1970 Ford Mustang

Restored chrome automatic shifter lever for any 1969 and most 1970 Mercury Cougar or Ford Mustang with or without consoles. Sometime in the 1970 era, Ford switched to a larger pawl. Easy to identify if you look at the slit on the lever. We sell these bare for those car owners that have pitted shifter levers. Ford part number C9ZZ-7210-A. *Note - Chromed lever only, sold without cable, pawl, handle, etc. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the late version with wider width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-C. *Note - Chromed lever internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Complete chrome automatic shifter lever assembly for any 1969-73 Mercury Cougar or Ford Mustang with or without consoles. This is the early version with small width pawl. Good used part no heavy pitting on the chrome, we sell these levers with installed cable, pawl, spring, and gear release assembly. Ford part number for the lever is C9ZZ-7210-A. *Note - Chromed lever and internals only, no T handle. Check out our video on rebuilding your shifter below: ...

Lamp diffuser for all 1969-73 Mercury Cougar and Ford Mustangs. Note the comparison picture. The reproduction is a shade or two lighter than original. The complete Ford part number is not available, the basic part number for this item is 15811. Check out our video on rebuilding your shifter below: ...

Automatic shifter cable with slot on the threaded end for all 1969-73 Mercury Cougar and Ford Mustangs. Will also work on 1967-68 but features a slot at bottom so as to remove or adjust easily. The 1967-68 version did not have this slot. Ford part number C9ZZ-7D246-A with the slotted threaded stud on the end. Also fits 1971+ Maverick & Comet with automatic floor shifters. Restoration Hint - We suggest purchasing this upgraded cable for use in 1967-68 shifter levers. Much easier to install, and...

D0ZA-7E046-D Reproduction adapter plate for mounting the Hurst 4 speed shifter control assembly to the Top Loader transmission. 1970 Mercury Cougar and Ford Mustang big block 428 Cobra Jet 4 speed only. Ford master part number D0ZZ-7E046-A. Link to the expert on Ford shifter linkages. Check out our video on rebuilding your shifter below: ...

Automatic shifter arm pawl - early version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1967-70 Mercury Cougar, 1965-70 Ford Mustang, and 1965-66 Ford and Mercury full size cars with floor shift automatic transmissions. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need, this early pawl has a Ford part number...

Reproduction console shift assembly for the 69 - 73 Cougar or Mustang. Included in this kit are the T-shifter assy, lever assy, housing and the shifter arm, seals and hardware. Replaces Ford part numbers: C7ZZ-7210C C7ZZ-7A306A C7ZZ-7302A C7ZZ-7213M Check out our video on rebuilding your shifter below: ...

Excellent high quality reproduction of the automatic transmission shifter bezel / indicator assembly for the Mercury Cougar or Ford Mustang. Great savings when you consider this already has the seal and indicator lens included. Many Mustang vendors only offer the 71 - 73 plastic version of this assembly. Floor seal not included. This will also work (exact fit) on your 1971 - 1973 Mercury Cougar but will not be correct as the plastic version was used in 71-73.  This is a very nice upgrade...

New and improved design! This is a premium reproduction that features a textured skin that matches the original appearance and has a steel insert just like the originals. You can also use this on your 69 if you are using a rectangular shaft original or after market Hurst shifter on your 69.  Replaces Ford Part # D0ZZ-7277-B Cougar Applications: 1970 Mercury Cougar Check out our video on rebuilding your shifter below: ...

This 4 Speed Lower Shift Boot attaches to the bottom side of your factory Hurst shifter to protect it from water and dirt. Fits 1970 Mercury Cougar and Ford Mustang, additionally fits 1970-71 Ford Torino and Mercury Cyclone with OEM Hurst 4 speed shifters. Replaces Ford part # D0GZ-7E138-B and D0ZA-7E138-B. Check out our video on rebuilding your shifter below: ...

Leather manual shift boot for the Classic Console Cruiser Console that we offer. Check out our video on rebuilding your shifter below: ...

Bare automatic shifter bucket or housing for use with the large pawl (0.160") shifter levers. Fits most 1970 Mercury Cougar and Ford Mustangs with or without console. Check the thickness of the pawl on your shifter lever. There are two different sizes and need to be matched for optimum fit. Early pawls were 0.100" thick, sometime in early 1970 through 1973 the pawls were made larger at 0.159". We recommend purchasing new bushings prior to installation. Replaces Ford part number C9ZZ-7A306-?...

This icon means that we're looking to buy this part!WCCC is a buyer of used and NOS hard to find 67-73 Mercury Cougar parts. Usually we give an in store credit of 50% of our web price for parts delivered in hand or by carrier to our Brooks, Oregon location. If you're not interested in store credit, just shoot us an email and we will let you know if it's is something we can pay cash for. We do not send cash for parts in advance but we often can compensate you within hours of receiving the...

