1970 Ford Mustang

No damage original bolt. Sold individually, two required per car.

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Have more questions about installing a...

This kit is similar to the original type mounted in every drivers side door. These OEM style Riv-Nuts will be a challenge to install unless you have the special tool. Almost every body shop will have this rivet gun type of tool but here are a couple of ways to tackle the installation without the correct tool. Hole size is 1/4". Replaces Ford Part #: C7AZ-17696. Check out our video below for more info on mirror installation: Still have riv-nut questions? Here are riv-nut answers! ...

Quick disconnect that installs between the sight glass hose and the sight glass to A/C dryer hose. This unit also includes 2 O-rings (Part # L33,D2AZ-19D695-R or YF-368 and Part # H33, D2AZ-19D695-AE or YF-316)Quick Connect (Part # QF3,C1SZ-19B696-A or YF-241 and Part # QM6, C1SZ-19B695-A or YF-252).

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

Slat or pivot bracket for attaching the #4 rear most bow on a 1969-70 convertible top. Sold individually, one for each side needed for installation. Bushing is normally broken or missing, plan on sourcing or making a replacement bushing for the pivot. Ford part number C9ZZ-7650340-A.

Reproduction power steering control valve sleeve / socket for the Mercury Cougar or Ford Mustang.

New slotted pan head screw for mounting distributor points or condensers. Three total, per single advance Ford distributors. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x9/32". Sold individually, but you likely need 3. 

New phosphate dipped slotted pan head screw for mounting distributor vacuum advances. Two total, per Ford distributor. We know that these fit FoMoCo, Autolite and Motorcraft marked distributors 1967-73. These are AMK screws 8-32x1". Sold individually, you will need 2. 

Reproduction Small Block Engine I.D. Bolt for the  1967 - 1973 Mercury Cougar / 1967 - 1973 Ford MustangSold individually 

Thermactor smog hose installation clamps. Fits all Ford and Mercury 1968 S code 390-4V or W code 427-4V engines sold in the US. Additionally fits 1968-70 428 Cobra Jet and Super Cobra Jet engines. Set of clamps, several bolts and spacer as shown. Include bolts for pump pulley, top bolt on pump for adjusting bracket, and pivot bolt and spacer for pump.

Reproduction hardware kit for installing the smog pump on cars with 390 / 427 / 428CJ engines from 1968-70. Including Cougar, Mustang, Torino, Ranchero, Cyclone, etc. Includes spacer, pivot bolt and washer, adjusting bracket bolts.

Set of thermactor smog tubes on any 1968 390GT, 1968 GT-E 427-4V, or 1968-70 428 Cobra Jet engines. Mercury Cougar and Ford Mustang, Torino, Cyclone, Ranchero, etc. These will work with original 390 or 428CJ cylinder heads drilled for air injection smog system from factory. Fits most FE engine applications that used the air pump smog system in 1968 with manual transmission. We also have the ferrules / nuts and other hardware.

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction black Holley "Sniper" fuel injection conversion carburetor for the 67 - 73 Cougar or Mustang. Upgraded Sniper II also now available! Dual Pattern bolt on carburetor replacement, designed to fit 4150 Flange & Spread Bore manifolds - (Spread Bore Sealing Plate Part #9006 is recommended)Throttle body mounted ECU – no extra boxes to mountSupports up to 650hp with Four 100 Lb/Hr InjectorsOnly 4 Wiring Connections Required! (Battery +, Battery - , Switched Ignition & RPM)Includes...

The #1 EFI conversion system just got better! Introducing Sniper 2 EFI - a self-tuning, easy-to-install, EFI conversion for common 4-barrel (4150 flange) style carburetors. Holley took everything that they learned from the original Sniper EFI system and added 14 new features that will make your EFI conversion more simple, reliable, and modern. Like all Sniper EFI systems, Sniper 2 is designed to work with the Sniper Ecosystem that includes Hyperspark ignition, complete fuel systems, multiple...

Application is for all 1970 351 Cleveland engines, both 2 barrel and 4 barrel. This air cleaner snorkel is different from past years in that the opening is necked down and has a flared flange. It also has a small opening on the bottom for a metal "S" tube. Ford part number D0OZ-9A626-D. Click on images to enlarge. ...

Applications all 1969 351 engines, both 351-2V and 351-4V, and 1970 351W-2V engines after 2/2/1970. That is correct, after Feb 1970 the H-code Windsor engined 351's used a 1969 style air cleaner snorkel.The C9OZ-9A626-B snorkel looks the same, but is a bit longer than the 1968 C8AZ-D snorkel. Probably due to the taller deck height of the 351 over the 302 engine, and or the heat shield design. Please note: Wax stat is not tested, nor can we test them, sold as- is. Click on images to enlarge. ...

Application is for the beginning of the 1970 model year and only for H-code 351W-2V. Windsor engines only, from inception until 2/2/1970. Ford part number D0OZ-9A626-B.

Quality recreation made from original parts. Decent reproduction, slightly different than the original Ford version. The noticeable difference is the lack of square notch in the slop joint. Ford part of C8OZ-9A626-C. This snorkel comes to you in primer.

For all 1968 through 1970 R and Q code 428CJ and SCJ air cleaners. Snorkel has the opposite jog than 390GT snorkels. This one jogs towards the rear of the engine. Originally this snorkel should have had an ink stamp of C8OF-9A626-A or -B. Ford MPC number C8OZ-9A626-C.

