Bumpers & Trim

These retainer clips work for both the windshield and rear window stainless steel mouldings. These are often times rusty so when you are replacing your seal or trim be prepared to replace a few if not all of them. See chart below to determine how many you need for your application. Replaces Ford Part # :C5ZZ-6542413-C, C5ZZ-65423A26-B or C5ZZ-6543413-B. Sold Individually. We recommend buying the box of 100 clips to be certain you have enough clips with plenty to spare. You'll also save...

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission. Replaces Ford part number C4ZB-17450-C.

This clip mounts the actuator shaft to the eyelids. Two required for 1967 - 1968, one required for 1969 - 1970. Same clip holds the windshield wiper motor to the wiper transmission.

Reproduction metal rear deck / trunk lid moulding / trim clip for the Mercury Cougar. This clip comes with a correct looking nut and works with the 1967-68 aluminum trim and the 1969-70 stainless steel trim. This unit measures about 1-7/8" long with a stud height of about 3/4". 7 clips needed per trunk lid. Note that this clip features a stud that is a little longer than what was factory. If you have a swollen lip (rust) on your deck this will be an advantage to you, if not you will have to...

Reproduction aluminum shift indicator console overlay for the Mercury Cougar or Ford Mustang. Although a brushed finish is correct, this reproduction has a coarser brush stroke when compared to the originals and is a bit dull.  We recommend a quick polish to make them look closer to the finish of the originals. These fit well, and unless you put them up against an original, it is hard to tell the finish is slightly different. This installs around your console...

We have a hard time finding and keeping grade A "near mint" front fillers on our shelves. Driver side (left hand) part number is C7WY-16304-B and the casting (or engineering) number imprinted on the part is C7WB-17B957-B. The Mercury MPC refers to these as "anti squeak pads." Sold individually, not as a pair.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need...

This is the grade “B” driver side (left hand) front bumper corner filer and is what we find on the majority of our parts cars. These used hard rubber parts will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch. Steel wool is a good way to clean them up and boiling them in water before install can often times make them appear less warped. These look better than the reproductions in our opinion and will cost you less money. Driver side part number...

We have a hard time finding and keeping grade A "near mint" front fillers on our shelves. Passenger side (right hand) part number is C7WY-16304-A and the casting (or engineering) number imprinted on the part is C7WB-17B951-B. The Mercury MPC refers to these as "anti squeak pads." Normal 0 false false false EN-US X-NONE X-NONE Sold individually, not as a pair.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be...

This is the grade “B” passenger side (right hand) front bumper filler and is what we find on the majority of our parts cars. These used hard rubber parts will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch. Steel wool is a good way to clean them up and boiling them in water before install can often times make them appear less warped. These look better than the reproductions in our opinion and will cost you less money. Passenger side part number...

Far better quality than the reproductions. The driver side (left hand) has a C7WY-16304-C Ford part number and the casting (or engineering) number imprinted on the top of the driver side part is C7WB-17B957-A. The Mercury MPC refers to these as "anti squeak pads." Sold individually, not as a pair*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need cleaning. Sold...

Sold individually. This grade "B" filler is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch, maybe even a factory blem has been found that will drop it to a grade "B" level. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This (albeit less than perfect) looks better than the reproduction in...

Far better quality than the reproductions. The passenger side (right hand) has a C7WY-16304-D Ford part number and the casting (or engineering) number imprinted on the top of the passenger side part is C7WB-17B951-A. The Mercury MPC refers to these as "anti squeak pads." Normal 0 false false false EN-US X-NONE X-NONE *NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The part you will receive will be "as taken from a parts car" and will need...

Sold individually. This grade "B" filler is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped or have a visible scratch, maybe even a factory blem has been found that will drop it to a grade "B" level. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This (albeit less than perfect) looks better than the reproduction in...