If your automatic floor shifter has play in it left to right then this is the culprit. Easy to install, (more difficult if you have a 67-68 with center console) these are made from a wear resistant plastic that is better than original. Sold as a pair as two are required per car. This bushing was used in all Ford products equipped with a floor shift automatic from the 1965 Mustang to the late 70's Pinto. Replaces Ford Part # C5ZZ-7A133-A Check out our video on rebuilding your shifter below: ...

Rechromed 1967 deluxe shifter button. Unique to the deluxe faux leather wrapped T handle shifter starting in 1967. One year only design, this one has a convex button for you thumb. Starting in 1968 the button was more rounded to comply with the added safety features mandated in 1968. Core deposit is required, fully refundable with returned 1967 deluxe button. Ford part number C7ZZ-7C488-B. Check out our video on rebuilding your shifter below: ...

This group of parts mounts to the top of the AT shifter arm and rides against the thumb activated button on your T shift handle. Its function is to lift the cable that runs through the chrome shifter stem to lock and unlock the shifter out of Park. The Ford technical name for this part is 'Roller - Shift Lever Lock'. We carefully inspect each part to make sure it is in perfect used condition. Ford part number C5ZZ-7D328-A. Check out our video on rebuilding your shifter below: ...

Exact reproduction for the 1969 - 1973. Perfect fit and finish. You may want to replace yours with this inexpensive unit just for the fresh new luster alone. Your plastic end buttons may have faded to gray but they were originally black like this one. Replaces Ford Part #: C8OZ-7213-A, C90Z-7213-B, D3OZ-7213-A. Check out our video on rebuilding your shifter below: ...

Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Not a very good color match for Cougar owners, but will work well with blue interiors.Stunning quality and far less likely to crack than the originals. The 67 version was actually a little different than 68 - 73 but you would have to look close to see the difference. Check out our video on rebuilding your shifter below: ...

Allen head set screw for all stock Ford automatic shifter handles on any 1967-73 Mercury Cougar or Ford including Mustang. Uses the same 3/32 inch allen wrench for attaching as the originals. Most handles take two of these set screws, one on the dummy button, and one to attach to the top of the shifter lever. The 1973 all chrome shift handle only uses one of these set screws. Original Ford part number 374985-S. Check out our video on rebuilding your shifter below: ...

Reproduction automatic shifter lever in chrome for the Mercury Cougar or Ford Mustang. Comes with inside cable parts. See the related items for more of your shifter needs. Check out our video on rebuilding your shifter below: ...

Reproduction Hurst shift lever for all 1970 and 1971 Mercury Cougar or Ford Mustang with factory installed Hurst shifters. Excellent reproduction in every way.Link to the expert on Ford shifter linkages.Click on images to enlarge. ...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The early versions used the C5ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Very nice chrome on this used shifter lever for automatic transmissions. Can fit all 1969-73 Mercury Cougar and Ford Mustangs with FMX or C-6 automatic transmissions. We have found that there is an early and a late version of these levers. The late versions used the C9ZZ-7C442-A pawl. The easiest way to determine which is early or late is the width of the slot at the bottom of the lever. If one nickel fits into the slot, it is early. Two nickels will easily fit into the later slot. Bare...

Automatic shifter arm pawl - late version. Mounts inside the bottom of the shifter arm in the slot with the cable and spring. Fits original chromed shifter levers or arms 1970-73 Mercury Cougar and Ford Mustang. The early pawl has a key with a thickness of 0.100", the later (1970ish-73) with a thickness of 0.159". Check your shift lever for the size that you need. Ford part number D0ZZ-7C442-A. Check out our video on rebuilding your shifter below: ...

Adjustable rod that connects the floor shifter to the "Select-Shift" automatic transmission. FMX transmissions only, code "X" on your door data plate tag. All 351 engines received the FMX automatic transmission. Rod with casting number D0ZA-7340-A. Shift rod approximately 18 inches long. Ford part number D0ZZ-7326-D. 1970 only. Check out our video on rebuilding your shifter below: ...

KYB Gas-a-just shocks are America's best selling performance gas shock. It's monotube design features a higher gas pressure which helps to hold the tire to road surface during severe driving conditions. N2 gas helps eliminate shock fading due to aeration and foaming. This shock is the perfect choice for the performance oriented. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.029.614.41-X- ...

These are equal in performance to other name brand high pressure gas shocks at a significant lower price. These shocks are best suited for drivers looking for firm ride with a solid controlled “feel of the road”. These units are sold individually.

This gas shock improves handling without sacrificing ride comfort. A very good choice for the daily driver wanting a smooth ride with the response of a gas shock. Also, this is the most stock-looking shock since it's black and has a flat upper collar. These units are sold individually. Manufacturer Specs: ExtendedCompressedStrokeCoverInternal StopExternal Stop14.259.334.92-X- ...

