance). It does not mate to metal a "S" shaped heat riser tube but rather a flexible paper-foil tube that attaches to a reducer on the bottom side of the snorkel. Very hard to find item, harder yet to find one that has not rusted out. The unit shown is "tender" in a couple of spots. The lower section carries a Ford part number of C9OZ-9A603-D and the upper section...

C8OZ-9A603-B metal shroud that attaches to the passenger side stock cast iron exhaust manifold. Works in conjunction with a metal 'S' tube sold separately (C8AZ-9652-A). R code and Q code Cobra Jet engines only.

Reproduction Boss 302 Exhaust Manifold Heat Shield for the 1969 Mercury Cougar or Ford Mustang

Ford part number C9ZZ-9A603-C for the upper section and C9ZZ-9A603-D for the lower for this two piece metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this lower section also. metal shroud unique to G code Boss 302 Cougar Eliminators. *Note - Very early 1970 Boss 302 cars build prior to 9-2-1969 used this upper section also.

This item has been discontinued until further notice.Basically correct looking except for screws in place of the rivets. The High or Low tone is indicated in raised letters located on the perimeter of the horn. Replaces Ford Part #: C9ZZ-13832 / C9ZZ-13833 or C9ZF-13801-B / C9ZF-13802-C.

This item has been discontinued until further notice.The High tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13832 or C9ZF-13801-B.

This item has been discontinued until further notice.The Low tone is indicated in raised letters located on the perimeter of the horn. We do offer the correct used Cougar horns.Replaces Ford Part # C9ZZ-13833 or C9ZF-13802-C.

Tested and working used Lo tone horn. The Lo tone is indicated in raised letters located on the perimeter of the horn. 1969-70 Mercury Cougar and Ford Mustangs used part number C9ZF-13802-C Lo tone. Every horn is bench tested and inspected for cosmetic defects, if they do not function properly, and pass a visual inspection, they get recycled. The used horns at WCCC can be used as-is or you can clean and detail them for you show car.

C9OZ-6A664-A Original used hose that connects the original PCV valve to the carburetor spacer plate. All 1969-70 351 Windsor 2V and 1969 351Windsor 4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. This hose is a bit longer than the 289/302 version due to the taller deck height of the 351 Windsor engines. *Note - These molded and contoured hoses were designed to work with the...

C7TZ-6A664-A Used after 02-21-1969. Original used hose that connects the original PCV valve to the carburetor spacer plate. All later 1969 S code 390-4V engines. Used hoses will have faded striping (if present), and clamp impressions. Very often the rubber will be hard and showing some degree of stress cracks. *NOTE* These molded and contoured hoses were designed to work with original style PCV valve (modern 90° PCV valves won't work). Additionally anything other than period original intake...

Looks right and it works, but belt alignment will be off. Needs about 1/8 inch of shim to align with the other pulleys. See pictures. This adjustable bracket and pulley can be used on all 1968 - 1973 Cougars or Mustangs with the V-8 engine as long as they have the "stamped steel" lateral air compressor support brackets. This bracket will only have the big bearing pulley and may have various casting numbers such as D5TA-8A617, D3OA-8A617, D5OA-8A617, D8OA-8A617, etc. This is a...

New old stock bracket and pulley assembly for Cougars or Mustangs equipped with the 289, 302, or 1969 351W engine. We also offer a bearing replacement service to rebuild your 289, 302, or 1969 351W fixed idler pulley, see item 27539. Ford part # C8AZ-8678-C. ...

Used fixed idler bracket and pulley assembly with new installed bearing for 1968-69 Cougars and Mustangs with the 390 or 428CJ engine. This part will have a small bearing on the pulley and is not marked with a casting number. The 1970 bracket and pulley assembly was a service replacement part and are the same as the 68-69 with the exception of a slightly larger bearing. This later service replacement part is an economically priced service replacement for the earlier originals. All pulleys come...

C8OZ-3C511-B Rear power steering pump support bracket. Also called the high pressure hose indexing bracket. For any 1968 - 1970 Cougar or Mustang with any of the 390 / 427 / 428CJ engines. OEM used part designed to maintain the position of the high pressure power steering hose from coming in contact with with moving or high heat parts. *Note - May or may not work with non-original or replacement high pressure hoses.

C9ZE-9425-A or -B Cast iron intake manifold used on all S code 390-4V engines in a Mercury Cougar or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-A or -B. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-A. Current date 8H14.*Installation Tip - A water heated aluminum spacer plate with PCV provision is needed for proper air cleaner clearance....

C9ZE-9425-D or C9ZE-9425-E Cast aluminum intake manifold used on all 1969 G code Boss 302 engines in a Mercury Cougar Eliminator or Ford Mustang. Stock 4 barrel intake manifold. Take off manifold with correct casting number of C9ZE-9425-D or -E . Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford master part number C9ZZ-9424-C. Has "Buddy Bar" cast into the bottom side.

Cast aluminum Sidewinder intake manifold. Over the counter speed part for the 427 Medium Riser. The offset carburetor placement was to help provided equal length runners in regards to flow. Single 4 barrel intake manifold as shown. Looking closely at the photos, this one has had a repair performed in the past. Intake shipped bare, less carburetor studs, heater tube, vacuum fittings, and water neck where applicable. Ford casting number C6AE-9424-J.

This lid is about 16-3/4 inch in diameter. Identified by the spokes in the stamping. 1967 and 1969 Mercury Cougar and Ford Mustang with S code 390-4V engines. Additionally this lid was used on 1969-70 Q code 428CJ or non-ram air Cougars and Mustangs. We believe that this lid was also found on Boss 302 Eliminators. This was originally a chromed lid, plating will usually be poor or missing on these used units. Plan on sending to the chrome plating company prior to use. Ford part number...