Reproduction pair of rubber front bumper corner fillers for your 1967 - 1968 Mercury Cougar. These install horizontally in the upper portion of your front bumper corners. Good used originals have become very hard to come by and that's why we've partnered with Daniel Carpenter to make these high quality reproductions. Do not confuse these with the previous inferior reproductions from a different supplier. Sold as a pair. Replaces Ford part #'s C7WB-17B951-B and C7WB-17B957-B ...

Reproduction pair of rear bumper corner fillers for the 67 - 68 Cougar. The Mercury MPC refers to these as "anti squeak pads."  Replaces Ford part numbers: Driver side - C7WY-16304-C                                            Passenger Side - C7WY-16304-D

This 2 1/4" trim part installs directly above the steering column.

When removing this part resist the temptation to "open it up". Instead walk it off carefully leaving it in its factory position.

This unique to 1967 standard Cougar dash trim set is what outlines the gauge cluster face pad. It is unique to the 1967 standard Cougar as it is held in place by black Phillips Screws. The 1968 trim set is held in by clips. Please note that AC cars have a unique design in that the long lower trim has a cut out for the AC vent.

Used aluminum face pad moulding / trim four piece set for the Mercury Cougar.

This trim part starts to the upper left of the gauge cluster and continues on to the passenger side following the line of the upper padded dash.

Only for use on standard model Cougars with no A/C. This piece of trim affixes to the lower portion of the dash face pad and continues on towards the passenger side door.

Used dash face pad for the standard Mercury Cougar that is NOT equipped with air conditioning. This unit will be nice and will not have any cracks, but could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a different color, find your local autobody supplier. They should be able to mix up a small amount of the exact color you need. This icon means that we're looking to buy...

Used grade B dash face pad for the standard Mercury Cougar that is NOT equipped with air conditioning. This unit will be nice but will have at least one small crack or crease, usually right in the middle. Give us a call to check availability and to find out if we have the color you're looking for. As usual, this pad could use a reproduction emblem and a coat of good vinyl paint to make it look great. We recommend SEM brand vinyl paint, you can get black here or parchment here. If you need a...

Reproduction Center Grille Insert Background Decal for the 1967 and 1968 Mercury Cougar. This insert will need to be shaved down on 2 sides to fit correctly, do not force the insert into the grille, it will pooch up in the middle and not adhere correctly. The aluminum Mercury Man emblem can be popped out from the rear with a solid hit with a drift punch and hammer without causing damage. Check out our video, showing how to install this decal, along with some other handy grille restoration tips ...

This restored trim piece mounts to the back of the vent frame of any 1967-68 Mercury Cougar or Ford Mustang. Passenger side only, made of galvanized steel. Full part name by Ford is: Retainer, vent window division bar glass run. The felt inserts will generally not be serviceable. See also C7ZZ-21546-A. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration ...

Used driver side (left hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

Used passenger side (right hand) factory stainless steel door guard for the Mercury Cougar.NOTE: This item will not ship until a useable core is received.

Stainless steel clip on guards for the rear edge of the 1967 and 1968 Cougar doors. Would have been part of the exterior deccor option. Self attaching, no adhesive or screws needed. Specifically contoured to the Cougar door edge. These used trim parts will have many very small dings and scratches. The driver side moulding will have substantially more damage than the passenger side moulding. Ford part number C7WY-6220910-A. NOTE: This item will not ship until useable cores are received. ...

C7ZZ-652220-B Restored, stainless steel "L" shaped top frame for 1967-68 Mercury Cougar and Ford Mustang Hardtops. Passenger side only, there is a slight curvature which make these side specific. When these are taken apart, the rubber channel section falls apart during removal, keep this in mind. *Note - Excludes Mustang fastback and convertible.

If you do not have a core that is worthy of restoration we have them for sale.Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

This conversion will replace the old, tired, vacuum system that likes to leak and wear out. This kit consists of two electric actuator assemblies (new Mazda Miata motor) with a plug and play wiring loom for easy installation. Simply remove all existing vacuum components and replace with this kit to have headlight covers that work under any conditions with the car running or not. These new motors are smoother and more reliable than previous versions that utilized the Ford Probe motors and are...

