Steering

Reservoir Attaching Nut 351335-S38 - Used Nuts for attaching the oil reservoir to the pump. The larger of the two nuts goes against the can. Threads of 5/8"-18 to fit the high pressure port. This is a pair of nuts, one tall and one short. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, except for 1970 with 351 engine, and Mustang with 302 engines. 1970 302 / 351 engines used a different pump with an offset...

Used flat headed stove bolt and nut, for attaching the two steering column mounting brackets together. Brackets for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Two needed per installation, sold individually. This is a 3/8-16 square neck bolt and nut. Ford part number 384527-S2.

Used bracket for mounting a steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Main bracket only, there is also a side support bracket that is also needed. Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick. Tilt and fixed steering columns.Ford part number D0AZ-3676-A.

Used bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Main bracket only, there is also a hooped support bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3676-A.

New reproduction of the grommet found at the bottom of nearly any Ford steering column starting in 1970 for the transmission lockout rod. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Reproduction upper tube lower insulator for the 1968 Cougar or Mustang column. Used to stabilize the lower end of the steering column. Works on both tilt and fixed columns. Outside diameter is 2-1/8" inches and inside diameter is 1-1/2" inches. NOTE* Ford describes this as an "upper" bearing in relation to the lower steering column tube bearing. It is not used at the upper end of the column.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a...

Reproduction Headlight / Tilt Column Vacuum Check Valve for the 1967 to 1973 Mercury Cougar, Cyclone, Marquis, Ford Torino, Ranchero, Galaxie, LTD, Thunderbird, Lincoln Continental and Mark III. NOTE: The direction of flow is up through the dual ports and out through the single port.  For more in depth detail on this reproduction, see pictures below. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've...

If you have already begun to install or have installed this item, it is not eligible for return or refund. This rim blow horn switch is made in the United States by Daniel Carpenter Mustang and is made from vinyl like original. When installing, make sure to massage the rim blow switch in place with counter clockwise, compacting strokes. Clockwise strokes (thumb motions) will stretch the switch and when you complete the installation you will find the part has become too long to fit in place...

New foam insulation for the lower tube of the steering columns. Can be used on fixed and tilt columns, from 1968-73, on all Mercury Cougars, Ford Mustangs, and most all other Ford steering columns with a lower tube with inside diameter of 1-5/8 inches. The originals have almost always disintegrated. Adhesive probably isn't needed, but we recommend just a little drop of something to hold it in place. This is a dense foam insulation ring. DIY guys, this material can be found in bulk at home...

Locking pawl cable assembly for 67 - 69 TILT column T-Birds.

Locking pawl pin for your 70 - 79 tilt steering column for all Lincoln - Mercury - Ford products. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to your locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to this part can avoid several hundred dollars in damage. This precision...

Locking pawl catch pin and locking pawl pin for your 70-73 Lincoln - Mercury - Ford tilt steering columns. This is an improved reproduction with cir-clips to prevent movement, avoiding damage to you locking pawl. These shafts are notorious for working their way out of place with normal use. Once the pin works its way out the locking pawl will not be aligned with the teeth and the cast part will break under pressure. Upgrading to these parts can avoid several hundred dollars in damage. These...

Shrink-on plastic sleeve that is found on the lower part of the collapsible steering columns. Used sleeves are often ripped and torn. Simply cut off your old sleeve and install this item to give your column a newer look and feel. Installation: Make sure that your column is clean. Lube the column and inside of the sleeve. Do not remove the crease on the plastic, you need it to help you put the sleeve on the tube. Push the sleeve on as far as you can. Gently tap the sleeve down on a table top...

Used power steering oil cooler for many 1971-73 Ford, Lincoln and Mercury cars with air conditioning. Specifically these came from 1971-73 Mercury Cougar or Ford Mustangs with factory installed air conditioning and power steering. This unit mounts to the top of the A/C compressor. This installs inline with the low pressure return hose.  Manufactured by the Blissfield Company and has a Ford stamped number of D1AA-3D746-AB. The Ford engineering number is D1AZ-3D746-D. 

Used Release Spring for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Used Spring Sleeve Cap for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang 

This is the closed cell foam cover for your power steering lines to keep them from getting scuffed, and they repel oil quite well too. These are always disintegrating on the older cars and need replacement after 40 years of service. this line length can be cut to fit easily on a split line like the Cougar. Good for Cougar, Comet, Mustang, Montego, Torino, Cylone, Maverick and Ranchero.Measures 21" long

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1970-71 Mercury Cougar or Ford Mustang. Support bracket only, there is also a large support bracket that is also needed. Tilt and fixed steering columns.Bracket also used on 1970 full sized Ford and Mercury cars, and 1970-71 Ford Maverick.  Ford part number D0ZZ-3B139-A.

Used lateral or side bracket for mounting the steering column to the instrument panel on any 1972-73 Mercury Cougar or Ford Mustang. Hooped support bracket only, there is also a large main bracket that is also needed. Tilt and fixed steering columns. Bracket also used on 1971 full sized Ford and Mercury cars.  Ford part number D1AZ-3B139-A.

If you have already begun to install or have installed this item, it is not eligible for return or refund. This is far superior to the switch Ford put out as a service part in the 90's. It is imperative that you clean every part of your old switch out before carefully installing the new switch. It is best to start both ends at the same time at 6 o'clock and meet at the middle at 12 o'clock. It measures 44" in length. We've found that these switches are about an inch too long, so you'll...

For two spoke steering wheel. Two pressure switches with connection terminals installed into black plastic holder. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part # D2AZ-13875. Fits standard or deluxe steering wheel inserts.

Unlike the reproduction, we have this available in multiple colors. Call for availability. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Ford part # D1ZZ-13915-A Used in conjunction with the deluxe trim plate.

For two spoke steering wheel, comes in black only. Exact reproduction with correct grain texture. Fits 1970, 1971, 1972, and 1973 Mercury Cougar. Replaces Ford part #D0ZZ-13915.

New blue removable strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

New red permanent strength thread locker for your project. This is a must have item if you are reassembling your pride and joy after restoration or just changing out parts. Often times, the vibrations from these antiques can vibrate loose the fasteners used to hold it together. If you use this, you can rest assured that your Merc or Ford will not fall apart from fasteners that have vibrated loose.

Reproduction steering gear or seat belt washer for the Mercury Cougar or Ford Mustang. These units are sold individually.Replaces Ford part # 378580-S.

This is the part of the tilt switch that the turn signal wand screws into. This part is always included when you purchase a new turn signal switch. 1967-69 mechanism has two springs on either side, the 1970-73 mechanism uses just one spring. There is an active thread on the Classic Cougar Community Forum discussing tilt columns and trouble shooting. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many...

C6AA-3D746-A Oil cooler used on all 1968 Shelby Mustangs with power steering. Both GT-350 and GT-500 models. www.thecoralsnake.com/TRIVIA.HTML 2-3 items down.

Used pitman arm for any 1966-69 Mercury Cyclone or Ford Ranchero / Torino with power steering. Has casting number C6OA-3590-D.

NOS retainer / friction clips that replace broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper piece of this shaft...

D0AZ-3C511-F Steel bracket that mounts to the engine block for adjusting the power steering pump. For any 1971 Cougar and Mustang with 429CJ engines with or without air conditioning. Additionally this bracket fits 1970 - 1971 Torino / Cyclone / Ranchero with 429CJ engines. *Note - Must be used in conjunction with the D0AZ-3A732-A pump bracket.