Bumpers & Trim

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 3 piece set, which includes: D1WY-8282-A and D1WY-13B116-A. Passenger side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

This body part is painted body color and mounts vertically on either side of the center grille. Grade "A" part with no rust or dents, ready to paint and install. This is a 2 piece set, which includes: D3WY-8282-A and D3WY-13B116-A. Passenger side filler between grille and headlight assembly. Does not include chrome trim or hood rubber bumper on top.

This tubular support gives rigidity to your hood extension which houses your center grille. These are hard to find with no bends or cracks due to the fact that the 1970 hood protrudes in the center.1 required per car.

Used upper support bracket for the hood latch on any 1969 Mercury Cougar. Ford part number C9WY-16707-A.

Used upper support bracket for the hood latch on any 1970 Mercury Cougar. This 1970 part will work on a 1969. The only difference is the top corner is clipped at an angle on the 1970.Ford part number D0WY-16707-A.

Unlike the 1968 Cougar headlight switch, the 1967 and 1971-73 version does not have the three vacuum ports connected to it. Don't be fooled . . . Most vendors will sell you a Mustang switch and tell you it is the same. Visually it may look the same but internally it has a circuit breaker designed for a two headlight system, the Cougar has four headlights. If you only use the low beams you would be fine but if you have all four lights on you will soon experience a blackout. If your original...

Used headlight switch for the Mercury Cougar. This original FoMoCo unit was tested and will hold 13 pounds of vacuum. The spacer (which is specific to 1969) is not included with this unit, but you can get it right here. Ford part # C9WB-11652-B.

This is a tested original FoMoCo headlight switch that will work, there is no warranty. The primary reason we list these old used switches is that some people are missing their switch altogether and need the beveled cup shaped spacer that mates to the dash. As pointed out in our listing for the reproduction headlight switch, the spacer is not included with our new units. Ford part # D0WB-11652.

Quality "STANDARD" brand reproduction switch for your vacuum actuated hideaway headlights. This switch fits multiple years and makes which means multiple dash configurations. You will need to "break off" your unique extension and attach it to this unit. The extension (spacer) can be removed easily by placing your old switch in a vise and using a wedge shaped chisel to break the tiny spot welds. When reattaching, most any glue such as Gorilla glue, JB weld or even silicone will work as you are...

Good used grade "A" taillight bezel for the 67-68 Mercury Cougar. This grade "A" unit will not have any pits, bends on the ribs and the chrome will have good luster. When you mention it in the comments section, we will try to pick out examples that still have the detail paint in tact. This no excuses bezel will look great on your high quality unrestored driver. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most...

Good used driver quality grade "B" bezel with no bends, cracks or deep pits. Chrome will have a decent luster (not perfect), but the paint will need to be redone. If you want show quality then the only way you will be happy is to buy our rechromed bezels. Right and left are interchangeable. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our...

These never came on a Cougar; these are reproduction 1967 Shelby tail light lens bezels. The reason we list them is that over the years many of our customers have been cutting out their vertical ribs on the 1967-68 Cougar tail light bezels to completely expose the tail lens.  These Shelby bezels offer a direct replacement clean restomod look without all the hassle of cutting up your valuable Cougar parts. As the close up will show there are slight machining marks so you may want to polish...

Sold as a pair. New to the market as of 2009. Take a look at our many pictures below of these bezels installed with original backing plates and lenses. *NOTE* Need help diagnosing a Cougar turn signal problem? Victor Yarberry is the world’s most knowledgeable expert on the subject. Vic has owned Cougars since the 1970's and is the designer of all of our solid state sequential systems. There is no question he cannot answer! Here is a link to a great source of information on the subject. Check...

Sold individually, two required per car. This is the same as the 1970 bracket, just different design of clips are used.

This bracket attaches the vacuum storage tank for your headlights to the core support inside the driver fender. It differs from the 1967 bracket in that an oval hole was put in it to allow the socket and pigtail assembly for the side marker light to pass through the bracket located closest to the fender. 1969 uses the exact same bracket except for a slightly different clip design. Sold individually, two required per car. Cougar part number C8WY-13B008-A.

This bracket is used to mount the vacuum storage tank under the driver side fender. Same bracket as was used in 1967 just a slightly different clip. Two required per car, sold individually. Cougar part number D0WY-13B008-A. *Note - The 1967 bracket was used prior to 11/10/1969 built date.

1970 Mercury Cougar hideaway headlight vacuum tank installation brackets (pair) with fasteners. Two different styles of installation brackets for the 1970 vacuum tank found inside the driver side fender. These are tall brackets, the other style utilized 1967 brackets with round spacers.

All parts needed are included to mount your 1970 vacuum storage tank to the core support (backside) under the driver fender. Solid, good original parts found on a Western donor Cougar. Includes short brackets with correct clips, 4 spacers, 4 long bolts with washers, and 4 shorter hex bolts. Typically this kit was used for installing the vacuum tanks until Nov 1969, it is much more convenient to use the more common later kit for the 1970 tank installation.

These tension springs are located on either side of your hidden headlamp eyelids. Our springs are made from the exotic alloy "Inconel". Inconel springs have approximately ten times the memory of the originals which were made from the much more common and inexpensive "piano wire". These springs have been engineered to have the exact same elasticity as the originals but will last decades longer than the originals which from our experience with NOS, usually lose their memory within a year and...

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact.

Good used part with light pitting. This part would be suitable for a driver or a good candidate to have restored. Both studs will be intact. NOTE - When sending in your core, light pitting on the upper edge is acceptable. Heavily pitted trim will not be accepted.

