Bumpers & Trim

Used passenger side (right hand) grill section for the Mercury Cougar. 1967 is unique from the 1968 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. 1968 had a more durable reinforced casting in this area. This grille half has been carefully inspected and found to be free of pits or major scratches in the chrome and is not severely warped. It will have a misalignment issue as they all do in the portion on the outer most corner...

Used grade "B" passenger side (right hand) grill section for the Mercury Cougar. 1968 is unique from the 1967 grille in a couple of ways, but the most noticeable is the upper mounting tab where it bolts to the grille center. This 1968 piece has a more durable reinforced casting in this area. This grille half has been carefully inspected and may have some minor cracking, but will have good chrome with no pits, major scratches, and is not severely warped. It will have a misalignment issue as...

Used grade "C" Passenger side (right hand) grille section for use as a patch for those with a break in the section that continues to the fender. Watch the video below to see how to fix your current grille and save a lot of money. Check out our video on grille repair

Used grade "C" Passenger side (right hand) grille section for use as a patch for those with a break in the section that continues to the fender.  Watch the video below to see how to fix your current grille and save a lot of money. Check out this video

This one year only part fits inside the 1969 lower column cover and fills the gap between the column tube and plastic cover of non-tilting steering columns. It is color coded to match your column and lower dash. Please select your desired color in the comments section, and we will attempt to accommodate you as close as we can. Usually we will have your desired color in stock. Original Ford part number C9WY-3K680-A. *NOTE* - The 1969 Ford Mustang has a different part number which is...

This listing is for all six pieces restored and of course requires you send your cores in advance. It can take anywhere from 1 to 4 months depending on what time of year it is and where we are in our cycle with our plater as we send a minimum of $20k in at a time. We make sure they are separated from the more common parts we have and these are treated with special care every step of the way. On this particular set we never ask them to hurry. Do know that if you have extra holes drilled they...

This complete set of grille bars have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.If you send cores in for exchange they must be pit free and no scrapes so as to qualify for...

This pair of tail light bezels have been chemically dipped to remove the chrome and are ready to be painted black for your 1967 - 1968 Resto-Mod or 1968 GTE. Keep in mind when an item is chromed, the layer or layers of copper plating act as a primer to fill in minor imperfections. You will have some prep time involved before these are paint ready. We hand select premium parts that have minimal defects.  If you send cores in for exchange they must be pit free and no scrapes so as to...

This used bracket kit is what is needed to mount the headlight vacuum storage tank inside the front of the driver side front fender. This kit differs from the 1970 kit only in the slightly different design of fasteners used.

Includes all the hardware needed to mount your 1968 vacuum storage can located inside the driver fender. Parts do not come cleaned as shown, we clean many of these used parts so as to show the details and true condition of the part you can expect to receive.

Complete mounting kit for the vacuum storage tank located inside the front portion of your driver side fender.

Reproduction headlamp adjusting nut and screw. Slightly longer screw than stock, small amount of added length does not interfere with anything in or behind the grille. The nut is an exact copy of what is found on the 1969-70 adjustment. Almost the same as the nut found on the 1967-68 Cougar, this isn't even shown on those grilles. 1967-68 mounts on the backside of the headlight bucket. Total of 8 adjustment screws used on each 1967-70 Cougar, item sold individually.Note: When installing...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16A and "H", There are four different versions used, but they are the same for the 1969-70 Mercury Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68, but was moved...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7OB-37B and "RL", There are four different versions used, but they are the same for the 1967 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-37-A. Right hand low beam holder. Ford part...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "L", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used on 1967-68 Mercury...

Used random brand 4001 high beam headlight for the Mercury Cougar. High beam headlights are distinguished by the number 1 at 12 o'clock position and the 2 prong connection on the back. We guarantee these units to work. Basic Ford part # 13007-B.

Used random 4000 or 4002 brand low beam headlight for the Mercury Cougar. Low beam headlights are distinguished by the number 2 at 12 o'clock and the 3 prong connection on the back. We guarantee these units to work. Replaces basic Ford part # 13007-B.

*NOTE* If you're going to make your car concours correct, you need to specify which year you have (bulbs are date marked), otherwise we'll just send you any random FoMoCo bulb.Please note that we are out of date coded bulbs for 1969 and up.  If ordering online, leave the info in the comments section of your order. If your order is being done over the phone, be sure our rep knows which year you have. This is the much harder to find outer, low beam lamp distinguished by the number 2 at 12...

Sold as a pair, these were a one year only feature that allows you to quickly disconnect the hideaway headlight vacuum hose kit a few inches from the firewall. The fittings are slightly different so as not to mix up the connection by crossing the lines.

These are the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. They are held in place by a spring and two screws. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight rings side by side. If you look close at...

This is the correct ring for all years 1967 - 1973 high beam or low beam. No dings, gouges or broken spot welds. It is held in place by a spring and two screws. Four rings required per car, sold individually. Made from stainless steel, these clean up nicely with fine steel wool. Ford part number C7AZ-13015-B. Below is a comparison of the Repro and Used/NOS Headlight rings: Click on images to enlarge. The above picture shows the Used (top left), NOS (center), and Repro (bottom right) Headlight...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the 1971-73 Mercury Cougar. Marked C8OB-16A and "H", There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car. Driver side high beam bulb holder any 1971-73 Mercury Cougar.Ford part # C8OB-16A.

