Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 1-48 of 169
$0 Price: $653.85

Buy Details

Availability: Ships Direct from Supplier (Except International)
Item #: 17763 -

Exact Reproduction 289 Hi-Po Main Cap Set offered by Ford. They are cast and machined here in the USA from the original Ford blueprints. A set consists of caps numbered 1- 4 and requires the use of an original rear main cap to finish an engine. These caps are cast from the highest quality Nodular iron and machined for ease of fitting to any 289 block. The I.D. of the main bearing bore is .020 undersize and the side registers are .010 oversize on each side for proper adjustment before line...

$0 Price: $18.23

Buy Details

Availability: In-Stock Item
Item #: 41663 -

Cork Oil Pan Gasket for the 351 Cleveland Cork Oil Pan Gasket in the 1970, 1971, 1972 and 1973 Mercury Cougar or Ford Mustang.

$0 Price: $12.47

Buy Details

Availability: In-Stock Item
Item #: 41854 -

Spark Plug Wire Separator Brackets for the 1969 - 1970 Mustang Cougar or Torino with 428CJ Finned Aluminum Valve Covers, 1969 - 1970 Mustang Boss 302 with Finned Aluminum Valve Covers or Boss 351 models. These are an MCA approved unit made here in the USA. These replace Ford part number C9ZZ-6583-A and include both brackets and the 4 screws to properly install these units. Attaches spark plug wire holder to the factory finned aluminum valve covers

$0 Price: $755.80

Buy Details

Availability: In-Stock Item
Item #: 12136 -

Quality reproduction of the 1968 - 1970 CJ Mercury Cougar, 1969 - 1970 Shelby GT500, 1968 - 1969 Cyclone, Ford Fairlane, Ranchero and Torino 428 Cobra Jet Ram Air cleaner base. Features correct snorkel opening and breather elbow.Replaces Ford part number C9ZZ-9600-E or C8ZZ-9600-A.

$0 Price: $5.85

Buy Details

Availability: Out of Stock
Item #: 26359 -

This is a reproduction of the original white engine displacement decal with a blue background Powered by Ford (logo) followed by 351-4V Regular Fuel followed by white background with blue lettering and a Motorcraft, Autolite parts logo. located on the top of the air cleaner. *Note - Too small to fit the 18 inch diameter air cleaner lid from 1968-72.Fits the following models with a 351 4 barrel engine:1974 Cougar1974 Mustang

$0 Price: $8.25

Buy Details

Availability: In-Stock Item
Item #: 26339 -

This is a reproduction of the original chrome engine displacement decal with black lettering and stripes that was located on the top of the air cleaner.Fits a 1967 Mercury Comet GT with a 390 4 barrel engine.This decal is for the 1967 Mercury Comet 390 4V GT Air Cleaner. It can be used on the Cougar but as far as we can tell the 67 390 GT Mercury Cougar did not have an air cleaner decal.

$0 Price: $18.18

Buy Details

Availability: In-Stock Item
Item #: 33003 -

Blue reproduction pressure relief valve plug, for the Thermactor Smog Pump. The correct smog pump should have a relief valve and this is the pressure setting plug that goes into the valve on those 1968-71 smog pumps. 1968 manual transmission cars all engines, Holley carburetor equipped cars 1968-71.

$0 Price: $12.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 27541 -

Used bolt and washer for attaching the crankshaft balancer or damper to the crank shaft. 15/16 inch hex head with 5/8-18 threads and 1.75 inches long. Basically fits all Mercury Cougar engines except the 1971 429 Cobra Jets engines. Fits 1967-73 289, 302, Boss 302, 351W, 351C, 390, 427, and 428CJ engines.Torque specifications for this bolt are 70-90 foot pounds.*Note does not fit 429 or 460 V8 engines or any 6 cylinder engines.

$0 Price: $6.85

Buy Details

Availability: In-Stock Item
Item #: 32393 -

Bolt kit for installing the idler and adjusting pulley on any 1968-69 Mercury Cougar / 1968-69 Ford Mustang or 1968-69 Ford / Mercury with small block 289 / 302 / 351W engines. 4 bolts 3/8-16x7/8 inch washer head bolts.  

$0 Price: $7.85

Buy Details

Availability: In-Stock Item
Item #: 32392 -

Bolt kit for installing the idler and adjusting pulley on any 1970-73 Mercury Cougar / 1970-73 Ford Mustang or 1970-73 Ford / Mercury with 302, 351W, and 351C engines. 4 bolts 3/8-16x7/8 inch washer head bolts and 1 thick 3/8 washer.  