This two piece painted trim / moulding set helps to secure the package tray in place at the bottom of the rear window. Our used pieces taken from parts cars usually need to be painted but sometimes will pass as is for a driver quality car. We cannot promise we will have your color in stock but we will try to accommodate your request of color.

1967-68 XR7 over head console pad clip. Two needed per car. Sold individually # C3AB-63519A16

Replaces Ford part #: C7ZZ-3656-A, concours correct for all 1967 Mustang's and Cougar's. This beveled ornamental plastic ring is for your 1967 steering wheel hub. The inner diameter is 3 3/4" and the outer diameter is 4 3/8" and it stands 5/16" tall. This ring fits many FoMoCo products but keep in mind there is another version that is completely flat like a washer. We suggest you use soapy water and heat your hub before trying to slip this on. It also helps if you go around the perimeter and...

Seven (7) of these acorn nuts are used to hold the trunk trim moulding on to the trunk. Replaces Ford Part # 377767 For more insight on this tricky trunk trim, check out our video below: ...

Used headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the common version with the separate ground wire where very early 1967 Cougars and Thunderbirds did not have that separate ground wire. We won't always have these used units in working condition in inventory. We also sell a rebuilt solenoid here. Ford part # C7SZ-13A161-A. *NOTE* This item will not ship until a rebuildable...

Used headlight solenoid valve for the vacuum headlight system on the Mercury Cougar and Ford Thunderbird. This functional unit is tested and ready to install.  This is the common version with the separate ground wire where very early 1967 Cougars and Thunderbirds did not have that separate ground wire. We won't always have these used units in working condition in inventory. We also sell a rebuilt solenoid here. Ford part # C7SZ-13A161-A. *NOTE* This item will not ship until a rebuildable...

Good rust free tank taken from a Western parts car. Differs from other years in that the vacuum port is located in a different position. Located under the driver fender. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number C9WY-13A185-A.

Good rust free tank taken from a Western parts car. Differs from other years in that the vacuum port is located in a different position. Located under the driver fender. Keep in mind we have units that are not as clean but still hold vacuum for about half the price. Cougar part number C9WY-13A185-A.

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the larger curved rear driver side, about 47 inches in overall length. Ford part number D1WY-655517A37. No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the horizontal driver side, about 38 inches in overall length. Ford part number D1WY-65423A19-C. No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the larger curved rear passenger side, about 47 inches in overall length. Ford part number D1WY-655517A36. No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the horizontal passenger side, about 38 inches in overall length. Ford part number D1WY-65423A18-C. No core charge required. 

New Old Stock vinyl top moulding from any 1971-73 Mercury Cougar. This is the small driver side rear, about 6-7 inches in overall length. Ford casting number D1WB-65550416-AA part number D1WY-65423A19-C.   

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the small driver side rear, about 6-7 inches in overall length. Ford casting number D1WB-65550416-AA part number D1WY-65423A19-C.  No core charge required. 

Used vinyl top moulding from any 1971-73 Mercury Cougar. This is the small passenger side rear, about 6-7 inches in overall length. Ford casting number D1WB-65550416-AE. Ford part number D1WY-65423A18-C. No core charge required. 

This is the correct size walking cat decal for your eyelid door on the 1967 - 1969 Cougar. It has the studs in the exact place as the originals. You will need this emblem when changing out our 1967 - 1969 background decals as you will have to break the original studs to remove the cat. Also great for those custom applications! Emblem is approx 3 3/4" wide by 1 1/4" tall. This cat does come with two flat attaching clips. *Customer Feedback* Hey Don and Lin, Just wanted to send a couple pictures...

Bumper bolt wavy washer sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as...

Driver side stainless steel weather strip retainer for 71-73 Cougar and Mustang convertibles. This retainer screws to the windshield pillar post and holds the weather stripping for the front of your door window glass. Plan on replacing the weatherstripping. There is also the companion lower aluminum retainer listed on our site.These used stainless pieces generally polish up very well with 0000 steel wool. The little black plastic coated clip will be compromised due  to age and...

Passenger side stainless steel weather strip retainer for 71-73 Cougar and Mustang convertibles. This retainer screws to the windshield pillar post and holds the weather stripping for the front of your door window glass. Plan on replacing the weatherstripping. There is also the companion lower aluminum retainer listed on our site. These used stainless pieces generally polish up very well with 0000 steel wool. The little black plastic coated clip will be compromised due to age and heat.Replaces...

Reproduction driver side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1967-68 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5387. Shipping will have...

Used driver side (left hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will have...

Used driver side (left hand) aluminum channel for installing the roof side, or upper door and quarter window weatherstripping. Right and left sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5392. Shipping...

Reproduction passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation. Plan on installing a new roof rail weatherstrip. Shipping will have to be by dimensions, as this is an oversized item. Hardtop or sedan models only, not for convertibles. NOTE: These decent...

Used passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Passenger and driver sides are contoured differently and are only for the 1967-68 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5387. Shipping will...

Used passenger side (right hand) stainless steel channel for installing the roof side, or upper door and quarter window weatherstripping. Driver and passenger sides are contoured differently and are only for the 1969-70 Mercury Cougar. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item 5645. Shipping will...

Used passenger side (right hand) aluminum channel for installing the roof side, or upper door and quarter window weatherstripping. Passenger and driver sides are contoured differently and are for the 1971-73 Mercury Cougar and Ford Mustang coupes only. These channels also have pre-drilled holes for installation and often times the assembly line workers 'made their own holes' so there often times will have additional assembly line holes. Plan on installing a new roof rail weatherstrip item...