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7MB-17A and "LH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-17-A. Left hand high beam holder. Ford part # C7MB-17A ...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the 1971-73 Mercury Cougar. Marked C8OB-37-A and "L", There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. Driver side low beam bulb holder for any 1971-73 Mercury Cougar.Ford part # C8OB-37A. ...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-47-A and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was moved...

Used driver side (left hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7OB-47B and "LL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-47-A.  Ford part # C7OB-47B.

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-16-A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C7MB-16A and "RH", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. We have numerous 1968 numbered versions, those would be marked C8AB-16-A. Ford part # C7MB-16A.

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-17-A and "H", There are four different versions used, but they are the same for the 1969-70 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1967-68 Mercury...

Used passenger side (right hand) inner semi gloss black headlight adjusting ring that holds the headlight bulb in place of the 1971-73 Mercury Cougar. Marked C8OB-17-A and "H", There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. 1971-73 Mercury Cougar passengers side high beam bulb holder.Ford part # C8OB-17-A. ...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the Mercury Cougar. Marked C8AB-37-A and "RL", There are four different versions used, but they are the same for the 1967-68 Cougars. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. This exact same ring was also used 1969-70, but was...

Used passenger side (right hand) outer semi gloss black headlight adjusting ring that holds the headlight bulb in place of the 1971-73 Mercury Cougar. Marked C8OB-47B and "L", There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are rust free, taken from a Western parts car and are sold individually. Passenger side low beam headlight holder for any 1971-73 Mercury Cougar.Ford part...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1967-70 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. These are mostly going to have the C8AB part numbers on them, which is what we have the most of. Included is cups...

Used set of 4, semi gloss black headlight adjusting rings that hold the headlight bulbs in place on the 1971-73 Mercury Cougar. There are four different versions used. They are secured by two adjusting screws and the stainless steel headlamp retaining ring that fits over it. These are mostly rust free, taken from a Western parts cars. All four individual headlight holding cups. 

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. ALL GRADE B ACTUATORS COME WITH A 60 DAY WARRANTY. You can find the seal rebuild kit here. Used grade "B" headlight door actuator for your Mercury Cougar. Every once in a while (not often) we will...

Requires you to PRE-PAY a core charge of $30. Used grade "B" headlight door actuator for your Mercury Cougar. This grade B actuator has been reconditioned with new seals but will still slowly leak down after time as not all of them will function as new after being reconditioned. These actuators are sold individually on an exchange basis or outright (for an additional core charge). One actuator actuates both headlight doors on the 69-70. This unit also comes with a 30 day warranty. Ford part #...

This option requires you to PRE-PAY a $40 core charge. If we do not receive your core within 30 days of the original purchase, your core charge will be an in-store credit only. If your core is full of rust and debris (sounds like a tambourine) then it most likely is not a core we can give credit on. NOTE - If your actuators are the type with the internal spring (Thunderbird actuators had a failsafe internal spring) we cannot accept those as cores. An easy way to tell which actuators are the...

D0OB-13A167-A - NOT FOR COUGAR / GALAXIE. This actuator was removed from a Southern California car years ago and was immaculate inside and had no pitting on the shaft. Starting with a clean core is paramount, if it sounds like a tambourine when you start the process your results will not be very good. The inner shaft seal as well as the dust bellows was replaced using the West Coast Classic Cougar kit. It holds vacuum well on the bottom nipple, but the top (like most) will leak down in...

Pair of reproduction headlight actuators for the 67 - 68 Mercury Cougar. Manufactured to meet and exceed factory specs without the need for additional parts or modification. Keep in mind when you buy these units WCCC will pay $50 for the pair of your rebuildable core units. Our video below explains how to determine if your cores are acceptable. Check out this video on how to rebuild your existing headlight vacuum actuators ...

Used A grade, driver side or right hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our A grade housings may a minor chip, but will not have damage where the housing bolts to the car, or where the headlights mount. Fits all 1971-73 Mercury Cougar. This 1973 fiberglass driver side headlight bucket also fits 1971-72, but not vise-versa. Ford part number D3WB-13101.

Used A grade, driver side or left hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our A grade housings may a minor chip, but will not have damage where the housing bolts to the car, or where the headlights mount. Ford part number D1WB-13101.

Used Grade B driver side or left hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our B grade housings will have at least two defects, one of which will be a break where the housing mounts to the car. A bolt with over sized washers remedies these problems. Other defects could be a crack or chip in the fiberglassFord part number D3WB-13101.

Used Grade B driver side or left hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our B grade housings will have at least two defects, one of which will be a break where the housing mounts to the car. A bolt with over sized washers remedies these problems. Other defects could be a crack or chip in the fiberglass. We will often substitute the 1973 headlight housing, which was a service replacement part for 1971-72 Cougars.Ford part number D1WB-13101. ...

Used A grade, passenger side or right hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our A grade housings may a minor chip, but will not have damage where the housing bolts to the car, or where the headlights mount. Ford part number D1WB-13099.

Used grade B passenger side or right hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our B grade housings will have at least two defects, one of which will be a break where the housing mounts to the car. A bolt with over sized washers remedies these problems. Other defects could be a crack or chip in the fiberglassFord part number D3WB-13099.

Used Grade B passenger side or right hand side headlight bucket or housing. Made of fiberglass, which is fragile. Our B grade housings will have at least two defects, one of which will be a break where the housing mounts to the car. A bolt with over sized washers remedies these problems. Other defects could be a crack or chip in the fiberglass. We will often substitute the 1973 headlight housing, which was a service replacement part for 1971-72 Cougars.Ford part number D1WB-13099. ...