Contact Us / Visit Us (click here)
CANADIAN CUSTOMER: Due to the Canada Postal Service strike, we recommend choosing DHL Express.
Note: UPS Mail Innovations is delivered by the post office and Canadian deliveries will be affected by the strike.
International Customers Click Here [Updated 6/2024]
 

Search This Category:
Select layout:
Products (Click sub-categories above to ONLY display results for that Sub-Category) 337-384 of 586
$0 Price: $89.05

Buy Details

Availability: In-Stock Item
Item #: 10017 -

This reproduction power window relay mounts to the front inner apron on the passenger side just behind the starter solenoid. This relay can also be used for 1969-73 power convertible tops, and 1971-73 power seat.Replaces Ford part #: C8AB-14677-A.Will replace D1AZ-14677-A, AND C1AF-14677-A but will not be an exact fit

$0 Price: $44.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11-0384 -

Used OEM Ford heater blower motor resistor that attaches to the heater blower fiberglass housing. We inspect these for damage or broken wires and we guarantee these will make your fan work. Not only was this heat resistor was factory installed on 1967-68 Mercury Cougar and 1965-68 Ford Mustang.Ford part # C2OA-18591-A or C8ZZ-18591-A*Note - Excludes Heater with integral or factory air conditioning.

$0 Price: $0.85

Buy Details

Availability: In-Stock Item
Item #: 17294 -

Retainer or keeper for door hinge pins on all 1968-73 Mercury Cougar and Ford Mustang, plus most all other Ford products with a typical door hinge pin. The factory installed the hinges with the pins driven in from the bottom as viewed with the doors installed. Most restorations install the pins from the top so that gravity holds them in. These retainers allow the pins to be mounted concours correctly. You must use a socket or other tool to install. These fit the door hinge pins with 5/16 inch...

$0 Price: $5.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 25279 -

Original retainer that clips onto the breather element nipple sticking through the air cleaner base and holds the elbow for the hose going to the PCV valve.  Ford calls this part the Crankcase Emissions Filter Retainer.The Master Parts Catalog says this part is only for 1971 and newer cars, but this part has been found on low mile 1970 cars as well. Ford part # D1AZ-9E628-A.

$0 Price: $14.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 33447 -

Used wiring harness retainer bracket for mounting the steering column bracket, on any 1973 Mercury Cougar or Ford Mustang. Retainer only, many of these are missing. Probably not missed, limited to stock on hand. Basic Ford part number 14A163.

$0 Price: $34.88

Buy Details

Availability: In-Stock Item
Item #: 15-0179 -

Used retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. Ford part number C9AZ-3E629-B. *NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

$0 Price: $36.45

Buy Details

Availability: In-Stock Item
Item #: 32067 -

Reproduction 3D printed retainer / friction clip that replaces broken injected plastic shaft retainers on fixed or tilt steering collapsible columns on most FoMoCo products starting in 1968 and through the 70's. These installs on the upper piece of what Ford called the Steering Column Shaft Assembly, also known as the inner steering column collapsible shaft.  The Steering Column Shaft Assembly is the 2 piece shaft that connects the steering wheel to the rag joint. The upper...

$0 Price: $22.86

Buy Details

Availability: In-Stock Item
Item #: 15-0173 -

Used return spring for any 1970 - 1978 Cougar or Mustang Tilt Column. This spring provides return tension on tilt steering wheels.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year.

$0 Price: $1,152.54

Buy Details

Availability: In-Stock Item
Item #: 32202 -

NOS Studiosonic Reverberation Sound System for the 1967 Mercury Cougar, Ford Mustang Coupe, Galaxie, LTD, Fairlane (except wagon and convertible), Thunderbird, Monterey, Marquis, Marauder, Comet, Cyclone.The Studio Sonic reverberation system is operated with the radio fader control and a foot switch located near the headlight dimmer switch. Depression of the switch will add reverberation in the rear speaker(s).NOTE - The original installation sheet is missing from this kit, we've...