$0 Price: $7.65

Buy Details

Availability: In-Stock Item
Item #: 32391 -

Bolt kit for installing the idler and adjusting pulley on any 1968-70 Mercury Cougar / 1968-70 Ford Mustang or 1968-70 Ford / Mercury with 390, 428CJ engines. 4 bolts 3/8-16x7/8 inch washer head bolts and 2 thick 3/8 washers.  

$0 Price: $6.85

Buy Details

Availability: In-Stock Item
Item #: 32394 -

Bolt kit for installing the idler and adjusting pulley on any 1970-71 Ford Torino / Mercury Cyclone, or 1971 Mercury Cougar / Ford Mustang with 429/429CJ engines. 4 bolts 3/8-16x7/8 inch washer head bolts.  

$0 Price: $30.96

Buy Details

Availability: In-Stock Item
Item #: 31055 -

Oil pan bolt kit for all FE 390, 427, and 428 engines. Set is made by AMK and includes 20 OEM style bolts and washers. We sell them specifically for 1967-70 Mercury Cougar and Ford Mustang, but they will fit most all Ford "FE" engines including 352, 410, and 360 Ford engines. If you happen to have a 428CJ with windage tray, we also offer a set of bolts for that application too. ...

$0 Price: $26.35

Buy Details

Availability: In-Stock Item
Item #: 31056 -

Oil pan bolt kit for all 428 Cobra Jet and 428 Super Cobra Jet engines with windage tray. Set is made by AMK and includes 20 OEM style bolts and washers. 

$0 Price: $33.25

Buy Details

Availability: In-Stock Item
Item #: 31566 -

New Bolt kit, for the installation of a water pump on 1970-73 Ford 302, Boss 302, or 351W engine. Fits all 1970 Mercury Cougar and 1970-73 Ford Mustangs. 9 total pieces in the kit as shown.

$0 Price: $33.25

Buy Details

Availability: In-Stock Item
Item #: 31569 -

New Bolt kit, for the installation of a water pump on any Ford 351C or 351 Cleveland engine. Fits all 1970-74 Mercury Cougar and Ford Mustang with 351C, 351CJ engines. 11 total pieces in the kit as shown.

$0 Price: $9.25

Buy Details

Availability: In-Stock Item
Item #: 13685 -

New Bolt kit, for the installation of a water pump on any Ford 352, 390, or 428CJ engine. Fits all 1967-70 Mercury Cougar and Ford Mustang with 390-4V, 390-2V, and 428 Cobra Jet engines.

$0 Price: $27.49

Buy Details

Availability: In-Stock Item
Item #: 41411 -

Set of 12 bolts for the intake manifold on any factory 1966-67 Ford 289 engine. AMK F-478.*Note - Excludes 1968 289 and 302 engines.

$0 Price: $41.27

Buy Details

Availability: In-Stock Item
Item #: 25913 -

Set of (12) 2 1/16" bolts / studs and nuts for the intake manifold on any factory 1968 Ford 289 or 302 engine. AMK F-479. *Note - Excludes 1967 289 engines.

$0 Price: $37.80

Buy Details

Availability: In-Stock Item
Item #: 25908 -

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-2V engine. AMK F-1313.*Note - Excludes 351C-4V and 351W engines.

$0 Price: $33.25

Buy Details

Availability: In-Stock Item
Item #: 14281 -

Set of 12 bolts for the intake manifold on any factory 1970-74 Ford 351C-4V engine. AMK F-1321.*Note - Excludes 351C-2V and 351W engines.

$0 Price: $33.03

Buy Details

Availability: In-Stock Item
Item #: 12488 -

Set of 16 bolts for the intake manifold on any factory 1969-70 Ford 351W-2V and 351W-4V engine. AMK F-1131.*Note - Excludes all 351 Cleveland engines.

$0 Price: $43.53

Buy Details

Availability: In-Stock Item
Item #: 11996 -

Set of 10 bolts and several spacers for the intake manifold on any factory 1967 Ford S or Z code, 390 engine. AMK F-475.*Note - Excludes 1968 1969 1970 - 390 and 428CJ engines.

$0 Price: $44.37

Buy Details

Availability: In-Stock Item
Item #: 11273 -

Set of 12 bolts / spacers / stud for the intake manifold on any factory 1969-70 Ford S code 390-4V or 428 Cobra Jet or 428SCJ engine. AMK F-475.*Note - Excludes 1967-68 390 engines.

$0 Price: $41.25

Buy Details

Availability: In-Stock Item
Item #: 80222 -

Set of bolts and studs for the intake manifold on any 1970 Ford 428 Cobra Jet engine. The 1970 set includes a second double ended stud, while the 1969 set only includes 1 double stud. 1970 R and Q code Mustang and Cougar.Trivia - 1970 Mercury Cougars only have a Q as the 5th digit in the VIN code. Yes, All 1970 428 cobra jet Cougars are designated as Q codes. Ram air was optional and will show on the window sticker or Marti Report.