This is a very nice reproduction that we have all needed for many years! You might want to buy a new Cougar walking cat emblem if you replace this background decal as it requires breaking the studs off your old emblem to get it off. Check out this video ...

The 1967 XR7 did not have rocker panel mouldings as did the 1968 - 1973 XR7 Cougars. All 1967 XR7 models came equipped with these "Hash" marks fastened to the rear of both rockers, at a rear tilting angle. Both sides received seven ribs, held by two Phillips screws each for a total of fourteen ribs in all. They were painted semi-gloss black in the recessed areas and the screws themselves were black as well. The leading ribs are usually pretty rough looking due to road debris wear, the one...

Assembly required This high quality corral fits perfectly and the chrome plating is well beyond what Ford originally did. The mounting studs are placed in the exact position as original. We have offered the walking cat and black background for sometime now but the challenge has been getting your used corral (or rectangle frame) remounted after you break off the studs to remove the assembly. Replacing this emblem assembly is probably (for the money) the best way to improve the looks of the...

Used core emblem that will need a new background decal. May have one or two hard to find small pits but will be above average even for a Western car. Make sure you consider our reproduction part before you purchase this. This used unit will be harder to install due to the fact that they were only designed to be installed once. Click on images to enlarge. The above is a very sought after collectible that was circulated back in 1967-1968. This picture above (From Jim Pinkerton) is of a pen...

Reproduction grille mounting kit for the driver (left hand) and passenger (right hand) sides of the Mercury Cougar.

This is a Mustang kit and it includes 4 screws, 2 metal nuts, 2 self-threading plastic nuts and 2 anti-rattle bumpers as pictured.For Cougar, you need this kit plus 2 more plastic nuts, found here.

Flat nut for attaching the "Mercury" script on the front fender extension on all 1967-68 Mercury Cougars. 4 total needed for emblem installation on that fender extension. Also attaches the reproduction running cat emblem to the headlight door on 1967-69 Mercury Cougars.

Reproduction Front Bumper Guard Bolts & J Nuts for the 1967 - 1968 Mercury Cougar 

This reproduction tape is a must for anyone replacing their stainless steel window trim pieces on the 1967 - 1968 Cougar or Mustang. Can be used on any of the side windows. We suggest saving the original quarter window rubber surround if possible, due to the curves, but this tape can be used there as well if needed. This glass setting tape is designed to look and perform similarly to the original Ford factory material. It creates a water tight bond as well as...

Very rare to find one of these that has never been tapped in the slightest. We have a very limited quantity of grade A centers in stock. Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

The majority of our centers look like the rust free part you see pictured. They will need some minor body work before paint. We will not send you junk! Ford part # C7WY-8A047-A. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Good used part with no pitting or obvious damage. Includes stamped steel metal mounting bracket attached to the backside. Cougar part numbers: C7WY-13A137-B (Headlamp exterior cover) C7WY-13A155-A (Headlamp hinge) Check out this video

NOS part that shows shelf wear and may need to be repainted in places. For 1967 and early 1968 Cougars built prior 12/15/1967. Can easily be made to fit 1968. Ford part numbers: C7WY-13A137-B (Headlamp exterior cover)C7WY-13A155-A (Headlamp hinge) Check out this video ...

Good used eyelid with no pitting or obvious damage and is for 1967 and early 1968 Cougars built prior 12/15/1967. Includes emblem and metal mounting plate. Ford part # C7WY-13A136-B (Headlamp exterior cover) C7WY-13A154-A (Headlamp hinge) Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in your Cat? The videos below are your ticket! Check out this video ...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford part...

Used driver side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 2 screws and grind down 2 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Small section with two...

Used passenger side grille chrome only, just the chromed diecast section only for any 1967-68 Mercury Cougar. These will have minor blemishes from rocks and debris, overall the chrome will be way above average. We salvage these from our broken grille sections. These are fairly easy to remove from your grille half. 4 screws and grind down 16 mushroomed over pot metal tabs. Screws are usually adequate for reattaching, you might want to use a drop of Loctite on the threads. Replaces Ford...