$0 Price: $7.62

Buy Details

Availability: In-Stock Item
Item #: 14-0031 -

New RTV  oil resistant, high temperature, Ultra Black gasket maker for use on the Mercury or Ford. It's no mistake that Ultra Black has become an automotive industry standard. It's low odor, flexible, non-corrosive, vibration resistant, oil resistant, heat resistant, fast curing formula cannot be beat. Great for use on any surface that experiences high heat and oil like the valve cover gaskets.

$0 Price: $2.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 15-0043 -

Three required per car, includes lock washer. This screw is used with a fastener to fasten the outer tube to the lower knuckle. This is an allen head screw. The fastener use with this screw has two styles one is for 1967 - 1969 (15-0116) and the other is for 1970 thru 1974 (15-0117).*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

$0 Price: $15.85

Buy Details

Availability: In-Stock Item
Item #: 33381 -

Top Loader transmission input shaft seal, small shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University.*Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

$0 Price: $16.49

Buy Details

Availability: In-Stock Item
Item #: 33379 -

Top Loader transmission rear seal, 28 splined shaft, 289, 302, 351, and 390 only. Quality Timken part. Fits all 3 and 4 speed Top Loader Ford transmissions 1967-73 Mercury Cougar and 1965-73 Ford Mustang. Follow manufacturers instructions for installation or go to YouTube University. *Note - excludes big shaft 428CJ, 429CJ, and Boss 429 transmissions.

$0 Price: $38.25

Buy Details

Availability: In-Stock Item
Item #: 32360 -

Finally! A cure for those peeling chrome bezels on your car with deluxe seat belts. If your plastic bezels on your 68-72 standard belts are two part construction, you can upgrade with these attractive bezels. Before these were reproduced we used to hunt high and low for good used units from rear belts out of parts cars. Perfect fit and great quality. Sold as a pair, six per car on coupes, four per car required on convertibles. Replaces Ford part # C8AZ-65611A72-A

$0 Price: $55.89

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 14-1011 -

Both deluxe and standard used the same retractor in 1968 - 1969 and left is the same design as right. Grade "B" retractors will be 100% functional but cosmetically will show a crack in the plastic holster, and may have minor rust on chrome. Keep in mind no retractor was used in convertibles until 1972, only a lap belt. NOTE: Front retractors are same for left and right, and are good for all 67-73 Cougar AND Mustang applications. Check out our video "All about seat belts" below. ...

$0 Price: $13.15

Buy Details

Availability: In-Stock Item
Item #: 11348 -

Oil pressure switch with press on wiring connector. 1967-73 Mercury Cougar and Ford Mustang. This is the warning light style of sending unit. Cougar body code 65A and 65C, excludes Eliminator. Additionally this sending unit also fits 1970 and newer Ford Maverick and Mercury Comet, 1968-69 Lincoln with 460 engines, and 1967-71 mid sized Ford and Mercury cars such as Cyclone, Fairlane, and Torino.Check out the video below on our new gauge tester: ...

Sequential Flasher - Custom Conversion Kit - Plasma LED's - NOT FOR THE COUGAR - New ~ Any Car With 6 Taillights
1969 Ford Thunderbird, 1970 Ford Thunderbird, 1971 Ford Thunderbird, 1968 Shelby Mustang, 1969 Shelby Mustang, 1970 Shelby Mustang
0
$0 Price: $257.95

Buy Details

Availability: In-Stock Item
Item #: 20675 -

This sequential flasher is an electronic flasher kit to provide sequential tail lights to any automobile with two or three tail lights per side, and are using Plasma LED's. Parts included in this kit are: Sequential Control Unit with pre-soldered connectors, electronic flasher can typical application schematic, and trouble shooting guide. We have had everyone from Truckers wanting sequential lights on their mud flaps to 1966 Dodge Charger owners purchase this easy to install trouble free kit....