$0 Price: $47.35

Buy Details

Availability: In-Stock Item
Item #: 53276 -

Set of 20 bolts for the intake manifold on any 1970-71 Ford 429 Cobra Jet engine. 429CJ engines were optional in only in 1971 on Mercury Cougar and Ford Mustangs. Available in 1970 on B body Torino, Cyclone, Ranchero, Fairlane. *Note - Excludes Boss 429 engines.

$0 Price: $26.87

Buy Details

Availability: In-Stock Item
Item #: 22631 -

New reproduction of Ford part number D0OZ-9S500-A, Hi Temperature choke gasket for all 1970-71 429 Cobra Jet engines. Must utilize the stock Ford cast iron 429 Cobra Jet intake manifold. Fits J and C code 1971 Mercury Cougar and Ford Mustang, and J and C code 1970-71 Ford Torino, Ford Ranchero, Mercury Cyclone.*Note - Excludes 429 Super Cobra Jet engines which used a different intake manifold.

$0 Price: $39.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22234 -

Used cast iron choke stove from any 1970-73 351C-2V Ford engine. This is held on with 4 bolts, and to our knowledge no block off plate is reproduced. Casting number on the iron plate is D0AE-9A705-D, which is only for the plate. The plate and coiled tube assembly has a Ford part number of D0AZ-9C869-B. No hardware included.

$0 Price: $115.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 22235 -

Used cast iron choke stove from any 1970 351C-4V Ford engine. This is held on with 2 bolts. Casting number on the iron plate is D0AE-9A705-C, which is only for the plate. The plate and tube assembly has a Ford part number of D0AZ-9C869-A. No hardware included. Limited to stock on hand.* Note - for those who do not need the choke stove, a cast aluminum block off plate can be purchased through Summit.

$0 Price: $19.00

Buy Details

Availability: In-Stock Item
Item #: 33631 -

Used Wittek #88 clamp. Originally was Zinc Dichromate plated. This used clamp was used for attaching the air inlet filter assembly to the inlet bracket. 1966-67 Ford and Mercury cars and light trucks with Thermactor smog systems. Typically found on California sold vehiclesWittek manufactured their part number is 88 and it is stamped as such. The Ford part number is 97289-S. This information was found in the 1967 Engine Assembly Manual.

$0 Price: $19.00

Buy Details

Availability: In-Stock Item
Item #: 33632 -

Used Wittek #92 clamp. Originally was Zinc Dichromate plated. This used clamp was used for attaching the air inlet filter assembly to the inlet bracket. 1966-67 Ford and Mercury cars and light trucks with Thermactor smog systems. Typically found on California sold vehicles. There is also a Wittek 88 clamp, which is slightly smaller. Wittek manufactured their part number is 92 and it is stamped as such. The Ford part number may be 97289-S. This information was found in the 1967 Engine...

$0 Price: $4.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30135 -

Used distributor clamp with bolt, for any 260 / 289 / 302 / 351W / 351C / 429CJ built from 1963-1973. May come with either an original used bolt or the new bolt made by AMK Products. Ford part number C3AZ-12270-A.

$0 Price: $71.85

Buy Details

Availability: In-Stock Item
Item #: 10304 -

Reproduction thermal fan clutch that fits 1967 - 68 289 engines, 1968 302/390/427/428CJ engines, and 1969 351W engines, all with original Ford thermal cooling fans. Slightly larger in overall diameter, (still fits fine), and retains the correct spacing from radiator. We know that these will fit Mercury Cougar and Ford Mustangs 1967-69. Closest reproduction fan clutch on the market that fits the original and reproduction C8OE-B 7 blade power fan. Hayden fan clutch with an overall height of 2.98...

MSRP:$263.99
$263.99 Price: $224.87

Buy Details

Availability: In-Stock Item
Item #: 10574 -

Spot-On reproduction from WCCC! C8OE-B Application for 1968 includes all 390-2V, 390-4V, 427-4V, and 428 Cobra Jet engines with and without air conditioning. 1969 application is only the S code 390-4V engine, with or without air conditioning. Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C8OZ-8600-A. This fan will also work on many small block applications. We hope...

MSRP:$263.99
$263.99 Price: $224.87

Buy Details

Availability: In-Stock Item
Item #: 10575 -

Another spot-on reproduction by WCCC! C9ZE-E Applications: 1. All 1969 428 Cobra Jet with and without air conditioning. 2. 1969 428 Super Cobra Jet with V code 3.91 axles only. 3. 1970 428CJ with air conditioning and some without air conditioning (see your build sheet if available). Fan description - 7 blades and 18-1/4 inches in diameter. Fan does not include thermal fan clutch. We do sell a Hayden replacement fan clutch. Replaces Ford master part number C9ZZ-8600-C. This fan will...