Rechromed GT air cleaner lid for the Mercury Cougar and Ford Mustang equipped with either the Boss 302, GT 390, or 428 CJ engine without the shaker option. It was possible to order a 390 GT motor for your Cougar without ordering the 390 GT package. Cougars equipped with the S code 390 6.5 Litre engine, that did not come with the GT package, would have used the painted air cleaner lid. Replaces Ford part # C7OZ-9661-A.*NOTE* The outside dimension of the lid is 16.75 inches and will not fit the...

This is a 1969 lid. The 1968 lid had several differences, most notable was the stamping wrinkles. This is  Flapper mid plate for use on non-shaker cars. 1969-70 Mercury Cougar with R or Q code engine with ram air. 1969 Mercury mid sized cars such as Montego, and Cyclone all with R code 428CJ or SCJ engines. Ford part number C9ZA-9600-C. This version is said to have been used starting in May of 1968, so there would have been some cars equipped with this mid plate.There are many...

Used engine or 'motor' mount for any 1969 Mercury Cougar or 1967-69 Ford Mustang convertible. There is not a replacement engine mount for the 1967 cars with 289 engine. These have the Ford casting number of C7ZA-6038-F, in the rubber. The mounts that we have in stock are a 30 year accumulation, needless to say it is very limited supply. They all appear to be in good shape without cracks in the rubber. We offer them for those enthusiasts that want correctness for concours judging, we suggest...

Bracket used to mount the thermactor air pump. Casting number C9ZE-9B450-A or C9ZE-9B450-B. Ford part number C9ZZ-9B450-B

Application is for the FE engines 390, 427 428. This assembly is needed for the installation of the cylinder head air supply tubes. Sold as one nut / one ferrule. 8 total needed for smog tube attaching. Originally these were installed in conjunction with a lower tube.

Used 1970-72 black AUTOLITE marked oil fill cap with black plastic elbow. Several variations noted from our collection, AUTOLITE and MOTORCRAFT versions. Will need detailing or fresh black paint applied. Would also suggest replacing the rubber grommet. These 50 year old rubber grommets are rock hard and likely leak air. Gasket to valve cover will also need replacement. Even though this cap has a 1971 parts number, we see these on the 1970 351C engines quite often. Replaces Ford part...

Precision machined to the factory specifications. Light gold anodize finish just like the original.

Factory oil cooler as used on 1969-70 R and Q code Super Cobra Jet 428 engines. Nice used condition, comes as shown with one fitting. Will also work for installing an external oil cooler on the other FE motor applications.Ford part number C9OE-6884-B. 

Nicely chromed dipstick tube and dipstick for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor. Replaces Ford part # C9OZ-6750-A or D0AZ-6750-C.

Chromed engine oil dipstick as found on all 1969 Mercury Cougar Eliminator and Ford Mustang with Boss 302 engines (G Code). The handles were chromed originally. Ford part # C9ZZ-6750-A, Ford casting # C9ZE-6750-A.

Concours correct dipsticks for 1967 - 1969 big block engines. These are exact reproductions of the originals with the proper length and oil level for these big block FE's. They have all of the correct markings including the Ford part number and recommended oil weight. Each dipstick is finished with a show quality chrome handle capped with the correct plastic plug. Ford part # C7OZ-6750-A, Ford casting # C7OE-6750-A.

Reproduction blue dipstick tube for the Mercury Cougar or Ford Mustang equipped with the 351 Windsor.

This oil filter is absolutely concours correct. A must for Show. All are silk-screened with multiple colors.

The oil filter made by the original Ford supplier.

New Old Stock oil filter adapter from any 1968-70 Ford with 390 or 428CJ (non SCJ). Fits Cougar, Mustang, Torino, Fairlane, Cyclone, Ranchero, etc. Nice cast aluminum bracket for installing the spin on oil filter and oil pressure sending unit. Ford casting number C8AE-6881-A. Will fit 1967 FE engine blocks too. Those technically used an adapter with a casting number of C0AE-6881-A.

Famous 'Cal Custom' aluminum finned oil pan that was so popular throughout the 60's, 70's and 80's. It has not been available for years, but it is back again. Pan is made from all new pressure die cast tooling and then fully machined to offer a precise fit and leak free installation. These look great in combination with the Finned Air Cleaner and Valve Covers. Replaces Ford Part #: C5ZZ-6675.

Includes drain plug.

New pair of white and yellow paint sticks for the Mercury or Ford. These units were used by FORD at the assembly plants to mark fender aprons, radiator support, transmission, rear end housing, sheet metal, glass and variety of other parts. It's often little details like this that separate first and second place at the show.

Front steel vacuum fitting for 390, 427, 428CJ engines. New Old Stock. Replaces Ford part number C7AZ-9A474-A.

New old stock brass intake manifold fitting that screws into the rear of the 428 CJ intake manifold on all 1969 428 Cobra Jet engines. Similar to the 1967-68 version, but this one has an additional smaller nipple coming out of it.  Ford part number C8OZ-9A474-A.

Used threaded PCV valve for use on 390-4V, 428CJ, 427-4V cars from 1967-70. Unknown functioning condition, these have the correct threaded tops and work with either of the 90° elbows available, reproduction or OEM Ford.

Pertronix brand 7mm spark plug wires. These are performance oriented wires compared to the concours spark plug wires. For any 1967-73 Mercury Cougar and Ford with 289 or 302 engines. Black wires and boots, quality spark plug wires taylor made for the small block Ford engines. Recommended by Pertronix for use with the Flame Thrower coils.