$0 Price: $658.55

Buy Details

Availability: In-Stock Item
Item #: 31017 -

Reproduction set of Deluxe seat belts for the 68 - 69 Cougar or Mustang Coupe. Some things you may want to notice are that although these are made to fit both 68 and 69, the webbing is the 68 style. 1968 belts had four rows of material that make up the belt and 1969 belts had three rows (as seen in the picture above). Also, the rear belts will not have the plastic sheaths that keep the belts from falling in between the seats. These belts are premium quality and come complete with deluxe...

Shaft Bushings - Grille / Headlight Eyelid Door - PAIR - Repro ~ 1969 - 1970 Mercury Cougar
1970 and newer Lincoln Continental
1970-71 Mercury Cyclone
1972 Lincoln MK IV
1969-71 Mercury Brougham, Marquis, Monterey, Colony Park, or Marauder, including X100 and station wagons
1970-71 Ford Torino
1968-69 Pontiac GTO w/ Hide-Away Headlights
1967-68 Pontiac Grad Prix w/ Hide-Away Headlights
0
$0 Price: $17.35

Buy Details

Availability: In-Stock Item
Item #: 16194 -

Repro bushings (pair) that mount to the grille for the headlamp operating shafts. These hardly ever survive after 40 years. Technically not needed, and most never knew they existed. Sold as a pair, one for each side. When mounted these are tight, it was no wonder they are seldom seen on cars. Even the NOS bushings are tight. We recommend polishing the headlight shaft with emery or sand paper, to make both sides smooth. Definitely add a little bit of lubricant too. Replaces Ford part number...

$0 Price: $29.57

Buy Details

Availability: In-Stock Item
Item #: 31132 -

UPDATE 11-19-20: We still do not have the shaft seal dialed in but we are offering this kit with a proven substitute seal until further notice. This kit will recondition most FoMoCo headlamp actuators built from 1967 into the 70's on most any Thunderbird, Torino, Lincoln, Cyclone or Marquis. The kit will service two actuators even though many cars only come with one center mounted unit. If your actuator holds vacuum on the bottom port but does not hold vacuum (or pressure) on the top port then...

$0 Price: $120.02

Buy Details

Availability: In-Stock Item
Item #: 16794 -

Restored shifter T handle as found starting in 1968 and through, 1972 Mercury Cougar and Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little thicker in the body, compared to earlier designs. Core charge applies. Replaces Ford part number C8OZ-7213-A. Check out our video on rebuilding your shifter below: ...

$0 Price: $120.02

Buy Details

Availability: In-Stock Item
Item #: 16758 -

Restored shifter T handle as found on all 1973 Mercury Cougar or Ford Mustang with automatic transmissions. This handle will actually fit on most Ford automatic floor shift levers of the era. Design is a little more ergonomic in design, compared to earlier designs. Core charge applies.Replaces Ford part number D3OZ-7213-A.

$0 Price: $38.85

Buy Details

Availability: In-Stock Item
Item #: 33189 -

Shift kit for the C4 transmission valve body for all 1967-67 Mercury Cougar and 1967-69 Ford and Mustang. This is a standard shift rebuilding kit for your stock valve body.

$0 Price: $52.85

Buy Details

Availability: In-Stock Item
Item #: 33190 -

Shift kit for the FMX transmission valve body for all 1969-72 and 1969-72 Mercury and Ford. This is a standard shift rebuilding kit for your stock valve body.* Note - 1973 has a different shift kit, see related items.

$0 Price: $127.27

Buy Details

Availability: In-Stock Item
Item #: 30256 -

Very hard to find 69 - 70 Shelby / 67 - 69 Cougar 4 speed shifter knob. Almost a year in development was spent to get as close as possible to original N.O.S. sample. These very rarely come up for sale used and when they do, they are expensive. Knob insert is made of metal just like original not brass. Knob also has the correct groove in middle of body like 69 version and not the earlier version which does not. Not technically correct for a 67-8 Cougar, as the 67-8 does not have the groove in...