$0 Price: $79.97

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 30252 -

Hot idle compensator valve assembly for many Ford engines with PCV, starting in 1964 through early 1968. Typically found on 1964-66 Ford 260-2V, and 289-2 engines with air conditioning. 1967-68 289-2V, 302-2V and some 390 engines all with air conditioning and PCV or closed emissions. The Ford assembly manual indicates that the Hot Idle Compensator Valve 'T' Assembly, was installed by removing 3/4 inches of the PCV hose, 2-1/4 inches (on center of the PCV valve). See picture for clarification....

$0 Price: $65.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33437 -

C7AE-D, Fan description - 5 blades and 18 inches in diameter. Ford master part number C7AE-8600-D. These 5 blade flex fans usually came on full sized Ford and Mercury cars starting in 1967. Can be used on any engine with the proper spacer with fan shroud with adequate fan opening. Check out this interesting video where they test the efficiency of factory style and aftermarket fans. Spoiler alert: the clutch fans are the most efficient! ...

$0 Price: $44.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31181 -

Crankshaft oil slinger for all small block Ford V-8's, starting 1963 until at least through 1973. 1963-68 289 and 289 HiPo engines. 1968-73 302 engines, 1969-70 Boss 302 engines, 1969-73 351W engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines. Outside diameter about 2-7/8 inches. Ford part number C3OZ-6310-A.

$0 Price: $44.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 31183 -

Crankshaft oil slinger for all 351C or Cleveland engines. Goes on the crankshaft after the timing gear and before the timing chain cover. It does have a purpose on the vintage engines.  Ford part number D0AZ-6310-A.

$0 Price: $235.04

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 16122 -

Single cylinder head from 1972 Mercury Cougar with Q code 351C-4V engines. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.19 and 1.71 inch valves, and the chambers measure out at 75.4 cc's. These are considered 'Open Chamber Heads'. With stock pistons, these heads will net an approximate compression ration of 8.6:1. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D1ZE-6090-GA. 4V in...

$0 Price: $169.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 13465 -

Single cylinder head from 1969 Mercury Cougar H or M code 351W engines, 351-2V and 351-4V all the same. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common C9OE-6090-A.These weigh 53 lbs. each, and cannot be combined with other items unless shipping truck freight. ...

$0 Price: $89.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 18866 -

Single cylinder head from 1970 Mercury Cougar H code 351W engines, 351-2V. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 1.84 and 1.54 inch valves, and the chambers measure out at 60-62 cc's. Basic cylinder head number is 6090. Several Ford casting numbers were used, including the common D0OE-6090-C. 1970 351 Windsor engine, not to be confused with the 351 Cleveland engine from the same year.These weigh 53 lbs. each, and cannot be...

$0 Price: $285.00

Buy Details

Availability: Out of Stock
Item #: 33014 -

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped holes for exhaust manifolds. These weigh 48 lbs. each, and cannot be combined with other items...

$0 Price: $225.00

Buy Details

Availability: Discontinued, Limited Stock on Hand
Item #: 16746 -

Single cylinder head from either a 1968 X code 390-2V or 1969 Mercury Cougar with 390-4V or 390-IP engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1 (9.5:1 with X code). Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes....

$0 Price: $285.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33013 -

Single cylinder head from 1966 Ford with 390-4V engine. Sold as a core, needs thorough cleaning and rebuilding prior to use. These cylinder heads are factory drilled and tapped for thermactos smog tubes. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust...

$0 Price: $350.00

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 16158 -

Single cylinder head from 1967 Mercury Cougar with 390-4V engine with California thermactor smog ports. Sold as a core, needs thorough cleaning and rebuilding prior to use. Typically this cylinder head has 2.02 and 1.55 inch valves, and the chambers measure out at 71-74cc's. With stock pistons, these heads will net an approximate compression ration of 10.5:1. Basic cylinder head number is 6090. This is a GT cylinder head with 14 drilled and tapped exhaust bolt holes. Current...

$0 Price: $6.45

Buy Details

Availability: In-Stock Item
Item #: 13913 -

Reproduction rubber seal for the top of the brake fluid reservoir on the drum brake equipped Mercury Cougar or Ford Mustang. Also fits 1967-71 Ford or Mercury full and mid sized cars, and 1970-73 Maverick and Comet.  Replaces Ford part # C9AZ-2167-B.

  • < Prev