Keep in mind these will work on the Cougar but are designed for the Mustang which has a lower maximum spring travel. If your Cougar is lowered in the rear by an inch or more these will be spot on.Sold individually

This tower is technically incorrect for a 1969-70 Mercury Cougar as it has no reinforcement plate. Cougar owners would definitely want to buy a good used tower instead of this reproduction. Keep in mind all Cougars came with reinforced towers in 1969-70 just as all 1969-70 Cougars came with the 9" rear-end and 351 or larger engine.Here's a little film to help you fortify your flexxy feline! ...

1970 features a reinforcement plate that is a combination of a 1968 and 1969 plate. This is an excellent upgrade for any 67-70 Cougar or Mustang without reinforced shock towers. This is a 100% clean, uncut tower worthy of any show-car. No specific part number for this structural front suspension section. For 1970, the plate size was shortened, for easier access for spark plug changes. Generic Ford part # D0ZZ-16055-B, included apron and side member. ...

We highly suggest you look at our mint condition used towers for about the same price. This tower is technically incorrect for a 1969-70 Mercury Cougar as it has no reinforcement plate. Cougar owners would definitely want to buy a good used tower instead of this reproduction. Keep in mind all Cougars came with reinforced towers in 1969-70 just as all 1969-70 Cougars came with the 9" rear-end. All Cougars also came with 351 or larger engines for those years as well, except for the 302...

1970 features a reinforcement plate that is a combination of a 1968 and 1969 plate. This is an excellent upgrade for any 67-70 Cougar or Mustang without reinforced shock towers. This is a 100% clean, uncut tower worthy of any show-car. No specific part number for this structural front suspension section. For 1970, the plate size was shortened, for easier access for spark plug changes. Generic Ford part # D0ZZ-16054-A, included apron and side member. ...

Reproduction driver side (left hand) shock tower and apron assembly for Mercury Cougar and Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Reproduction passenger side (right hand) shock tower and apron assembly for Mercury Cougar or Ford Mustang.Here's a little film to help you fortify your flexxy feline!

Solid, undamaged, used driver side (left hand) shock tower brace for Mercury Cougar and Ford Mustangs. Consider our brace kits for the best bang for your buck! Ford part # C9ZZ-16A053-A. *NOTE* Excludes 1969-70 Boss 429.Here's our little film to help you fortify your flexxy feline!

Solid, used, and undamaged passenger side (right hand) shock tower brace for Mercury Cougar and Ford Mustang. Consider our brace kits for the best bang for your hard earned buck! Ford part # C9ZZ-16A052-A. *NOTE* Excludes 1969-70 Boss 429.

Reproduction shock tower brace nuts and bolts for Mercury Cougar and Ford Mustang.Here's our little film to help you fortify your flexxy feline!

Missing some of the hardware used to bolt on your shock tower braces? Here are our reproduction shock tower brace mounting kit for the Mercury Cougar or Ford Mustang.

Used, solid, and undamaged shock tower braces for all 1969-70 Mercury Cougar and most Ford Mustangs. Includes 4 used 7/16"-14 x 1-1/4 inch cowl attaching bolts. Ford part #s C9ZZ-16A053-A driver side (left hand), C9ZZ-16A052-A passenger side (right hand).  *NOTE* Excludes 1969-70 Boss 429. **Installation Tip** These brackets attach 'under' the cowl lip. Here's our little film to help you fortify your flexxy feline! ...

Individual reproduction shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.

Individual reproduction shock tower cap or coil spring cover in black for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. Replaces Ford part # C7ZZ-18A017-A.

Individual used shock tower cap or coil spring cover in chrome for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. While not technically restored original, we offer these to complement our chrome export braces and Monte Carlo bars.  Ford part # C7ZZ-18A017-A.

Used shock tower cap for the Mercury Cougar and Ford Mustang. These are not side specific and two are required per car. These used pieces are superior to the reproductions because they are constructed from thicker metal. Plus, you just can't beat original FoMoCo!Ford part # C7ZZ-18A017-A.

These are exact replacements for the 1964-68 Ford Mustang, but looks similar to the pans for the 1967-68 Mercury Cougar. These floor pans will also fit the 1969-73 Mustang, but the will requires modification to fit properly. 1969-70 cars have different ribbing configurations and 1971-73 cars can use these also. This is a heavy gauged stamped steel floor pan *NOTE* This floor pan has the outside lip bent up which is proper for coupes. Convertibles were bent down. You can either bend it up or...

Driver side (left hand) front seat floor pan.  This pan is cut from the full floor pans in order to save on shipping costs when a customer does not need the entire length pan. Cutting from the Dynacorn full length pans means this will be a quality cut, when compared to other pans on the market. 1967-68 style ribbing, works in 1969-70 and can be modified to fit 1971-73. *NOTE* This floor pan has the outside lip bent down which is proper for coupes, convertibles were bent up. You can either...