$0 Price: $87.22

Buy Details

Availability: In-Stock Item
Item #: 26714 -

These shocks are the as close to original specs as possible for the Mercury Cougar. This is the performance shock for those looking for firmer ride. The KYB Gas-a-Just shocks use higher gas pressure to keep your tires glued to the road. The KYB Gas-a-Just shocks' velocity-sensitive valving system adjusts quickly to changing road conditions for maximum comfort in any situation. Their mono tube configuration eliminates aeration and foaming, their micro-smooth, hard-chromed pistons extend their...

$0 Price: $27.85

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 12167 -

Good used driver Quality, no cracks in lens and not pitted but will show "patina". Ford part #C8GY-13380

$0 Price: $18.85

Buy Details

Availability: Rare / NOS Part
Item #: 33854 -

New Old Stock, NOS rear reflector gasket. This pad goes between the rear quarter panel and quarter panel reflector on the 1968 Mercury Cougar only.  Replaces Ford part #: C8WY-13493 or C8WY-13A493-A. *Note - These were not installed on Ford Mustangs, but they could be installed since they use the same reflector after Feb 15, 1968.

$0 Price: $11.85

Buy Details

Availability: In-Stock Item
Item #: 26625 -

These pads go between the rear quarter panel and quarter panel reflector on the 1968 Mercury Cougar only. Sold as a pair.  Replaces Ford part #: C8WY-13493 or C8WY-13A493-A. *Note - These were not installed on Ford Mustangs, but they could be installed since they use the same reflector after Feb 15, 1968.

$0 Price: $3.87

Buy Details

Availability: In-Stock Item
Item #: 31889 -

These are the caps placed on the inside of the rear marker reflectors to protect your trunk's contents from damage. These Reproductions are grey. They were originally black with varying shades of grey. Sold in pairs, two pairs per car. Click on images to enlarge. Here is the Rear Marker Reflector without a cap. Here is the new cap on the marker. After you install the Rear Marker, screw the cap onto the Marker from the inside of the trunk. Below is a good used cap on the Marker. ...

$0 Price: $120.00

Buy Details

Availability: Rare / NOS Part
Item #: 33855 -

NOS rear side reflector used on the 1968 Montego / Cyclone / Cougar for the 1968 model year. Listing is for the reflector only, does not come with gasket or hardware. Also, don't forget the rubber protectors that slip over the pointy studs inside the trunk. Replaces Ford part #C8GY-13380-A.

$0 Price: $69.15

Buy Details

Availability: In-Stock Item
Item #: 11288 -

Nice reproduction rear body side reflector as found on 1968 Mercury Cougars. Used on Montego / Cyclone / Cougar for the 1968 model year. Great reproduction, but without the 'FoMoCo' marking like on our concours version. This reflector comes with the rubber gasket and attaching nuts. Very nice and at an attractive price. You'll also want these rubber protectors for the trunk.Replaces Ford part # C8GY-13380-A. *Note - Also fits 1968 Mustang after Feb 15, 1968. *Trivia - 1968 Mustangs did not...

$0 Price: $64.91

Buy Details

Availability: In-Stock Item
Item #: 14373 -

Perfect in every detail down to the FoMoCo logo. Used on the 1968 Montego / Cyclone / Cougar for the 1968 model year. Great reproduction made from the original Ford tooling. This is the Concours version with FoMoCo marking on the lens. Listing is for the reflector only, does not come with gasket or hardware. Also, don't forget the rubber protectors that slip over the pointy studs inside the trunk. Replaces Ford part #C8GY-13380. ...

$0 Price: $68.05

Buy Details

Availability: Out of Stock
Item #: 25978 -

Reproduction manually adjustable convex passenger side view mirror in chrome for the Mercury Cougar or Ford Galaxie.  Gasket and screws included. Replaces Ford part # C7AZ-17696. Dimensions: Base Hole Spacing: 5-7/8" Base Length: 6-5/8" Overall Height: 5-1/8" Mirror Width: 5-1/8" Mirror Height: 3-5/16" Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

$0 Price: $23.85

Buy Details

Availability: In-Stock Item
Item #: 26776 -

*NOTE* EARLY 69's USED THE 2112 MIRROR FOR BOTH PASSENGER AND DRIVER SIDES. LATE 69's USED TWO DIFFERENT SIZES FOR EACH SIDE (2124 for driver side, and 2112 for passenger side). BEFORE ORDERING, PLEASE CHECK YOUR DIMENSIONS AND COMPARE TO OUR LISTINGS. Precision cut replacement lens for any Ford product with sport mirror. This fits any FoMoCo Sport mirror 69 and up. Comes with two round pieces of double sided tape.  Lens measures 4 3/8 X 2 7/8. Do you have questions about installing the...

