All Products

Reproduction Alternator Connection Nut for the 1967 - 1969 Mercury Cougar - 1967 - 1969 Ford MustangSold insividually 

Reproduction Alternator Connection Nut for the 1970 Mercury Cougar or Ford MustangSold individually

Contains nut, lock washer, and spacer. Fits all Ford alternators.

Reproduction Alternator Pulley Nut for the 1967 - 1973 Mercury Cougar - 1967 - 1973 Ford MustangSold individually 

Hard plastic terminal covers for the alternator. Replaces Ford Part #c7zz-14056-A

Spring that holds the headlight trim ring on each headlamp to the grille. 4 springs per car, sold individually.Ford number C6AZ-13031-C.

Reproduction Anchor Strap - Tape In for the 1967 - 1973 Mercury Cougar / 1967 - 1973 Ford Mustang

Mustang part that has incorrect thickness and a slightly different overall geometry to it. We also carry the correct Cougar version of this gasket, but only in used form.Replaces part # D1ZZ-18898.

These keep the trunk hinge spring rods from rattling. These are a reproduction of the anti-rattler for 67-68 Cougar / 65-68 Mustang.   Replaces Ford part # C5ZZ-6545028. These also work for the 69-70 Cougar / Mustang better than what came factory, which, according to the Ford MPC, for 69-70 would have actually been 1/8" x 7/8" Vinyl Foam Weatherstrip Tape, Ford part C6AZ-19627-A. Check out our trunk torsion bar installation video: ...

Reproduction anti-squeak pad for the leaf springs found on the Mercury Cougar or Ford Mustang. This little unit goes between each individual leaf spring and prevents metal to metal contact. These are sold individually and eight are required per car. Our reproduction leaf springs come with this pad pre-installed. Replaces Ford part # C0AA-5586.

Replica antifreeze tag that would have been found on the 1970 - 1973 Cougars and Mustangs when they shipped from the factory. See the product images for an example of factory placement.

Reproduction burl woodgrain decal for the 1968 XR7G sunroof / fog light switch.

Reproduction apron nuts for the 67 - 70 Cougar or Mustang. These are the fasteners that are imbedded into the aprons on either side of the engine compartment and are used to fasten the hood hinges to the car. Sold in a pack of 6 fasteners.

More accurate reproduction of the 1967 and 1968 XR7 Armrest Plugs. The difference in this pair, as compared to the set of four we sell, is that these will have a more accurate flat headed finish to them and will sit flush with the armrest face. Only available in Black. Sold as a pair Replaces Ford part # C7ZZ-6524056 or C8ZZ-6524056.

Decent reproduction of the 1967 and 1968 XR7 Armrest Plugs. Only available in Black. Sold as a SET OF FOUR. Replaces Ford part # C7ZZ-6524056 or C8ZZ-6524056.

Sold individually # 374212-S

Fits 1967 and 1968 Standard or XR7

Captured washer, or spinning washer nut for attaching the headlamp motors or vacuum actuators on the 1969-70 Mercury Cougar. All models, Standard Hard Top, XR7, and Eliminator. Two needed per car, sold individually.

Reservoir Attaching Nut 351335-S38 - Used Nuts for attaching the oil reservoir to the pump. The larger of the two nuts goes against the can. Threads of 5/8"-18 to fit the high pressure port. This is a pair of nuts, one tall and one short. Please follow the assembly procedures for the Ford power steering pump in the Ford shop manuals. Fits all small block V-8 engines, except for 1970 with 351 engine, and Mustang with 302 engines. 1970 302 / 351 engines used a different pump with an offset...

High quality rubber molded around a flexible steel insert. Insert is cadmium plated to prevent rust. A popular replacement item, as they always wear. While this unit also fits the 1965-68 Mustang, it is only correct for the 1968 Cougar XR7-G. Replaces Ford Part #: C5ZZ-7D351 Check out our video on rebuilding your shifter below: ...

Replaces Ford Part # 50828-S Sold individually. Zinc Dichromate (yellow-rainbow)

This is a replica of the warning tag that came on positive (+) terminal of Autolite batteries when the 1967 - 1972 Cougars and Mustangs were shipped from the factory.

Reproduction Autolite Fl - 1 Oil Filter Decal for the 1967 - 1972 Mercury Cougar or Ford Mustang 

Replaces Ford Part #: D3AE-9C485-AFA

OEM style nut to hold the axle U-bolt to the axle. Fine threaded like originals 7/16-20 grade 5. Will not fit some reproduction U-bolts. Sometimes these are called shock plate bolts. Replaces Ford part # 379244-S

This lens comes without the correct FoMoCo logo, sold individually. Replaces Ford Part # C5ZZ-15514.

