Bumpers & Trim

Chromed quarter window moulding or 'hockey stick' mounting bracket for the driver side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529035-A Check out this video ...

Chromed quarter window moulding or 'hockey stick' mounting bracket for the passenger side only of 1967-68 Mercury Cougars. Also attaches the outer window fuzzy or belt line kit component. Stainless steel construction, these can be bonded to our reproduction quarter trims. Item cleaned for photos, item shipped will likely have the remnants of the window seal and road tested dirt.Replaces Ford part number C7WY-6529034-A Check out this video ...

If your Cougar came from a region that uses road salt your buckets are probably rusted in the corners or worse. Our dry "West Coast" buckets are 100% rust free and the mounting tabs are not broken from the removal of stubborn bolts. They will not be bent or damaged in any way. Keep in mind we do have grade B brackets for much less that only have minor bends or blems that could be easily corrected. *NOTE* These parts are far more important than most people realize. If they structural integrity...

These driver quality buckets are solid but will have a small bend, hairline crack or the beginnings of rust in a corner. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in these brackets are very powerful and if these brackets do...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable.  NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS.   *NOTE* These...

These driver quality passenger side headlight buckets are mostly solid but will have a small bend, hairline crack or the beginnings of rust in the corner closest to the battery. With minimal work they can be show quality or can be used for a driver as is. *NOTE* These parts are far more important than most people realize. If they structural integrity for any reason be it rust, collision or failed spot welds, you will be damaging your grille in a very short time. The vacuum actuators housed in...

These grade C headlight buckets will have rust and significant corrosion on the sides or corners (see photos above), but usually in the areas that are hidden when installed. A good part nonetheless, they're just not as pretty as one would hope for. This listing is for someone who doesn't care about the inner appearance, or maybe wants to do a little fabricating on their own to make the bucket presentable. NO RETURNS WILL BE ACCEPTED ON THESE GRADE C BUCKETS. *NOTE* These parts are far more...

These brackets are required to mount the optional rear bumper guards. They are not an exact reproduction but functionally they are spot on.Installation hardware is hard to come by, so you should hang on to yours and re-use them.Sold as a pair

These are the brackets required to mount the optional rear bumper guards. They mount behind the rear valance and are often overlooked when people part out a Cougar. *NOTE* As is often the case, service replacement parts are painted satin black and the originals installed on the assembly line were left natural. The mounting brackets are in fact supposed to have a natural finish if your car came with them from the factory.

This kit includes all new hardware, and both brackets. Mounting diagram not included (you can save and print the photo above). As shown, 1967 - 1968 rear bumper guards mount 17.5" from the center line of the car. Clip and bolt hardware kit will be new pieces.

This is a 100% accurate reproduction down to the captured lock washer and black Zinc coating. The only difference is that these are made from a substantially better grade of steel than the originals. These often break when you try to remove them to replace the vacuum actuator so if you are planning on doing that procedure we highly recommend buying these in conjunction with the actuators. Sold individually, two required per car. Cougar part number C7SZ-13A173-A. Also Fits: 1967 Ford...

This is the bolt that often gets destroyed when you try to remove it from the bottom side of the headlight bucket. Our West Coast Cougars come apart a little easier so we often are able to pull them with minimal effort. Cougar part number C7SZ-13A173-A. Application includes: 1967-68 Mercury Cougar and XR7, 1967-68 Ford Thunderbird, 1969-71 Lincoln Continental MK III. Do you want to replace those worn out actuators yourself or are you looking for some great information on aligning the grille in...

Attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Set of 16 attaching screws for the headlamp adjusting screws for the 1967-70 Mercury Cougar and most other Ford and Mercury cars and trucks. Each of the headlamp adjusting screws uses 2 of these screws. A Cougar with 4 headlights would need a total of 16 of these screws.

Bumper bolt nuts sold individually. Also available in our bumper bolt kit.Please know that chrome cracking from the installation of bumper bolts on our rechromed bumpers is not covered under warranty. We have observed that some reproduction wavy washers are of a thicker material than original and require more torque to flatten out properly for a good fit. We suggest that no matter what thickness your repro wavy washer is that you flatten them out in a vise prior to installation so as not to...