$0 Price: $35.87

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 24774 -

Empty shell / head / housing only for a passenger side manual adjust mirror. Found on all FoMoCo products utilizing a manual mirror 1969 - 1973. The remote mirror heads found on many 1970's Ford products do not interchange with the manual "Bullet Style" mirrors. Most customers find our reproduction unit to be a better value as it comes with the mirror and mounting hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video ...

$113.99 Price: $167.75

Buy Details

Availability: In-Stock Item
Item #: 13889 -

Fits and looks identical to the 1970 mirror base but is slightly taller. The difference in height between the two versions is indiscernible to the naked eye. Very nice product, works well with original mirror heads, save your hardware. Do you have questions about installing a passenger side mirror or using Riv-Nuts? Check out this video Check out this video ...

$0 Price: $7.45

Buy Details

Availability: In-Stock Item
Item #: 14-0019 -

New spray silicone lubricant for the squeaky Mercury or Ford. This spray lubricant is great for door hinges, trunk hinges, hood hinges and basically anything else that needs to be lubricated. Easy to use and will definitely de-squeak your vehicle.

$0 Price: $2.88

Buy Details

Availability: In-Stock Item
Item #: 15-0178 -

Used snap ring that is used to hold the bearing on you the steering shaft. This ring was used on 67 - 78 fixed columns and 70 - 78 tilt columns. Not for use on 67 - 69 tilt columns.*NOTE* For tilt column service, you can contact Tony Augustine at 6t8cougarguy@gmail.com. Tony is a trusted colleague of WCCC and we've sent many customers his way since our column specialist retired last year. ...

Socket - Clutch Equalizer - PAIR - Repro ~ 1971 - 1973 Mercury Cougar / 1971 - 1973 Ford Mustang
1965 - 1971 Ford Galaxie and Full Size (Galaxie, XL, LTD, Custom 500 etc..)| 1970 Torino 429|1972 - 1976 Ford Torino, Gran Torino and Ranchero |1973 - 1976 Ford Maverick
0
$0 Price: $22.75

Buy Details

Availability: In-Stock Item
Item #: 14065 -

Replacement pair of Clutch Equalizer Bar ( Z-Bar) Bushings. These are for manual transmission equipped models and are a bushing that is no longer available from Ford. These are the split bushing style that replace Ford part number C5AZ-7543-C. These fit 1965 1966 1967 1968 1969 1970 1971 Ford Galaxie and Full Size Models (Galaxie, XL, LTD, Custom 500 etc..), 1970 Torino 429 Models, 1971 1972 1973 Mustang, 1972 1973 1974 1975 1976 Ford Torino, Gran Torino and Ranchero models and 1973...

$0 Price: $176.75

Buy Details

Availability: In-Stock Item
Item #: 12135 -

This new version sequential box works with either standard or plasma LED bulbs NOTE: Although your existing emergency flasher might work just fine with the new sequential unit, it is highly recommended that you also use the same updated electronic sequential flasher in its place to guarantee proper operation. This is a direct fit replacement, just pop open your black plastic box located in the driver side trunk drop off and plug it in. Your January 1970 and newer Cougar will have...

$0 Price: $2.88

Buy Details

Availability: Used / Wrecking Yard Item
Item #: 11907 -

Used alternator fan spacer for the 1967 - 1973 Mercury Cougar or Ford Mustang.  This spacer also fits many other Ford applications.  Ford part number: C5AZ-10A344-B.