These Back Up Light Lens Gaskets are sold as a pair. Fits the 67 and the 68. Replaces Ford part # C5ZZ-15510.

The correct color for the Cougar was gray but many prefer these black Mustang gaskets. Sold as a pair.

These Back Up Light To Rear Valance Seals are Sold as a pair. Fits the 67 and the 68. Replaces Ford part #: C7ZZ-15533. Note, gray is in fact the correct color for these, Mustang used black in 67-68. Note we also have black available for those who prefer.

These Back-Up Lamp Lenses are exact copies of the originals which come with the FoMoCo Logo. Sold Individually. Includes screws!

Sold individually. Stainless Steel

Protects door panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C5AZ-6223370-A.

Protects quarter panels from the abrasive action of rotating handles. Made from a very hard nylon type material featuring the correct milky white color. Replaces Ford Part #: C4SZ-6323370-A.

Reproduction backup light mounting spacers for the Mercury Cougar or Ford Mustang.

Reproduction barrel nut or insert for attaching "Cougar" fender script to the fenders. Each Cougar emblem uses 4 of these barrel nuts which insert into the fender first, and then the Cougar emblem. Additionally, these nuts also go into the C pillars for attaching the XR7 badge or medallion on each side. Two barrel nuts per side for the XR7 medallions. Barrel nuts sold individually. The install is basically the same as shown here: https://youtu.be/mcd788WUNns ...

Barrel nut for the 3/16" stud found on the 6.5 Liter badge and the GT badges that mount on the fender of 1967 Mercury Cougar and Mercury Cyclone GT with the S code 390 engine. Same GT badge on the 1968 Mustang GT models. Item sold individually. The install is basically the same as shown here: https://youtu.be/mcd788WUNns

Tubular or barrel nut for attaching our reproduction "C" pillar XR7 emblems with studs. We found these fasteners to install the emblems without disturbing the headliner of a 1967-68 Mercury Cougar. These are also suitable for installing this emblem onto the trunk lids of 1971-73 Mercury Cougar XR7 models. The originals were flat backed and glued onto the deck lids with adhesive. These tubular nuts require two 7/32" holes be drilled. These mount on the lower part of the roof behind the...

No more crust, white powdery battery terminals. Just spray this stuff on, and after a few minutes....simply wash off with water! Not only can you use this stuff on your car, you can use it on your ATV's, quads, dirt bikes and even your ride on lawnmower! A handy item to have laying around your garage. Of course, there's a little more messy, mostly free alternative which you can find the ingredients for online, but why bother? This is a simple, fairly cheap product to have.  

Reproduction "Battery OK" Decal for the 1967 - 1982 Mercury Cougar / Ford Mustang

Fits Standard and XR7

Reproduction Battery Tray Bolts & U Nuts for the 1968 Mercury Cougar / Ford Mustang

Inexpensive upgrade, replaces that bezel damaged by improper screw driver removal. We also sell the special tool that removes this without hassle or damage

Used ignition lock cylinder bezel for any 1967-68 Mercury Cougar, ford Mustang and likely Fairlane / Comet. Good used condition, we recycle the pitted crusty ones. Half the price of the repop version. We also sell the special tool that removes this without hassle or damage.Replaces Ford part number C6OZ-11584-A.

Reproduction bezel for the side marker lights on the Mercury Cougar or Ford Mustang. This unit features the correct contour that fits the car perfectly where other reproductions are often flat. Used with front and rear 1969 marker lenses and fits almost all 1969 Ford and Mercury cars. Includes speed nuts.Replaces Ford part # C9AZ-15A440-A, casting # C9AB-15A466-A.

Used bezel for the side marker lights on the Mercury Cougar or Ford Mustang. Used with front and rear 1969 marker lenses and fits almost all 1969 Ford and Mercury cars.  Ford part # C9AZ-15A440-A, casting # C9AB-15A466-A.

Starting in 1972 the 'Fasten Seat Belt' warning light was relocated to the center of the dash for visibility of all occupants of the vehicle. This is the bezel only that fastens to the instrument clusters of all 1972-73 Mercury Cougar models.Replaces Ford part # D2WB-10D841-AB.

Used wiper switch bezel for any 1969-70 Mercury Cougar or Ford Mustang. This is a used bezel that has been inspected for pits in the chrome. This used unit will likely have one of the rear orientation tabs broken, but other than that it will be a good used part. Excellently priced, compared to the reproduction. Here is a helpful youtube video on how to go about removing a headlight switch from a Cougar or Mustang. Replaces Ford part #: C9ZZ-10852. ...

There are two of these rings on the driver side cluster. One outlines the tachometer and one outlines the speedometer. Sold individually, two per car.