New plastic nut or insert for those 1/4 inch square holes in the grille for attaching the headlight doors (8 required there), and for the XR7 door pull panel mounting plates for attaching the actual door handles (2 required per side). Replaces Ford part # 379830-S1. Check out this video ...

Correct size and style white square plastic insert that clips onto front or rear license plate bracket on any 1967-73 Mercury Cougar. Each kit allows one license plate to be mounted. The actual screw has a large head which is made for license plates, but is not the factory Ford style of fastener for Concours judged cars. We also sell an accepted original style of screw, see item 8286.

Reproduction foam rubber donuts that help cushion the brace from the tail panel on any 67 - 73 Cougar or Mustang.Replaces Ford part number C5ZZ-6540996Sold as a set of 4.

If your core is not adequate we have cores for sale. Keep in mind you can get FREE trim parts from us if you have a quantity of good quality cores to exchange!Due to the difficulty in obtaining trim we no longer sell these without first having you send us your cores. For more info on aluminum trim restoration & core exchanging, check out our video below. ...

This purchase requires you send a good core in advance. If you happen to have a set of three NOS wheel lip mouldings and purchase the fourth as a restored piece from us it will visually fit right in. Restored is never as good as NOS as the polishing process will make the part thinner which means it will be more prone to damage than an un-restored original or NOS trim part.*Note - This is a core exchange item only, trim will not ship until your acceptable moulding core is received by...

This is the left hand or "Driver Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6529035-A. We have found that this 3M product works great for bonding these parts in place...

This is the right hand or "Passenger Side" 1/4 panel moulding. Some refer to this as a "Hockey Stick" or "J" moulding. It mounts at the base of the rear side windows and almost always needs to be replaced due to pitting or holes having been drilled in them to fasten these in place. Included with the moulding is super strength 3M double sided, trim tape. Original Mercury part number was C7WY-6551728-A.We have found that this 3M product works great for bonding these parts in place permanently....

New to the market grille fix for 1967 - 1968 Mercury Cougars / Patent Pending. These simple little grille repair clips have been needed since these cars were new! Over the years we have seen a multitude of home remedies to fix this common problem but none were this clean looking, easy to install and failure proof. Soon we will be listing all the different FoMoCo applications these clips will work on. These clips are sold as a set of four. NOTE: We've found that removing the legs from one side...

Reproduction hood latch return spring, attached to the sides of the hood latch on the 67 - 68 Cougar. Sold individually, 2 required for Cougar, 1 for Mustang.

Unfortunately the premium version is no longer available.  This version is made of a softer compound than the original bumpers and will not hold up as long as the originals did on a Cougar due to the force that the actuator exerts.  Sold as a Pair. Check out this video Check out this video

Used rubber sleeve from the front outer bumper mounting tube bracket. Must be for anti squeak or for protection of the front turn signal wiring harnesses. One per side, sold individually. The Ford part number for this item is C7WB-17B947-B. These were made from rubber tubing with a wall thickness of 1/8 inch. Inside diameter is approximately 7/8 inch, and about 1-1/2 inches long for these 1967-68 bumper sleeves. Limited to available stock.  ...

New black screws for attaching the headlight doors to all 1967-68 Mercury Cougars. Four screws needed per side for a total of 8 per car. We have found 3 different styles of separate screws that were used during the 1967-68 model run, San Jose and Dearborn may have accounted for a difference. This one matches exactly to one of the more common ones that were installed. Replaces Ford Part number 376352-S15.

Set of 13 black Phillips oval headed screws for attaching the face pads onto 1967 Mercury Standard Cougars (non-XR7 models). Sold as a set of 13 screws, also sold individually under SKU 100022556. *Note - These screws are a glossy black in color.

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD individually. See related items for kit of 10 screws. Fits: 1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970...

Stainless screw, most correct looking we have found. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. SOLD AS A SET OF 10.Fits:1967 Mercury Cougar1968 Mercury Cougar1969 Mercury Cougar1970 Mercury Cougar1971 Mercury Cougar1972...

Not 100% correct, but close and functional. In 1967 - 1968 there were eight per wheel lip moulding, two per fender extension moulding, two per center grille moulding and five per hood lip moulding for a total of 50 screws. In 1969 - 1973 they were used on the wheel lips mouldings. The 1971 - 1973 hood lip mouldings used the same screw but it was 5/8" tall. Sold as a box of 100.