Although these are considered reproductions, they are actually put together from multiple parts of original excellent condition used snorkels. And, since there are multiple colors of Ford Blue, the supplier is leaving them as unpainted.Application would only be for 1970 Boss 302 Eliminators and Boss2 Mustangs. Ford part number D0ZZ-9A626-B.

Air cleaner pre-heater paper hose. Should fit most applications from 1970-73 Mercury Cougar and Ford Mustang with V8 engines. 2 inch inside diameter, we cut these to about 9 inches long. Correct black paper outside, flexible paper tube, kind of like a Slinky. Please verify your needed length, we leave them a bit longer than needed so that they fit more than one application.

Fits both front and rear marker light sockets. Four per vehicle. These are made so that you can splice into your harness. These solve the corroded socket and intermittent light problem.These fit the side marker lights as well as the instrument panel lights. We highly recommend converting these over to LED.Replaces Ford Part #: D0DZ-15434

This aluminum backed, tar sound deadener with adhesive is approximately 1/16 of an inch thick and works well behind door panels, at the firewall and under the headliner as a sound, heat and vapor barrier. One sheet required per door. Cut to fit, then remove paper backing to reveal adhesive, and stick in place. Comes in a 36 inch tall by 50 inch wide roll. *NOTE* Use caution when working with this product. The thin sheet of aluminum is quite sharp. We highly recommend using gloves. Before...

HushMat sound deadening and thermal insulation enhances your firewall with the easiest to install sound deadening material. Your vehicle is fun to drive, but the engine gets hot. There is over 200 degrees of heat cooking your firewall and floor pan. Your engine, headers, manifold and exhaust generate tremendous heat that transfers to the metal firewall and floor and this heats up your vehicle interior. It can create a very uncomfortable ride, especially in the summer. This also forces your AC...

Replaces Ford Part # D0ZA-A

Reproduction Space Save Tire Instructions Decal for the 1968 - 1973 Mercury Cougar / Ford Mustang

Reproduction Space Saver Spare Recall Postcard for the 1968 - 1971 Mercury Cougar / Ford Mustang

Aluminum spacer used on 289/302/351 engines for mounting the alternator. Length is 1-5/8 inches long, mounts between the alternator and the cylinder head.

Alternator spacer bracket for all 351 engines. 1970-73 Mercury Cougar and Ford Mustang among others such as Torino, Cyclone, Galaxie, LTD, etc. Aluminum material, 2-1/4 inches long, with a 7/16" hole. Sometimes solid and sometimes open along the side. Ford part number D0OZ-10A370-A.

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.

Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. New manufactured.

B8AZ-6359-A Crankshaft or dampener spacer for any FE Ford engine. 1965 - 1971 Ford or Mercury crankshaft spacer 352, 390, 427, 428, all FE engines. Used spacer, will show a little wear from the outside seal. 

Used spacer that fits inside your seat belt buckle and serves as a stop for when you assemble the metal buckle into the face plate/bezel. Installation is as shown in the pictures above.  Sold individually, one per buckle.

Reproduction 384543-S8 Power steering pump adjusting spacer for use without air conditioning. For most 1970 - 1973 Mercury Cougar or Ford Mustang with 351C engines. Spacer dimensions: 7/16" I.D. and 1/2" thick.*Note 1970 and later cars with 302 or 351W engines use a 3/4 inch spacer.

Reproduction 384542-S2 Power steering pump adjusting spacer for use without air conditioning. For all 1970 and later Mercury Cougar or Ford Mustang with 302 or 351W engines. Spacer dimensions: 7/16" I.D. and 3/4" thick.*Note - 351C engines use a 1/2 inch spacer.

Reproduction  Lower Windshield Moulding Center Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Used spacer for the lower windshield moulding

Reproduction  Lower Windshield Moulding Fender Spacer for the 1969 1970 Mercury Cougar or Ford Mustang  

Replacement disc brake pedal mounting spacer. Correct diameter and length for installing disc brake pedals 1967-73 Mercury Cougar and Ford Mustang. About 2-1/8 inches long, correct I.D. and O.D. made from Moly steel. Basic Ford part number 2A188, the correct Mustang / Cougar number has been obsolete in the Ford MPC's for years.

Reproduction shoulder belt bolt spacer for the 69 - 73 Cougar or Mustang. Does not have markings like the originals. One per side, two per car.

One per side, 1968 does not use the triangle markings. The letter "D" stamping was in place to aid line workers with correct placement on the car.

We claim that in time every nut bolt and clip will be documented on this site! Here is yet another tiny little, one year only trivial part that only the most detailed enthusiast will even care about. This little part is designed to space the column cover away from the metal lower dash so as to prevent dash squeaks. They are left natural, never painted (the one shown has surface rust). Two are required per car, they are sold individually. These little parts are often missing and of course not...

Reproduction engine block spacer plate for 1969 1970 351 engines FMX (code X) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too.  Replaces Ford part number D0AZ-7007-A.

Factory engine block spacer plate for 1969 1970 351W and 351C engines FMX (code X) and C6 (code U) transmissions. According to the Master Parts Catalog, it also fits 164 tooth bellhousings on 1968-70 with 302 engines too. We also stock the early version from 1968 and 157 tooth versions. There are probably two versions of this plate, we believe the the 1969 version did not have the indentations. Replaces Ford part number D0AZ-7007-A.