These are not available new and differ from Mustang. We on occasion find one that is still pliable and intact. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

These are not available new and differ from Mustang. We on occasion find one that is still pliable and intact. Check out our video below for helpful tips on disassembling your vent and quarter windows: 67-68 Cougar/Mustang Vent & Quarter Windows - Disassembly for Restoration

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

Far superior to the reproductions offered, these used fillers are crack free with minimal scratches and no missing chunks. Just use soap, water and steel wool to clean them up. Sold individually, this is a driver side only. Hard to come by, this 'Grade A' part will have pliable rubber, and not have visible cracks or damage when installed. *NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The parts you will receive will be "as taken from a...

Used driver side (left hand) front fender to bumper slash shield for the Mercury Cougar. This is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This will look better than the reproductions, in our opinion, and will cost you less...

Far superior to the reproductions offered, these used fillers are crack free with minimal scratches and no missing chunks. Just use soap, water and steel wool to clean them up. Sold individually, this is a passenger side only. Hard to come by, this 'Grade A' part will have pliable rubber, and not have visible cracks or damage when installed. *NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The parts you will receive will be "as taken from...

Used passenger side (right hand) front fender to bumper slash shield for the Mercury Cougar. This is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that they may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This will look better than the reproductions, in our opinion, and will cost you less money....

Used driver side (left hand ) grade "A" rear quarter to bumper splash shield. Far superior to the reproductions offered, these used fillers are crack free with minimal scratches. Just use soap, water and steel wool to clean them up. Nothing fits and looks like original FoMoCo!Ford part # C7WY-6529031-A, engineering # C7WB-65280A95-A, and is also marked with an L to denote left side.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The parts...

This driver side (left hand) rear quarter to bumper splash shield is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that it may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This looks better than the reproductions, in our opinion, and will cost you less money. Ford part # C7WY-6529031-A, and...

Used passenger side (right hand ) grade "A" rear quarter to bumper splash shield. Far superior to the reproductions offered, these used fillers are crack free with minimal scratches. Just use soap, water and steel wool to clean them up. Nothing fits and looks like original FoMoCo!Ford part # C7WY-6529030-A, engineering # C7WB-65280A94-A, and is also marked with an R to denote right side.*NOTE* The parts pictured have been cleaned with steel wool for the sake of showing detail and quality. The...

This passenger side (right hand) rear quarter to bumper splash shield is what comes in on the majority of our parts cars. This used hard rubber part will have some sort of blemish in that it may be slightly warped, chipped, or have a visible scratch. Steel wool is a good way to clean it up and boiling it in water before install can often times make it appear less warped. This looks better than the reproductions, in our opinion, and will cost you less money. Ford part # C7WY-6529030-A, and...

Exact reproduction of originals but improved!On the originals, the mounting holes did not line up properly so we made them fit perfect!Made using the original Ford blue prints and a NOS original for the pattern. Replaces Ford part numbers C7WY16B555-A and C7WY-16B554-A

Quality exact reproduction rear quarter to bumper splash shields, also called bumper side fillers for the 67 - 68 Mercury Cougar.Sold as a pair.

This reproduction spring puts tension on the headlight adjusting ring so when you turn the screw on the adjusters the ring remains tight and will move as adjusted. Sold individually, four required per car. These small springs were used in 1967-68, a larger spring was used in 1969 through 1973.

This spring puts tension on the headlight adjusting ring so when you turn the screw on the adjusters the ring remains tight and will move as adjusted. Sold individually, four required per car. These small springs about 0.360" diameter, were used in 1967-68, a larger spring was used in 1969 through 1973, which will fit the early Cougar. Ford number C6SZ-13031-A.

Set of 20 replacement staples for the beltline kit. These are used to attach the beltline pieces to the door panel. Will work for any beltline kit on a number of different makes and models.

Many of our customers have asked and requested how we clean and detail our parts. We use a combination of items, mostly fine steel wool and elbow grease. Cleans haze, crud, and years of oxidation and water spots from glass, aluminum, chrome, and rubber.